scholarly journals Comparison of two-dimensional axial-symmetric and longitudinally invariant methods for three-dimensional shallow water acoustic propagation using finite element methods

2013 ◽  
Author(s):  
Benjamin M. Goldsberry ◽  
Marcia Isakson
Keyword(s):  
Finite Element ◽  
Shallow Water ◽  
Finite Element Methods ◽  
Three Dimensional ◽  
Acoustic Propagation ◽  
Two Dimensional

Optimum Design for the Frame of Open Type Abrasive Flow Polish Machine

2012 ◽  
Vol 497 ◽  
pp. 89-93
Author(s):  
Liang Liang Yuan ◽  
Ke Hua Zhang ◽  
Li Min
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Finite Element Methods ◽  
Optimization Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Force Model ◽  
Optimization Analysis ◽  
Open Type ◽  
Set Up

In order to process heterotype hole of workpiece precisely, an open abrasive flow polish machine is designed, and the optimization design of machine frame is done for low cost. Firstly, basing on the parameters designed with traditional ways, three-dimensional force model is set up with the soft of SolidWorks. Secondly, the statics and modal analysis for machine body have been done in Finite element methods (FEM), and then the optimization analysis of machine frame has been done. At last, the model of rebuild machine frame has been built. Result shows that the deformation angle value of machine frame increased from 0.72′ to 1.001′, the natural frequency of the machine decreased from 75.549 Hz to 62.262 Hz, the weight of machine decreased by 74.178 Kg after optimization. It meets the strength, stiffness and angel stiffness requirement of machine, reduces the weight and cost of machine.

Aerodynamic study of three-dimensional larynx models using finite element methods

2008 ◽  
Vol 311 (1-2) ◽  
pp. 39-55 ◽  
Author(s):  
Marcelo de Oliveira Rosa ◽  
José Carlos Pereira
Keyword(s):  
Finite Element ◽  
Finite Element Methods ◽  
Three Dimensional

Consistent Hydrodynamic Mass for Parallel Prismatic Beams in a Fluid-Filled Container

1984 ◽  
Vol 106 (3) ◽  
pp. 270-275
Author(s):  
J. F. Loeber
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Incompressible Fluid ◽  
Finite Element Methods ◽  
Mass Matrix ◽  
Three Dimensional ◽  
Beam Length ◽  
Step Process ◽  
Beam Bending

In this paper, representation of the effects of incompressible fluid on the dynamic response of parallel beams in fluid-filled containers is developed using the concept of hydrodynamic mass. Using a two-step process, first the hydrodynamic mass matrix per unit (beam) length is derived using finite element methods with a thermal analogy. Second, this mass matrix is distributed in a consistent mass fashion along the beam lengths in a manner that accommodates three-dimensional beam bending plus torsion. The technique is illustrated by application to analysis of an experiment involving vibration of an array of four tubes in a fluid-filled cylinder.

Three-Dimensional Computations of Transport and Growth for Crystal Growth Systems

2000 ◽  
Author(s):  
Jeffrey J. Derby ◽  
Andrew Yeckel
Keyword(s):  
Finite Element ◽  
Crystal Growth ◽  
Finite Element Methods ◽  
Three Dimensional ◽  
Bulk Crystal ◽  
Time Dependent ◽  
Engineering Systems ◽  
Bulk Crystal Growth ◽  
Strongly Nonlinear ◽  
Parallel Supercomputers

Abstract Modern finite element methods implemented on parallel supercomputers promise to allow the study of three-dimensional, time-dependent continuum phenomena in many engineering systems. This paper shows several examples of the fruitful application of these approaches to bulk crystal growth systems, where strongly nonlinear coupled phenomena are important.

Inclusion of Local Shell Behavior of Tubes Into a Two-Dimensional Beam Approximation of Deformation in Nuclear Fuel Channels

2002 ◽  
Author(s):  
S. Khajehpour ◽  
R. G. Sauve´ ◽  
N. Badie
Keyword(s):  
Finite Element ◽  
Contact Stiffness ◽  
Three Dimensional ◽  
Local Deformation ◽  
Beam Model ◽  
Two Dimensional ◽  
Dimensional Modeling ◽  
Dimensional Finite Element ◽  
Nonlinear Force ◽  
Three Dimensional Finite Element

A method has been developed to incorporate the local three-dimensional shell behavior of two concentric tubes in the two-dimensional beam modeling of the problem. The two dimensional modeling of fuel channels in CANDU pressurized heavy water nuclear reactors is used in lieu of a more accurate three dimensional finite element approach in order to reduce the on-line simulation time which greatly affects the SLAR (Spacer Location And Repositioning) maintenance operation cost during outage. However, effort must be made to include the three-dimensional shell behavior of these channels into the two-dimensional modeling. In recent studies a nonlinear force-dependent model for contact stiffness between the calandria tube and pressure tube has been developed. However, local deformation of calandria the tube at spacer locations due to in-reactor creep leads to settling of the spacer into the calandria tube that consequently reduces the gap between the two tubes. In this work, the effect of local deformation (elastic and creep) of calandria tubes on modeling of contact at spacer locations is assessed using a three dimensional finite element code. The result is incorporated into a two-dimensional beam model of the problem as a reduction in size of the spacers that separate the two tubes. It is shown that the proposed method increases the accuracy of prediction of contact time and the spacer. In general, the method described in this paper suggests a way to incorporate local shell deformation into beam models of slender shell structure.

Sign in / Sign up

Export Citation Format

Share Document