112 Elastic Analysis of Cylindrical Shells by the Finite Element Method : The Case of Oil Tank under Wind Load

2000 ◽  
Vol 2000.40 (0) ◽  
pp. 24-25
Author(s):  
Seiichi OHTAKI ◽  
Akinobu KURIMURA ◽  
Kazuya KATADA
1999 ◽  
Vol 21 (2) ◽  
pp. 116-128
Author(s):  
Pham Thi Toan

In the present paper, the goffered multilayered composite cylindrical shells is directly calculated by finite element method. Numerical results on displacements, internal forces and moments are obtained for various kinds of external loads and different boundary conditions.


2007 ◽  
Vol 3 (1) ◽  
Author(s):  
Edela Puricelli ◽  
Jun Sérgio Ono Fonseca ◽  
Marcel Fasolo de Paris ◽  
Hervandil Sant'Anna

2000 ◽  
Author(s):  
A. A. Lakis ◽  
A. Selmane ◽  
C. Dupuis

Abstract A theory is presented to predict the influence of non-linearities associated with the wall of the shell and with the fluid flow on the dynamic of elastic, thin, orthotropic open and closed cylindrical shells submerged and subjected to an internal and external fluid. The open shells are assumed to be freely simply-supported along their curved edges and to have arbitrary straight edge boundary conditions. The method developed is a hybrid of thin shell theory, fluid theory and the finite element method. The solution is divided into four parts. In part one, the displacement functions are obtained from Sanders’ linear shell theory and the mass and linear stiffness matrices for the empty shell are obtained by the finite element procedure. In part two, the modal coefficients derived from the Sanders-Koiter non-linear theory of thin shells are obtained for these displacement functions. Expressions for the second and third order non-linear stiffness matrices of the empty shell are then determined through the finite element method. In part three a fluid finite element is developed, the model requires the use of a linear operator for the velocity potential and a linear boundary condition of impermeability. With the non-linear dynamic pressure, we develop in the fourth part three non-linear matrices for the fluid. The non-linear equation of motion is then solved by the fourth-order Runge-Kutta numerical method. The linear and non-linear natural frequency variations are determined as a function of shell amplitudes for different cases.


Author(s):  
Kotur S. Raghavan

ASME’s Boiler and Pressure Vessel Codes have a history of over one hundred years. The codes have been evolving over time with continuous revisions, improvements and refinements. A major milestone has been the incorporation of “Design by Analysis (DBA)” guidelines about fifty years back (for instance Sec. VIII, Division 2). These were introduced as it was recognized that the prevailing Design by Rules (Section VIII, Division 1) tended to be somewhat over-conservative. The essence of DBA guidelines consists of evaluating the elastic stresses at critical locations and checking the same against the allowable. The allowable happen to functions of the nature of stress distribution and the nature of load. A given stress could be of membrane, bending or peak category and also be either primary or secondary. At the time of appearance of the DBA guidelines, the state of the art of stress analysis was not well advanced and the finite element method was just getting developed. As of today, however, the finite element method has reached a high level of maturity and is very widely used. The latest edition (2010) has recognized this and it contains modeling and post-processing guidelines applicable to FE analysis. This edition also recommends the use of one of three possible approaches. The first is the elastic analysis and classification and categorization of stresses with guidelines regarding how to deal with two- and three-dimensional situations. The other two options are provided to take care of situations wherein the categorization process may lead to either uncertainty or ambiguity. These involve nonlinear analysis either by way of Limit-Load method or Elastic-Plastic Stress Analysis. In either approach the analyst will look for the loads at which there is an onset of gross plastic flow. In the present paper an attempt is made to evaluate the latest DBA guidelines from design application point of view. The purpose is to assess the limitations of the elastic analysis approach. Studies are undertaken to focus typically on the following aspects: 1. Two dimensional problems involving symmetry or axisymmetry. There are situations in which the “bending” stresses are liable to be misinterpreted. 2. Three dimensional problems with emphasis on the assessment of bending stress as categorization in 3D situations is a real challenge 3. General situations involving the secondary stresses. The allowable stress limit for secondary stress is somewhat arbitrary and perhaps very conservative. The studies tend to suggest that the nonlinear route is to be adopted as it is reliable and accounts for many uncertainties associated with the elastic approach.


Sign in / Sign up

Export Citation Format

Share Document