Modified single lap joint (MSLJ) test configuration for the determination of adhesive fracture energy

2005 ◽  
Author(s):  
S. B. Kumar ◽  
I. Sridhar ◽  
S. Sivashanker ◽  
Asim Bag ◽  
S. O. Osiyemi
Keyword(s):  
Fracture Energy ◽  
Lap Joint ◽  
Test Configuration ◽  
Adhesive Fracture ◽  
Single Lap Joint

Mode-I adhesive fracture energy measurement with modified single-lap joint test geometry

2006 ◽  
Vol 20 (10) ◽  
pp. 1109-1124 ◽  
Author(s):  
S. B. Kumar ◽  
I. Sridhar ◽  
S. Sivashanker ◽  
S. O. Osiyemi
Keyword(s):  
Fracture Energy ◽  
Mode I ◽  
Energy Measurement ◽  
Lap Joint ◽  
Adhesive Fracture ◽  
Single Lap Joint ◽  
Test Geometry

In Situ Determination of Glass Transition Temperatures of Epoxy Adhesives in Structural Ceramic Assemblies

2011 ◽  
Vol 62 ◽  
pp. 107-116
Author(s):  
Valérie Nassiet ◽  
Bouchra Hassoune-Rhabbour ◽  
Yves Baziard
Keyword(s):  
Glass Transition ◽  
Thermomechanical Analysis ◽  
Epoxy Adhesive ◽  
Lap Joint ◽  
Scanning Calorimetry ◽  
Experimental Conditions ◽  
Single Lap Joint ◽  
Epoxy Adhesives

A method is described for measuring the glass transition temperature (Tg) of epoxy joints bonding ceramic (SiC) substrates. This method is based on the strain measure of a single-lap joint subjected to a temperature variation. The resulting displacement (d) is observed as a function of the temperature (T) by means of a contact strain gauge extensometer. Thus Tg value can be determined using (d-T) curves recorded. The influence of joint parameters (joint thickness and overlap length) and of other parameters such as the applied load and the surface state of substrates were studied for a structural epoxy adhesive showing different thermomechanical behaviours. The results show that it is possible, with appropriate experimental conditions, to measure Tg with this method and to find Tg values similar to those found by classical techniques such as the static thermomechanical analysis (TMA) and the differential scanning calorimetry (DSC). This method shows similarities with TMA, but it has the advantage to allow the thermomechanical analysis of adhesives without destructive sampling of joints.

Kekuatan Sambungan AL/CFRP Menggunakan Adhesif Epoksi/Serbuk-AL dengan Variasi Pressure Level

2017 ◽  
Vol 1 (1) ◽  
Author(s):  
Bi Asngali
Keyword(s):  
Pressure Level ◽  
Lap Joint ◽  
Single Lap Joint ◽  
Al 2024

 Penelitian ini bertujuan untuk menyelidiki pengaruh pressure level terhadap kekuatan geser sambungan single lap joint (SLJ) antara Al 2024 dan CFRP dengan adesif epoksi/serbuk Al. Variasi pressure level yang digunakan adalah 0,6; 0,7; 0,8; 0,9 dan 1 MPa. Pembuatan dan pengujian spesimen uji geser mengacu pada ASTM D 1002. Hasil penelitian menunjukkan bahwa pressure level dapat meningkatkan kekuatan geser sambungan. Pada variabel pressure level terbaiknya yaitu 0,9 MPa menghasilkan kekuatan geser tertinggi (8,59 MPa). Pada kondisi tersebut, penampang patahan menunjukkan jenis kegagalan kombinasi antara kegagalan cohesive, light fiber tear dan fiber-tear.Kata kunci— pressure level; epoksi/serbuk-Al; kekuatan geser; single lap joint .

Experimental and FEA Evaluation of Hybrid Joint Strength of Single Lap joint

2011 ◽  
Vol 1 (9) ◽  
pp. 93-96
Author(s):  
S. S. Kadam S. S. Kadam ◽  
◽  
P. A. Dixit P. A. Dixit
Keyword(s):  
Joint Strength ◽  
Lap Joint ◽  
Single Lap Joint ◽  
Hybrid Joint

scholarly journals Application of the Point Stress Criterion to Assess the Bond Strength of a Single-Lap Joint

2014 ◽  
Vol 46 (4) ◽  
pp. 518-525
Author(s):  
K. S. Sajikumar ◽  
N. Asok Kumar ◽  
B. Nageswara Rao
Keyword(s):  
Bond Strength ◽  
Lap Joint ◽  
Stress Criterion ◽  
Single Lap Joint

Increasing single-lap joint strength by adherend curvature-induced residual stresses

2013 ◽  
Vol 27 (3) ◽  
pp. 244-251 ◽  
Author(s):  
Ş. Temiz ◽  
S. Akpinar ◽  
M.D. Aydın ◽  
E. Sancaktar
Keyword(s):  
Residual Stresses ◽  
Joint Strength ◽  
Lap Joint ◽  
Single Lap Joint
Sign in / Sign up

Export Citation Format

Share Document