Environmental effects on mode II fracture toughness of unidirectional E-glass/vinyl ester laminated composites

In this article, mode II fracture toughness ( G IIc {G}_{\text{IIc}} ) of unidirectional E-glass/vinyl ester composites subjected to sulfuric acid aging is studied at two different temperatures (25 and 90°C). Specimens were manufactured using the hand lay-up method with the [ 0 ] 20 {{[}0]}_{20} stacking sequence. To study the effects of environmental conditions, samples were exposed to 30 wt% sulfuric acid at room temperature (25°C) for 0, 1, 2, 4, and 8 weeks. Some samples were also placed in the same solution but at 90°C and for 3, 6, 9, and 12 days to determine the interlaminar fracture toughness at different aging conditions. Fracture tests were conducted using end notched flexure (ENF) specimens according to ASTM D7905. The results obtained at 25°C showed that mode II fracture toughness increases for the first 2 weeks of aging and then it decreases for the last 8 weeks. It was also found that the flexural modulus changes with the same trend. Based on the results of the specimens aged at 90°C, a sharp drop in fracture toughness and flexural modulus with a significant decrease in maximum load have been observed due to the aging. Finite element simulations were performed using the cohesive zone model (CZM) to predict the global response of the tested beams.

Flexural bearing capacity and failure mechanism of CFRP-aluminum laminate beam with double-channel cross-section

In this study, the flexural bearing capacity and failure mechanism of carbon fiber-reinforced aluminum laminate (CARALL) beams with a double-channel cross-section and a 3/2 laminated configuration were experimentally and numerically studied. Two types of specimens using different carbon fiber layup configurations ([0°/90°/0°]3 and [45°/0°/−45°]3) were fabricated using the pressure molding thermal curing forming process. The double-channel CARALL beams were subjected to static three-point bending tests to determine their failure behaviors in terms of ultimate bearing capacity and failure modes. Owing to the shortcomings of the two-dimensional Hashin failure criterion, the user-defined FORTRAN subroutine VUMAT suitable for the ABAQUS/Explicit solver and an analysis algorithm were established to obtain a progressive damage prediction of the CFRP layer using the three-dimensional Hashin failure criterion. Various failure behaviors and mechanisms of the CARALL beams were numerically analyzed. The results indicated that the numerical simulation was consistent with the experimental results for the ultimate bearing capacity and final failure modes, and the failure process of the double-channel CARALL beams could be revealed. The ultimate failure modes of both types of double-channel CARALL beams were local buckling deformation at the intersection of the upper flange and web near the concentrated loading position, which was mainly caused by the delamination failure among different unidirectional plates, tension and compression failure of the matrix, and shear failure of the fiber layers. The ability of each fiber layer to resist damage decreased in the order of 90° fiber layer > 0° fiber layer > 45° fiber layer. Thus, it is suggested that 90°, 0°, and 45° fiber layers should be stacked for double-channel CARALL beams.

Influence of technical parameters on the structure of annular axis braided preforms

A modified vertical braiding machine and closed annular axis mandrels with a special-shaped cross section were used to braid annular axis preforms under four different technical parameters. After measuring the braiding angles and yarn spacing of the braided preform in different areas of the mandrels, it was found that the braiding angle increased by 20.9% and the yarn spacing decreased by 19.8% when the speed of the yarn carrier was doubled. The braiding angle decreased by 31.1% and the yarn spacing increased by 28.6% when the rotation speed of the mandrels was doubled. The results show that the rotation speed of the mandrel has a slightly greater influence on the braiding angle and the yarn spacing. By using the modified braiding machine to braid the annular axis preforms, multi-layer continuous braided preforms can be achieved on compact equipment. And the structure of the annular axis braided preforms can be changed by changing the technical parameters.

Analysis of the influence of asymmetric geological conditions on stability of high arch dam

Geological conditions play a decisive role in the stability of arch dam engineering, and the asymmetric geological conditions of the abutment have a very negative impact on the safety of the arch dam. This article takes Lizhou arch dam as the research object, and determines that the arch dam is preliminarily affected by the geological asymmetric characteristics. Through the geomechanical model test method, the overload failure test of the Lizhou arch dam was carried out, and the resistance body, the instability deformation of the structural plane of the two dam abutments, and the influence of each structural plane on the dam body are obtained, and the safety factor is determined. According to the test results under the condition of asymmetric foundation of arch dam, for the structural plane which affects the geological asymmetry of the arch dam, the corresponding reinforcement measures are carried out. The feasibility of the reinforcement scheme is verified by the finite element method, and the safety factor after reinforcement is obtained. According to the results, it is suggested that some engineering measures can be taken to reduce the geological asymmetry between the two banks and ensure the safe and stable operation of the arch dam in the future.

Characterization and Comparison Research on Composite of Alluvial Clayey Soil Modified with Fine Aggregates of Construction Waste and Fly Ash

Fine aggregates of construction waste and fly ash were selected as additives to modify the characteristics of Shanghai clayey soil as a composite. The laboratory tests on consistency index, maximum dry density, and unconfined compressive strength were carried out mainly for the purpose of comparing the modifying effect on the composite from fine aggregates of construction waste with that from fly ash. It is mainly concluded from test results that the liquid and plastic limit of the composites increase with the content of two additives. But their maximum dry density all decreases with the additive content. However, fine aggregates of construction waste can increase the optimum water content of the composites, while fly ash on the contrary. Finally, although the two additive all can increase the unconfined compressive strength of composites, fly ash has better effect. The current conclusions are also compared with previous studies, which indicates that the current research results are not completely the same as those from other researchers.

Material-removing machining wastes as a filler of a polymer concrete (industrial chips as a filler of a polymer concrete)

The paper presents an impact of the addition of industrial machining chips on the mechanical properties of polymer concrete. As an additional filler, six types of industrial waste machining chips were used: steel fine chips, steel medium chips, steel thick chips, aluminium fine chips, aluminium medium chips, and titanium fine chips. During the research, the influence of the addition of chips on the basic parameters of mechanical properties, i.e., tensile strength, compressive strength, splitting tensile strength, and Young’s modulus, was analyzed. On the basis of the obtained results, conclusions were drawn that the addition of chips from machining causes a decrease in the value of the mechanical properties parameters of the polymer concrete even by 30%. The mechanism of cracking of samples, which were subjected to durability tests, was also explored. In addition, it was found that some chip waste can be used as a substitute for natural fillers during preparation of a mineral cast composition without losing much of the strength parameters.

An investigation on the degradation behaviors of Mg wires/PLA composite for bone fixation implants: influence of wire content and load mode

Poly-lactic acid based biocomposite strengthened with magnesium alloy wires (Mg wires/PLA composite) is prepared for bone fixation implantation. The influence of wire content and load mode on the degradation performances of the composite and its components is studied. The result suggests the degradation of Mg wires could slow down the pH decrease originated from the degradation of PLA, while a relatively high wire content contributes to descend the degradation rate of Mg wire in the composite. Dynamic load significantly promotes the mechanical loss of the specimens. After 30 days immersion, the Sb retention is about 65%, 52% and 55%, respectively for pure PLA, the composite at 10 vol% and 20 vol% under dynamic load, comparing to 75%, 70% and 72% under no load. Moreover, dynamic load could further mitigate the degradation of Mg wires by increasing convective transport of acidic products out of the composite.

Investigation of the influence of recyclate content on Poisson number of composites

Composite materials are used in many industries. Their mechanical and physical properties as well as their low weight make them suitable for use in many constructions. Their wide application generates a problem with their disposal. Therefore, it is necessary to design new materials based on waste from polyester–glass laminates in order to introduce a closed circuit in the composite production process. The article presents research aimed at determining solid material composites with polyester–glass recyclate, in order to use these materials for modeling the structure. The aim of this study was to determine the effect of the addition of recyclate to the polyester–glass composite on the deformation and the value of the Poisson number of the material. During the study, samples from composites with the addition of polyester–glass recyclate were used. Samples made in accordance with the standard for plastics PN-EN ISO 527-4_2000P were subjected to static tensile test on a universal testing machine, with variable load parameters. During the test, the longitudinal and transverse elongations of the samples were measured using a strain gauge measuring system. On the basis of the measurements, the values of Poisson numbers were determined, which allowed for a preliminary assessment of the impact of the recyclate content in the composite on its deformability.

Analysis and optimization of mechanical properties of recycled concrete based on aggregate characteristics

The most significant difference between recycled and natural concretes lies in aggregates. The performance of recycled coarse aggregates directly affects the characteristics of recycled concrete. Therefore, an in-depth study of aggregate characteristics is of great significance for improving the quality of recycled concrete. Based on the coarse aggregate content, maximum aggregate size, and aggregate shape, this study uses experiments, theoretical analysis, and numerical simulation to reveal the impact of aggregate characteristics on the mechanical properties of recycled concrete. In this study, we selected the coarse aggregate content, maximum aggregate size, and the aggregate shape as design variables to establish the regression equations of the peak stress and elastic modulus of recycled concrete using the response surface methodology. The results showed that the peak stress and elastic modulus of recycled concrete reach the best when the coarse aggregate content is 45%, the maximum coarse aggregate size is 16 mm, and the regular round coarse aggregates occupy 75%. Such results provide a theoretical basis for the resource utilization and engineering design of recycled aggregates.