Optimal mechanical and gas permeation properties of polypropylene-organically modified montmorillonite (PP-OMMT) nanocomposites

2014 ◽  
Vol 34 (6) ◽  
pp. 501-509 ◽  
Author(s):  
Youssef Al Herz ◽  
Chandra Mouli R. Madhuranthakam ◽  
Ali Elkamel ◽  
Vikas Mittal
Keyword(s):  
Regression Models ◽  
Primary Objective ◽  
Gas Permeation ◽  
Objective Functions ◽  
Modified Montmorillonite ◽  
Organically Modified Montmorillonite ◽  
Organically Modified ◽  
The Cost ◽  
Permeation Properties

Abstract This article focuses on obtaining optimal mechanical properties of polypropylene-organically modified montmorillonite (PP-OMMT) nanocomposites for different objectives using simulations. The primary objective was to minimize the cost of the PP-OMMT nanocomposites. The other aim was to obtain specific desired properties of the nanocomposite (irrespective of the nanocomposite cost). The later simulation results are useful in designing products where quality of the nanocomposite cannot be compromised (while the cost of the PP-OMMT is secondary). The properties that were optimized include Young’s modulus and oxygen permeation. Regression models were obtained and used to predict these properties as functions of corresponding compositions of the composites. Further, optimization procedures were simulated using these models along with other constraints and objective functions. All simulations were programmed using MATLAB version 7.10.0 (R2010a).

Biodegradable Polyester / Layered Silicate Nanocomposites

2002 ◽  
Vol 740 ◽  
Author(s):  
Pralay Maiti ◽  
Carl A. Batt ◽  
Emmanuel P. Giannelis
Keyword(s):  
Mechanical Properties ◽  
Storage Modulus ◽  
Layered Silicate ◽  
Layered Silicates ◽  
Melt Extrusion ◽  
Biodegradable Polyester ◽  
Modified Montmorillonite ◽  
Organically Modified Montmorillonite ◽  
Silicate Nanocomposites ◽  
Organically Modified

ABSTRACTNanocomposites of α-hydroxy polyester, polylactide (PLA) and β-hydroxy polyester, polyhydroxybutyrate (PHB) with layered silicates have been successfully prepared by melt extrusion of PLA and PHB with organically modified montmorillonite (MMT) and fluoromica. The mechanical properties of the nanocomposites are improved compared to the neat polymers. Storage modulus increase up to 40% compared with the pure polymers by adding only 2–3 wt% nanoclay. Biodegradation can be controlled by the choice of the nanoclay used.

Thermal characterization of organically modified montmorillonite

2001 ◽  
Vol 367-368 ◽  
pp. 339-350 ◽  
Author(s):  
Wei Xie ◽  
Zongming Gao ◽  
Kunlei Liu ◽  
Wei-Ping Pan ◽  
Richard Vaia ◽  
...  
Keyword(s):  
Thermal Characterization ◽  
Modified Montmorillonite ◽  
Organically Modified Montmorillonite ◽  
Organically Modified

Optimisation of the ceramic-like body for ceramifiable EVA-based composites

2017 ◽  
Vol 24 (4) ◽  
pp. 599-607 ◽  
Author(s):  
Xinhao Gong ◽  
Tingwei Wang
Keyword(s):  
Ceramic Body ◽  
Ethylene Vinyl Acetate ◽  
Melt Blending ◽  
Red Phosphorus ◽  
X Ray Diffraction ◽  
Modified Montmorillonite ◽  
Organically Modified Montmorillonite ◽  
Organically Modified ◽  
Dense Ceramic ◽  
Acetate Copolymer

AbstractVarious ceramifiable ethylene-vinyl acetate copolymer (EVA) composites were prepared by melt blending with two kinds of glass frits, organically modified montmorillonite (OMMT) and whitened and capsulised red phosphorus (WCRP). The influence of different filler components and firing temperatures on the ceramifiable properties of the composites was studied. The dripping behaviour of the composites was analyzed by a vertical burning test. The microstructure of the residues was characterised by X-ray diffraction (XRD) and scanning electron microscopy. The results showed that the optimised EVA composite was free of melt dripping during burning with the addition of OMMT. A dimensionally stable and dense ceramic residue was also obtained, especially with the addition of WCRP. It was suggested that new phases were formed at firing temperatures, and WCRP could promote the formation of ceramic body which was not fused during firing at 900°C as evidenced by XRD.

scholarly journals Colorless and Transparent Copolyimides and Their Nanocomposites: Thermo-Optical Properties, Morphologies, and Gas Permeabilities

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 585 ◽  
Author(s):  
Hyeon Shin ◽  
Young-Je Kwark ◽  
Jin-Hae Chang
Keyword(s):  
Optical Properties ◽  
Coefficient Of Thermal Expansion ◽  
Amic Acid ◽  
Gas Permeation ◽  
Molar Ratio ◽  
Molar Ratios ◽  
Thermal Imidization ◽  
Organically Modified ◽  
Permeation Properties

A series of linear aromatic copolyimides (Co-PIs) were synthesized by reacting 4,4′-biphthalic anhydride (BPA) with various molar contents of 2,2′-bis(trifluoromethyl)benzidine (TFB) and p-xylylenediamine (p-XDA) in N,N′-dimethylacetamide (DMAc). Co-PI films were fabricated by solution casting and thermal imidization with poly(amic acid) (PAA) on glass plates. The thermo-optical properties and gas permeabilities of Co-PI films composed of various molar ratios of p-XDA (0.2–1.0 relative to BPA) were investigated. Thermal properties were observed to deteriorate with increasing p-XDA concentration. However, oxygen-transmission rates (O2TRs) and optical transparencies improved with increasing p-XDA concentration. Co-PI hybrids with a 1:0.2:0.8 molar ratio of BPA:TFB:p-XDA and organically modified hectorite (STN) were prepared by the in situ intercalation method. The morphologies and the thermo-optical and gas permeation properties of the hybrids were examined as functions of STN loading (5–50 wt %). XRD and TEM revealed substantial increases in clay particle agglomeration in the Co-PI hybrid films as the clay loading was increased from 5 to 50 wt %. The coefficient of thermal expansion (CTE) and the O2TR of a Co-PI hybrid film were observed to improve with increasing STN concentration; however, its optical transparency decreased gradually with increasing STN concentration.

Sign in / Sign up

Export Citation Format

Share Document