Boiling Liquid Expanding Vapor Explosions (BLEVE): Possible Failure Mechanisms

2009 ◽  
pp. 112-112-21 ◽  
Author(s):  
JES Venart
Author(s):  
Juan C. Ramirez ◽  
Suzanne A. Smyth ◽  
Russell A. Ogle

A boiling liquid, expanding vapor explosion (BLEVE) occurs when a pressure vessel containing a superheated liquid undergoes a catastrophic failure, resulting in a violent vaporization of the liquid. The exposure of a pressure vessel to a fire is a classic scenario that can result in a BLEVE. The thermomechanical exergy of a pressure vessel’s contents provides — by definition — an upper bound on the work that can be performed by the system during the explosion. By fixing the values of ambient pressure and temperature (i.e., the dead state), exergy can be interpreted as another thermodynamic property. This rigorous and unambiguous definition makes it ideal to estimate the maximum energy of explosions. The numerical value of exergy depends on the definition of the dead state. In this paper we examine the effect of different definitions for the dead state on the explosion energy value. We consider two applications of this method: the contribution of the vapor head-space to the explosive energy as a function of the fractional liquid fill of the vessel, and the effect of the vessel burst pressure.


Author(s):  
Delphine Laboureur ◽  
Jean-Marie Buchlin ◽  
Patrick Rambaud

The most dangerous accident that can occur in LPG storage is the boiling liquid expanding vapor explosion (BLEVE). To better understand the rupture of the reservoir and the blast wave characteristics, small scale BLEVE experiments are performed with cylinders of 95 ml, filled at 86% with propane, laid horizontally and heated from below. A weakening of the reservoirs on the upper part allows better reproducibility of the rupture. High speed visualization, blast overpressure and surface reservoir temperature are measured. Internal pressure measurement shows that the rupture pressure and temperature are well above the critical point. The fluid is then supercritical and there is no distinction anymore between liquid and gas prior rupture. This kind of reservoir rupture is significant of a new type of BLEVE, a supercritical BLEVE. The experiments also show that the fluid behavior during rupture differs with the size of the weakened part and therefore with the rupture pressure. Finally, the measured peak overpressures are compared with literature models.


1997 ◽  
Vol 119 (3) ◽  
pp. 365-373 ◽  
Author(s):  
D. J. Kielec ◽  
A. M. Birk

A series of fire tests were conducted to study the thermal rupture of propane tanks. The tests involved 400-L ASME automotive propane tanks filled to 80 percent capacity with commercial propane. The tanks were brought to failure using torches and pool fires. The resulting thermal ruptures varied in severity from minor fissures, measuring a few centimeters in length, to catastrophic failures where the tank was flattened on the ground. The catastrophic failures would typically be called boiling liquid expanding vapor explosions (BLEVEs). The objective of this work was to develop a correlation between the failure severity and the tank condition at failure. The deformed propane tanks were measured in detail and the extent of deformation was quantified. The tank failure severity was found to be a complex function of a number of tank and lading properties at failure. This paper presents the measured data from the tanks and a step-by-step description of how the correlation was determined.


Author(s):  
Harry S. Dixon

A fourth case confirms that the explosions are BLEVEs (Boiling Liquid Expanding Vapor Explosions) rather than hydrogen explosions. There are approximately 15,300 explosions annually in the U.S. with attendant spouting acid electrolyte or flying solid parts that cause injuries. It is recommended that temperature sensitive fuses or a circuit breaker be incorporated in the battery to prevent these BLEVE accidents.


Author(s):  
Jin Young Kim ◽  
R. E. Hummel ◽  
R. T. DeHoff

Gold thin film metallizations in microelectronic circuits have a distinct advantage over those consisting of aluminum because they are less susceptible to electromigration. When electromigration is no longer the principal failure mechanism, other failure mechanisms caused by d.c. stressing might become important. In gold thin-film metallizations, grain boundary grooving is the principal failure mechanism.Previous studies have shown that grain boundary grooving in gold films can be prevented by an indium underlay between the substrate and gold. The beneficial effect of the In/Au composite film is mainly due to roughening of the surface of the gold films, redistribution of indium on the gold films and formation of In2O3 on the free surface and along the grain boundaries of the gold films during air annealing.


Sign in / Sign up

Export Citation Format

Share Document