0615 Separation Control of High-performance Airfoil under Low Reynolds Number Condition by DBD Plasma Actuator

2015 ◽  
Vol 2015 (0) ◽  
pp. _0615-1_-_0615-2_
Author(s):  
Akira Matsubara ◽  
Satoshi Sekimoto ◽  
Taufik Sulaiman ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
...  
Keyword(s):  
Reynolds Number ◽  
High Performance ◽  
Low Reynolds Number ◽  
Plasma Actuator ◽  
Separation Control ◽  
Dbd Plasma ◽  
Low Reynolds

Experimental Comparison of DBD Plasma Actuators for Low Reynolds Number Separation Control

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Christopher R. Marks ◽  
Rolf Sondergaard ◽  
Mitch Wolff ◽  
Rich Anthony
Keyword(s):  
Reynolds Number ◽  
Low Reynolds Number ◽  
Turbine Blades ◽  
Plasma Actuators ◽  
Experimental Comparison ◽  
Separation Control ◽  
Suction Surface ◽  
Dbd Plasma ◽  
Low Reynolds ◽  
Low Reynolds Number Airfoil

This paper presents experimental work comparing several Dielectric Barrier Discharge (DBD) plasma actuator configurations for low Reynolds number separation control. Actuators studied here are being investigated for use in a closed loop separation control system. The plasma actuators were fabricated in the U.S. Air Force Research Laboratory Propulsion Directorate’s thin film laboratory and applied to a low Reynolds number airfoil that exhibits similar suction surface behavior to those observed on Low Pressure (LP) Turbine blades. In addition to typical asymmetric arrangements producing downstream jets, one electrode configurations was designed to produce an array of off axis jets, and one produced a spanwise array of linear vertical jets in order to generate vorticity and improved boundary layer to freestream mixing. The actuators were installed on an airfoil and their performance compared by flow visualization, surface stress sensitive film (S3F), and drag measurements. The experimental data provides a clear picture of the potential utility of each design. Experiments were carried out at four Reynolds numbers, 1.4 × 105, 1.0 × 105, 6.0 × 104, and 5.0 × 104 at a-1.5 deg angle of attack. Data was taken at the AFRL Propulsion Directorate’s Low Speed Wind Tunnel (LSWT) facility.

scholarly journals S052034 Multi-Objective Design Exploration of DBD Plasma Actuator for Low Reynolds Number Application

2013 ◽  
Vol 2013 (0) ◽  
pp. _S052034-1-_S052034-5
Author(s):  
Taufik SULAIMAN ◽  
Makoto SATO ◽  
Satoshi SEKIMOTO ◽  
Taku NONOMURA ◽  
Akira Oyama ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Low Reynolds Number ◽  
Plasma Actuator ◽  
Dbd Plasma ◽  
Design Exploration ◽  
Multi Objective ◽  
Low Reynolds

Experimental Comparison of DBD Plasma Acuators for Low Reynolds Number Separation Control

2011 ◽  
Author(s):  
Christopher Marks ◽  
Rolf Sondergaard ◽  
Mitch Wolff ◽  
Rich Anthony
Keyword(s):  
Reynolds Number ◽  
Low Reynolds Number ◽  
Turbine Blades ◽  
Experimental Comparison ◽  
Separation Control ◽  
Suction Surface ◽  
Dbd Plasma ◽  
Low Reynolds ◽  
Low Reynolds Number Airfoil ◽  
Lp Turbine

This paper presents experimental work comparing several Dielectric Barrier Discharge (DBD) plasma actuator configurations for low Reynolds number separation control. Actuators studied here are being investigated for use in a closed loop separation control system. The plasma actuators were fabricated in the U. S. Air Force Research Laboratory Propulsion Directorate’s thin film laboratory and applied to a low Reynolds number airfoil that exhibits similar suction surface behavior to those observed on Low Pressure (LP) Turbine blades. In addition to typical asymmetric arrangements producing downstream jets, one electrode configurations was designed to produce an array of off axis jets, and one produced a spanwise array of linear vertical jets in order to generate vorticity and improved boundary layer to freestream mixing. The actuators were installed on an airfoil and their performance compared by flow visualization, surface stress sensitive film (S3F), and drag measurements. The experimental data provides a clear picture of the potential utility of each design. Experiments were carried out at four Reynolds numbers, 1.4×105, 1.0 × 105, 6.0 × 104, and 5.0 × 104 at a −1.54° angle of attack. Data was taken at the AFRL Propulsion Directorate’s Low Speed Wind Tunnel (LSWT) facility.

On High-Performance Airfoil at Very Low Reynolds Number

2016 ◽  
Vol 28 (3) ◽  
pp. 273-285
Author(s):  
Katsuya Hirata ◽  
◽  
Ryo Nozawa ◽  
Shogo Kondo ◽  
Kazuki Onishi ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
High Performance ◽  
Low Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Slow Flow ◽  
Low Reynolds Numbers ◽  
Low Reynolds

[abstFig src='/00280003/02.jpg' width=""300"" text='Iso-Q surfaces of very-slow flow past an iNACA0015' ] The airfoil is often used as the elemental device for flying/swimming robots, determining its basic performances. However, most of the aerodynamic characteristics of the airfoil have been investigated at Reynolds numbers Re’s more than 106. On the other hand, our knowledge is not enough in low Reynolds-number ranges, in spite of the recent miniaturisation of robots. In the present study, referring to our previous findings (Hirata et al., 2011), we numerically examine three kinds of high-performance airfoils proposed for very-low Reynolds numbers; namely, an iNACA0015 (the NACA0015 placed back to front), an FPBi (a flat plate blended with iNACA0015 as its upper half) and an FPBN (a flat plate blended with the NACA0015 as its upper half), in comparison with such basic airfoils as a NACA0015 and an FP (a flat plate), at a Reynolds number Re = 1.0 × 102 using two- and three-dimensional computations. As a result, the FPBi shows the best performance among the five kinds of airfoils.

Sign in / Sign up

Export Citation Format

Share Document