LIFT, a noise-effective low order focal-plane sensor: from theory to full experimental validation

2012 ◽  
Author(s):  
Cédric Plantet ◽  
Benoit Neichel ◽  
Serge Meimon ◽  
Thierry Fusco ◽  
Jean-Marc Conan
2019 ◽  
Vol 488 (3) ◽  
pp. 4307-4316 ◽  
Author(s):  
Olivier Herscovici-Schiller ◽  
Jean-François Sauvage ◽  
Laurent M Mugnier ◽  
Kjetil Dohlen ◽  
Arthur Vigan

Abstract Quasi-static aberrations in coronagraphic systems are the ultimate limitation to the capabilities of exoplanet imagers both ground-based and space-based. These aberrations – which can be due to various causes such as optics alignment or moving optical parts during the observing sequence – create light residuals called speckles in the focal plane. Those speckles might be mistaken for planets. For ground-based instruments, the presence of residual turbulent wavefront errors due to partial adaptive optics correction causes an additional difficulty to the challenge of measuring aberrations in the presence of a coronagraph. In this paper, we present an extension of COFFEE, the coronagraphic phase diversity, to the estimation of quasi-static aberrations in the presence of adaptive-optics-corrected residual turbulence. We perform realistic numerical simulations to assess the performance that can be expected on an instrument of the current generation. We perform the first experimental validation in the laboratory, which demonstrates that quasi-static aberrations can be corrected during the observations by means of coronagraphic phase diversity.


2010 ◽  
Author(s):  
Serge Meimon ◽  
Thierry Fusco ◽  
Frederic Cassaing
Keyword(s):  

Author(s):  
Raphaël Pourcelot ◽  
Mamadou N'Diaye ◽  
Emiel H. Por ◽  
Marshall D. Perrin ◽  
Rémi Soummer ◽  
...  

2013 ◽  
Vol 21 (14) ◽  
pp. 16337 ◽  
Author(s):  
C. Plantet ◽  
S. Meimon ◽  
J.-M. Conan ◽  
T. Fusco

2012 ◽  
Author(s):  
Visa Korkiakoski ◽  
Christoph U. Keller ◽  
Niek Doelman ◽  
Rufus Fraanje ◽  
Raluca Andrei ◽  
...  

2015 ◽  
Vol 127 (955) ◽  
pp. 857-869 ◽  
Author(s):  
Garima Singh ◽  
Julien Lozi ◽  
Olivier Guyon ◽  
Pierre Baudoz ◽  
Nemanja Jovanovic ◽  
...  

2010 ◽  
Vol 35 (18) ◽  
pp. 3036 ◽  
Author(s):  
Serge Meimon ◽  
Thierry Fusco ◽  
Laurent M. Mugnier

2017 ◽  
Vol 2017 ◽  
pp. 1-12
Author(s):  
Ying Zhao ◽  
Jiahao Chen ◽  
Qiang Zhou ◽  
Xiaohan Jia ◽  
Xueyuan Peng

The low-order vibration modes of a reciprocating compressor were studied by means of numerical simulation and experimental validation. A shell element model, a beam element model, and two solid element models were established to investigate the effects of bolted joints and element types on low-order vibration modes of the compressor. Three typical cases were compared to check the effect of locations of moving parts on the vibration modes of the compressor. A forced modal test with the MRIT (Multiple References Impact Test) technique was conducted to validate the simulation results. Among four numerical models, the solid element model with the bolt-pretension method showed the best accuracy compared with experimental data but the worst computational efficiency. The shell element model is recommended to predict the low-order vibration modes of the compressor with regard to effectiveness and usefulness. The sparsely distributed bolted joints with a small bonded region on the contact surface were key bolted joints that had greater impacts on the low-order vibration modes of the compressor than the densely distributed bolted joints. The positions of the moving parts had little effect on the low-order vibration modes of the compressor.


Sign in / Sign up

Export Citation Format

Share Document