Concept of an Automatic Integration of Parts Measurement Data Into Feature-Based CAD Models

2018 ◽  
Author(s):  
Thiago Weber Martins ◽  
Lars Niemczik ◽  
Reiner Anderl
Keyword(s):  
Measurement Data ◽  
Product Development Process ◽  
Work Piece ◽  
Cad Model ◽  
3D Cad ◽  
Cad System ◽  
Target Values ◽  
Cad Models ◽  
Feature Based ◽  
Sheet Metal Profiles

This paper introduces a concept to integrate measurements data into feature-based 3D CAD models. The concept focuses on its application in the measurement of bifurcated sheet metal profiles. For that, an interface to read and import this data into the CAD system is developed. Since the measurement data is stored as a point cloud, further data processing (reverse engineering) is necessary to recreate the work piece shape in the CAD system. If the measured work piece model and the CAD model of the design piece are available, an automated comparison of the defined dimension takes place. The result is a notification in the CAD model indicating which dimension deviates from the target values. Use-cases are elaborated for integrating the concept in the product development process. To implement this concept, an experimental setup is built up consisting of a measurement system and 3D CAD system. The COPRA ProfileScan Desktop is used to measure the profile. Siemens NX 11 is the chosen CAD system. Based on this setup, the concept is validated on a manufactured profile.

Graph-Based Simplification of Feature-Based Three-Dimensional Computer-Aided Design Models for Preserving Connectivity

2015 ◽  
Vol 15 (3) ◽  
Author(s):  
Soonjo Kwon ◽  
Byung Chul Kim ◽  
Duhwan Mun ◽  
Soonhung Han
Keyword(s):  
Computer Aided Design ◽  
Three Dimensional ◽  
Evaluation Metrics ◽  
Prototype System ◽  
Cad Model ◽  
3D Cad ◽  
Computer Aided ◽  
Cad Models ◽  
Feature Based ◽  
Aided Design

The required level of detail (LOD) of a three-dimensional computer-aided design (3D CAD) model differs according to its purpose. It is therefore important that users are able to simplify a highly complex 3D CAD model and create a low-complexity one. The simplification of a 3D CAD model requires the application of a simplification operation and evaluation metrics for the geometric elements of the 3D CAD model. The evaluation metrics are used to select those elements that should be removed. The simplification operation removes selected elements in order to simplify the 3D CAD model. In this paper, we propose the graph-based simplification of feature-based 3D CAD models using a method that preserves connectivity. First, new evaluation metrics that consider the discrimination priority among several simplification criteria are proposed. Second, a graph-based refined simplification operation that prevents the separation of a feature-based 3D CAD model into multiple volumes is proposed. Finally, we verify the proposed method by implementing a prototype system and performing simplification experiments using feature-based 3D CAD models.

scholarly journals Automatized Evaluation of Students’ CAD Models

2021 ◽  
Vol 11 (4) ◽  
pp. 145
Author(s):  
Nenad Bojcetic ◽  
Filip Valjak ◽  
Dragan Zezelj ◽  
Tomislav Martinec
Keyword(s):  
Computer Aided Design ◽  
Three Dimensional ◽  
Computer Application ◽  
Test Cases ◽  
Cad Model ◽  
Computer Solution ◽  
3D Cad ◽  
Computer Aided ◽  
Cad Models ◽  
Aided Design

The article describes an attempt to address the automatized evaluation of student three-dimensional (3D) computer-aided design (CAD) models. The driving idea was conceptualized under the restraints of the COVID pandemic, driven by the problem of evaluating a large number of student 3D CAD models. The described computer solution can be implemented using any CAD computer application that supports customization. Test cases showed that the proposed solution was valid and could be used to evaluate many students’ 3D CAD models. The computer solution can also be used to help students to better understand how to create a 3D CAD model, thereby complying with the requirements of particular teachers.

A 3D CAD model input pipeline for REFMUL3 full-wave FDTD 3D simulator

2021 ◽  
Vol 16 (11) ◽  
pp. C11013
Author(s):  
J.M. Santos ◽  
E. Ricardo ◽  
F.J. da Silva ◽  
T. Ribeiro ◽  
S. Heuraux ◽  
...  
Keyword(s):  
Vessel Wall ◽  
Thermal Protection ◽  
Interface Problem ◽  
Cad Model ◽  
Fusion Plasma ◽  
3D Cad ◽  
Full Wave ◽  
Wall Structures ◽  
Design Cycle ◽  
Cad Models

Abstract The use of advanced simulation has become increasingly more important in the planning, design, and assessment phases of future fusion plasma diagnostics, and in the interpretation of experimental data from existing ones. The design cycle of complex reflectometry systems, such as the ones being planned for next generation machines (IDTT and DEMO), relies heavily on the results produced by synthetic diagnostics, used for system performance evaluation and prediction, both crucial in the design process decision making. These synthetic diagnostics need realistic representations of all system components to incorporate the main effects that shape their behavior. Some of the most important elements that are required to be well modelled and integrated in simulations are the wave launcher structures, such as the waveguides, tapers, and antennas, as well as the vessel wall structures and access to the plasma. The latter are of paramount importance and are often neglected in this type of studies. Faithfully modelling them is not an easy task, especially in 3D simulations. The procedure herein proposed consists in using CAD models of a given machine, together with parameterizable models of the launcher, to produce a description suited for Finite Difference Time Domain (FDTD) 3D simulation, combining the capabilities of real-world CAD design with the power of simulation. However, CAD model geometric descriptions are incompatible with the ones used by standard FDTD codes. CAD software usually outputs models in a tessellated mesh while FDTD simulators use Volumetric Pixel (VOXEL) descriptions. To solve this interface problem, we implemented a pipeline to automatically convert complex CAD models of tokamak vessel components and wave launcher structures to the VOXEL input required by REFMUL3, a full wave 3D Maxwell FDTD parallel code. To illustrate the full procedure, a complex reflectometry synthetic diagnostic for IDTT was setup, converted and simulated. This setup includes 3 antennas recessed into the vessel wall, for thermal protection, one for transmission and reception, and two just for reception.

Geometric Reasoning for the Coding of CAD Models

1995 ◽  
Author(s):  
A. Z. Qamhiyah ◽  
B. Benhabib ◽  
R. D. Venter
Keyword(s):  
Computer Aided Design ◽  
Feature Recognition ◽  
Effective Means ◽  
Boundary Representation ◽  
Cad Model ◽  
Cad System ◽  
Cad Models ◽  
Form Features ◽  
Feature Based Design ◽  
Design Retrieval

Abstract Many of today’s concurrent product-development cycles depend on the utilization of intelligent Computer-Aided Design (CAD) systems. Thus, it would be essential to provide CAD users with effective means for interacting with the CAD system and its database. This paper addresses the development of a boundary-based coding procedure for CAD models. Coding the geometric and processing characteristics of objects, based on their CAD model representation, has been long recognized as an effective approach that allows convenient design retrieval on the one hand and process-planning automation on the other. Our work is based on the assumption that form features are recognizable and extractable from the CAD model by current feature-recognition, feature extraction and feature-based-design approaches. The coding procedure is applicable to the boundary representation of the object and its extracted form features.

scholarly journals Feature-based translation of CAD models with macro-parametric approach: issues of feature mapping, persistent naming, and constraint translation

2020 ◽  
Vol 7 (5) ◽  
pp. 603-614 ◽  
Author(s):  
Mutahar Safdar ◽  
Tahir Abbas Jauhar ◽  
Youngki Kim ◽  
Hanra Lee ◽  
Chiho Noh ◽  
...  
Keyword(s):  
Computer Aided Design ◽  
Parametric Approach ◽  
Model Data ◽  
Feature Mapping ◽  
Product Model ◽  
Cad Systems ◽  
Cad System ◽  
Cad Models ◽  
Feature Based ◽  
Aided Design

Abstract Feature-based translation of computer-aided design (CAD) models allows designers to preserve the modeling history as a series of modeling operations. Modeling operations or features contain information that is required to modify CAD models to create different variants. Conventional formats, including the standard for the exchange of product model data or the initial graphics exchange specification, cannot preserve design intent and only geometric models can be exchanged. As a result, it is not possible to modify these models after their exchange. Macro-parametric approach (MPA) is a method for exchanging feature-based CAD models among heterogeneous CAD systems. TransCAD, a CAD system for inter-CAD translation, is based on this approach. Translators based on MPA were implemented and tested for exchange between two commercial CAD systems. The issues found during the test rallies are reported and analyzed in this work. MPA can be further extended to remaining features and constraints for exchange between commercial CAD systems.

Toward Effective Mechanical Design Reuse: CAD Model Retrieval Based on General and Partial Shapes

2009 ◽  
Vol 131 (12) ◽  
Author(s):  
Min Li ◽  
Y. F. Zhang ◽  
J. Y. H. Fuh ◽  
Z. M. Qiu
Keyword(s):  
Computer Aided Design ◽  
Mechanical Design ◽  
Three Dimensional ◽  
Cad Model ◽  
Model Retrieval ◽  
Cad Models ◽  
Feature Based ◽  
Novel Method ◽  
Aided Design ◽  
Model Similarity

In product design, a large proportion of three-dimensional (3D) computer-aided design (CAD) models can be reused to facilitate future product development due to their similarities in function and shape. This paper presents a novel method that incorporates modeling knowledge into CAD model similarity assessment to improve the effectiveness of reuse-oriented retrieval. First, knowledge extraction is performed on archived feature-based CAD models to construct feature dependency directed acyclic graph (FDAG). Second, based on the FDAG subgraph decomposition, two useful component partitioning approaches are developed to extract simplified essential shapes and meaningful subparts from CAD models. Third, the extracted shapes and their FDAG subgraphs are indexed. Finally, the indexed shapes that are similar to user-sketched queries are retrieved to reuse, and FDAG information of the retrieved shapes is provided as redesign suggestions. Experimental results suggest that the incorporation of modeling knowledge greatly facilitates CAD model retrieval and reuse. Algorithm evaluations also show the presented method outperforms other 3D retrieval methods.

scholarly journals A multi-user selective undo/redo approach for collaborative CAD systems

2014 ◽  
Vol 1 (2) ◽  
pp. 103-115 ◽  
Author(s):  
Yuan Cheng ◽  
Fazhi He ◽  
Bin Xu ◽  
Soonhung Han ◽  
Xiantao Cai ◽  
...  
Keyword(s):  
Cad Model ◽  
Feature Combination ◽  
Collaborative Systems ◽  
Cad Systems ◽  
Cad System ◽  
Design Error ◽  
Engineering Design Process ◽  
Dependency Relationship ◽  
Cad Models ◽  
Remote Sites

Abstract The engineering design process is a creative process, and the designers must repeatedly apply Undo/Redo operations to modify CAD models to explore new solutions. Undo/Redo has become one of most important functions in interactive graphics and CAD systems. Undo/Redo in a collaborative CAD system is also very helpful for collaborative awareness among a group of cooperative designers to eliminate misunderstanding and to recover from design error. However, Undo/Redo in a collaborative CAD system is much more complicated. This is because a single erroneous operation is propagated to other remote sites, and operations are interleaved at different sites. This paper presents a multi-user selective Undo/Redo approach in full distributed collaborative CAD systems. We use site ID and State Vectors to locate the Undo/Redo target at each site. By analyzing the composition of the complex CAD model, a tree-like structure called Feature Combination Hierarchy is presented to describe the decomposition of a CAD model. Based on this structure, the dependency relationship among features is clarified. B-Rep re-evaluation is simplified with the assistance of the Feature Combination Hierarchy. It can be proven that the proposed Undo/Redo approach satisfies the intention preservation and consistency maintenance correctness criteria for collaborative systems.

Integration of CAD, CAPP and Process Modeling Using XML Technologies

2006 ◽  
Author(s):  
Pravin Khurana ◽  
Dusan N. Sormaz ◽  
Raghunath Khetan
Keyword(s):  
Process Planning ◽  
Process Modeling ◽  
Process Design ◽  
Software Tool ◽  
Cad Model ◽  
Computer Aided ◽  
Cad Models ◽  
Feature Based ◽  
Manufacturing Features

Integration of CAD (Computer Aided Design), CAPP (Computer Aided Process Planning) and Process Modeling activities plays a vital role in enabling concurrent product and process design. Typically each of these functions is performed in its own dedicated software environment. The integration will require interfacing several disconnected processes and software components built in different languages, and platforms. This paper presents an integration methodology, validated using a case study, in which a steering housing was analyzed and its process planning and design tasks were integrated using several software tools. The first integration task was to generate a feature based CAD model (in Unigraphics) and map these design features to a set of manufacturing features. Feature based design was performed using the Horizontal Modeling™ approach developed at Delphi. Features developed using this approach were then mapped to manufacturing features using APPS, a software tool developed at Delphi Dynamics and Propulsion Innovation Center. This task involved interrogation of the geometric CAD model to generate geometric and tolerance information and represent them in a format suitable for feature-based process planning. The second task of integration is generation of feasible “production-intent” process plans. This task is performed using APPS and IMPlanner process planner, a knowledge based software tool developed at Ohio University. The third and final task of integration is automated generation of in-process CAD models. This task involved the integration of Delphi process design techniques to generate CAD models (in Unigraphics) to represent the component at each stage of the manufacturing process. Evaluation of these steps through the case study has identified the strengths and weaknesses of the proposed integration methodology, which is reported in this paper.

A Database Framework for the Characterization and Classification of Parametric Models Based on Complexity Metrics to Support Data Analytics

2019 ◽  
Author(s):  
Jorge D. Camba ◽  
Manuel Contero ◽  
David Pérez-López ◽  
Pedro Company
Keyword(s):  
Data Analytics ◽  
Parametric Models ◽  
Graph Representation ◽  
Report Generation ◽  
Cad System ◽  
Complexity Metrics ◽  
Database Structure ◽  
Cad Models ◽  
Feature Based

Abstract We present a database architecture for exploring, classifying, and visualizing feature-based parametric CAD models based on quantitative complexity metrics. The system consists of (1) an external relational database structure where models are stored along with their graph representation and the numerical values of each complexity metric, (2) a client module that is integrated in the user’s CAD system and facilitates navigation within the repository, and (3) a report generation module that allows exporting CAD complexity data from the external repository to other applications for validation and analysis. In this paper, we justify the need for our system in the context of data analytics and discuss the rationale of its design as well as its architecture and implementations details. Finally, we describe a use case that illustrates the application of our framework in the characterization and evaluation of CAD models.

Sign in / Sign up

Export Citation Format

Share Document