Volume 5: Turbo Expo 2002, Parts A and B
Latest Publications


TOTAL DOCUMENTS

122
(FIVE YEARS 0)

H-INDEX

12
(FIVE YEARS 0)

Published By ASMEDC

079183610x

Author(s):  
Y. I. Biba

As part of a revamp or rerate study, an investigation was undertaken to assess the impact of a collector design versus a volute on compressor performance. The subject compressor was a single stage, axial inlet configuration with a discharge collector rather than the more commonly used scroll volute. The primary distinction between the collector and volute is that the collector cross sectional area is constant at all circumferential locations. A complex 3D model containing the inlet, impeller, low solidity diffuser (LSD), and collector was built. A similar model was also created where the volute was substituted for the collector. Computational Fluid Dynamics (CFD) analyses were performed using these models with results generated at different flow rates. Computational results are presented and compared to test data for collector configuration. The test included standard performance measurements as well as more detailed internal flow data, allowing a credible comparison with the CFD results. Conclusions are drawn with respect to potential compromises in choosing a collector versus a volute.


Author(s):  
Chan-Sol Ahn ◽  
Kwang-Yong Kim

Design optimization of a transonic compressor rotor (NASA rotor 37) using the response surface method and three-dimensional Navier-Stokes analysis has been carried out in this work. The Baldwin-Lomax turbulence model was used in the flow analysis. Three design variables were selected to optimize the stacking line of the blade. Data points for response evaluations were selected by D-optimal design, and linear programming method was used for the optimization on the response surface. As a main result of the optimization, adiabatic efficiency was successfully improved. It was found that the optimization process provides reliable design of a turbomachinery blade with reasonable computing time.


Author(s):  
Mehrdad Zangeneh ◽  
Damian Vogt ◽  
Christian Roduner

In this paper the application of 3D inverse design code TURBOdesign−1 to the design of the vane geometry of a centrifugal compressor vaned diffuser is presented. For this study the new diffuser is designed to match the flow leaving the conventional impeller, which is highly non-uniform. The inverse method designs the blade geometry for a given specification of thickness and blade loading distribution. The paper describes the choice of loading distribution used in the design as well as the influence of the diffuser inlet flow distribution on the vane geometry and flow field. The flow field in the new diffuser is analysed by a 3D viscous flow code and the result is compared to that of the conventional diffuser. Finally the results of testing the stage performance of the new diffuser is compared with that of the conventional stage.


Author(s):  
A. R. Wadia ◽  
P. N. Szucs ◽  
D. W. Crall ◽  
D. C. Rabe

Previous experimental and analytical studies conducted to compare the performance of transonic swept rotors in single stage fans have demonstrated the potential of significant improvements in both efficiency and stall margin with forward swept blading. This paper extends the assessment of the payoff derived from forward sweep with respect to aerodynamic performance and stability to multistage configurations. The experimental investigation compares, on a back-to-back test basis, two builds of an advanced good efficiency, high pressure ratio, two-stage fan configuration tested alternately with a radial and a forward swept stage 1 blade. In the two-stage evaluations, the testing was extended to include the effect on inlet flow distortion. While the common second stage among the two builds prevented the overall fan from showing clean inlet performance and stability benefits with the forward swept rotor 1, this configuration did demonstrate superior front stage efficiency and tolerance to inlet distortion. Having obtained an already low distortion sensitivity with the radial rotor 1 configuration relative to current production military fan standards, the sensitivity to inlet distortion was halved with the forward swept rotor 1 configuration. In the case of the 180-degree one-per-rev distortion pattern, the two-stage configuration was evaluated both with and without inlet guide vanes (IGVs). The presence of the inlet guide vanes had a profound impact in lowering the two stage fan’s sensitivity with inlet distortion.


Author(s):  
Kai U. Ziegler ◽  
Heinz E. Gallus ◽  
Reinhard Niehuis

The interaction between impeller and diffuser is considered to have strong influence on the flow in highly loaded centrifugal compressors. However, the knowledge about this influence is still not satisfying. This two-part paper presents an experimental investigation of the effect of impeller-diffuser interaction on the unsteady and the time averaged flow configuration in impeller and diffuser and the performance of these components. The flat wedge vaned diffuser of the investigated stage allows an independent adjustment of diffuser vane angle and radial gap between impeller exit and diffuser vane inlet. Attention is mainly directed to the radial gap, as it determines the intensity of the impeller-diffuser interaction. In part I it was shown that smaller radial gaps improve diffuser pressure recovery, whereas impeller efficiency is hardly affected. Part II focuses on the reasons for these effects. Measurements with a laser-2-focus velocimeter in the highly unsteady flow field between the impeller exit region and diffuser throat were performed at three different diffuser geometries allowing a detailed flow analysis. Especially the unsteady results show that for a smaller radial gap more impeller wake fluid is conveyed towards the highly loaded diffuser vane pressure side reducing its loading and leading to a better diffusion in the diffuser channel. Concerning the impeller flow, it was found that a smaller radial gap is leading to a noticeable reduction of the wake region at impeller exit. The experimental results are intended to be published as an open CFD testcase under the name “Radiver”.


Author(s):  
Jan E. Anker ◽  
Ju¨rgen F. Mayer

This paper presents the simulation of the flow in a 1.5 stage low-speed axial turbine with shrouded rotor blades and focuses on the interaction of the labyrinth seal leakage flow with the main flow. The presented results were obtained using the Navier-Stokes code ITSM3D developed at University of Stuttgart. A comparison of the computational results with experimental data of this test case gained at Ruhr-Universita¨t Bochum verifies that the flow solver is capable of reproducing the leakage flow effects to a sufficient extent. The computational results are used to examine the influence of the leakage flow on the flow field of the turbine. By varying the clearance height of the labyrinth in the simulations, the impact of the re-entering leakage flow on the main flow is studied. As demonstrated in this paper, leakage flow not only introduces mixing losses but can also dominate the secondary flow and induce severe losses. In agreement with the experimental data the computational results show that at realistic clearance heights the leakage flow gives rise to negative incidence over a considerable part of the downstream stator which causes the flow to separate.


Author(s):  
Rolf Sondergaard ◽  
Jeffrey P. Bons ◽  
Matthew Sucher ◽  
Richard B. Rivir

An experimental investigation has been conducted into the feasibility of increasing blade spacing (pitch) at constant chord in a linear turbine cascade. Vortex generator jets (VGJs) located on the suction surface of each blade in the cascade are employed to maintain attached boundary layers despite the increasing tendency to separate due to the increased uncovered turning. Tests were performed at low Mach numbers and at blade Reynolds numbers between 25,000 and 75,000 (based on axial chord and inlet velocity). The vortex generator jets (30 degree injection angle and 90 degree skew angle) were operated with steady flow with momentum blowing ratios between zero and five, and from two spanwise rows of holes located at 45% and 63% axial chord. In the absence of control, pitch-averaged wake losses increase up to 600% as the blade pitch is increased from its design value to twice the design value. With the application of VGJs, these losses were driven down to or below the losses at the design pitch. The effectiveness of VGJs was found to increase modestly with increasing Reynolds number up to the highest value tested, Re = 75,000. The fluid phenomenon responsible for this remarkable range of effectiveness is clearly more than a simple boundary layer transition effect, as boundary layer trips installed on the same blades without VGJ blowing had no beneficial effect on blade losses. Also, tests conducted at elevated levels of freestream turbulence (4% at the cascade inlet) where the suction surface boundary layer is generally turbulent, showed wake loss reduction comparable to tests conducted at the nominal 1% freestream turbulence. For all configurations, blowing from the upstream row had the greatest wake influence. These findings open the possibility that future LPT designs could take advantage of active separation control using integrated VGJs to reduce the turbine part count and stage weight without significant increase in pressure losses.


Author(s):  
G. Ferrara ◽  
L. Ferrari ◽  
C. P. Mengoni ◽  
M. De Lucia ◽  
L. Baldassarre

Extensive research on centrifugal compressors has been planned. The main task of the research is to improve present prediction criteria coming from the literature with particular attention to low flow coefficient impellers (low width to radius ratios) where they are no more valid. Very little data has been published for this kind of stages, especially for the last stage configuration (with discharge volute). Many experimental tests have been planned to investigate different configurations. A simulated stage with a backward channel upstream, a 2D impeller with a vaneless diffuser and a constant cross section volute downstream constitute the basic configuration. Several diffuser types with different widths, pinch shapes and diffusion ratios were tested. The effect of geometric parameters on stage stability has been discussed inside part I of the present work; the purpose of this part of the work is to illustrate the effect of the same geometric parameters on stage performance and to quantify the impact of stability improvements on stage losses.


Author(s):  
J.-S. Liu ◽  
M. L. Celestina ◽  
G. B. Heitland ◽  
D. B. Bush ◽  
M. L. Mansour ◽  
...  

As an aircraft engine operates from sea level take-off (SLTO) to altitude cruise, the low pressure (LP) turbine Reynolds number decreases. As Reynolds number is reduced the condition of the airfoil boundary layer shifts from bypass transition to separated flow transition. This can result in a significant loss. The LP turbine performance fall-off from SLTO to altitude cruise, due to the loss increase with reduction in Reynolds number, is referred to as a lapse rate. A considerable amount of research in recent years has been focused on understanding and reducing the loss associated with the low Reynolds number operation. A recent 3-1/2 stage LP turbine design completed a component rig test program at Honeywell. The turbine rig test included Reynolds number variation from SLTO to altitude cruise conditions. While the rig test provides detailed inlet and exit condition measurements, the individual blade row effects are not available. Multi-blade row computational fluid dynamics (CFD) analysis is used to complement the rig data by providing detailed flow field information through each blade row. A multi-blade row APNASA model was developed and solutions were obtained at the SLTO and altitude cruise rig conditions. The APNASA model predicts the SLTO to altitude lapse rate within 0.2 point compared to the rig data. The global agreement verifies the modeling approach and provides a high confidence level in the blade row flow field predictions. Additional Reynolds number investigation with APNASA will provide guidance in the LP turbine Reynolds number research areas to reduce lapse rate. To accurately predict the low Reynolds number flow in the LP turbine is a challenging task for any computational fluid dynamic (CFD) code. The purpose of this study is to evaluate the capability of a CFD code, APNASA, to predict the sensitivity of the Reynolds number in LP turbines.


Author(s):  
Daniel O. Baun ◽  
Ronald D. Flack

Lateral centrifugal impeller forces are calculated using the CFD model developed in Part I of this paper. The impeller forces are evaluated by integrating the pressure and momentum profiles at both the impeller inlet and exit planes. Direct impeller lateral force measurements were made using a magnetic bearing supported pump rotor. Comparisons between the simulated and measured forces are first made for both average and transient impeller forces with water as the working fluid. Air was then substituted as the working fluid in the validated CFD model and the effect of impeller Mach number and Reynolds number on the static impeller lateral forces was investigated. The non-dimensional lateral impeller force characteristics as a function of normalized flow coefficient are similar in character between the incompressible and compressible case. At the matching point flow coefficient the non-dimensional impeller force magnitude was the same for all compressible and incompressible simulations. For any normalized flow rate other than the matching point flow rate, the magnitude of the non-dimensional impeller force increased as the Mach number increased. As the choke condition was approached the magnitude of the impeller force increased exponentially. As the Mach number increased the transition of the force orientation vector from the low flow asymptote to the high flow asymptote occurred over a progressively smaller range of flows.


Sign in / Sign up

Export Citation Format

Share Document