Residual Stress Measurements in Welded and Plastically Deformed Target Structural Materials

2009 ◽  
pp. 133-133-13
Author(s):  
Ajit K. Roy ◽  
Anand Venkatesh ◽  
Satish Dronavalli ◽  
Vikram Marthandam ◽  
Douglas Wells ◽  
...  
Keyword(s):  
Residual Stress ◽  
Structural Materials ◽  
Stress Measurements

Residual Stress Measurements in Welded and Plastically Deformed Target Structural Materials

2005 ◽  
Vol 2 (6) ◽  
pp. 12564 ◽  
Author(s):  
AK Roy ◽  
A Venkatesh ◽  
S Dronavalli ◽  
V Marthandam ◽  
D Wells ◽  
...  
Keyword(s):  
Residual Stress ◽  
Structural Materials ◽  
Stress Measurements

Residual stress measurements and modeling of built-up Box-T sections

2021 ◽  
Vol 160 ◽  
pp. 107336
Author(s):  
Ziqian Zhang ◽  
Gang Shi ◽  
Xuesen Chen ◽  
Lijun Wang ◽  
Le Zhou
Keyword(s):  
Residual Stress ◽  
Stress Measurements

Advances in Hole-Drilling Residual Stress Measurements

2009 ◽  
Vol 50 (2) ◽  
pp. 159-168 ◽  
Author(s):  
G. S. Schajer
Keyword(s):  
Residual Stress ◽  
Hole Drilling ◽  
Stress Measurements

Service Loading Analysis of Wind Turbine Gearbox Rolling Bearings Based on X-Ray Diffraction Residual Stress Measurements

2013 ◽  
Vol 768-769 ◽  
pp. 723-732 ◽  
Author(s):  
Jürgen Gegner ◽  
Wolfgang Nierlich
Keyword(s):  
Residual Stress ◽  
Wind Turbine ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
X Ray Diffraction ◽  
Rolling Bearings ◽  
Wind Turbine Gearbox ◽  
X Ray ◽  
Stress Measurements

Rolling bearings in wind turbine gearboxes occasionally fail prematurely by so-called white etching cracks. The appearance of the damage indicates brittle spontaneous tensile stress induced surface cracking followed by corrosion fatigue driven crack growth. An X-ray diffraction based residual stress analysis reveals vibrations in service as the root cause. The occurrence of high local friction coefficients in the rolling contact is described by a tribological model. Depth profiles of the equivalent shear and normal stresses are compared with residual stress patterns and a relevant fracture strength, respectively. White etching crack failures are reproduced on a rolling contact fatigue test rig under increased mixed friction. Causative vibration loading is evident from residual stress measurements. Cold working compressive residual stresses are an effective countermeasure.

In Situ Thin Film Stress Measurements – A Path to Understanding the Structure and Morphology of Electron Beam Evaporated ZnS

2002 ◽  
Vol 749 ◽  
Author(s):  
Vincent Barrioz ◽  
Stuart J. C. Irvine ◽  
D. Paul
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Electron Beam ◽  
Stress Reduction ◽  
Float Glass ◽  
Film Stress ◽  
Intrinsic Stress ◽  
Ex Situ ◽  
Stress Measurements

ABSTRACTZnS is a material of choice in the optical coating industry for its optical properties and broad transparency range. One of the drawbacks of ZnS is that it develops high compressive intrinsic stress resulting in large residual stress in the deposited layer. This paper concentrates on the evolution of residual stress reduction in ZnS single layers, depending upon their deposition rate or the substrate temperature during deposition (i.e. 22 °C and 133 °C). The substrate preparation is addressed for consideration of layer adhesion. Residual stress of up to − 550 MPa has been observed in amorphous/poor polycrystalline ZnS layers, deposited on CMX and Float glass type substrates, by electron beam evaporation at 22 °C, with a surface roughness between 0.4 and 0.8 nm. At 133 °C, the layer had a surface roughness of 1 nm, the residual stress in the layer decreased to − 150 MPa, developing a wurtzite structure with a (002) preferred orientation. In situ stress measurements, using a novel optical approach with a laser-fibre system, were carried out to identify the various sources of stress. A description of this novel in situ stress monitor and its advantages are outlined. The residual stress values were supported by two ex situ stress techniques. The surface morphology analysis of the ZnS layers was carried out using an atomic force microscope (AFM), and showed that stress reduced layers actually gave rougher surfaces.

Residual Stress Measurements in a 316l Uniaxial Fatigue Sample Manufactured by Laser Powder Bed Fusion

2021 ◽  
Author(s):  
Catrin Mair Davies ◽  
Paul Sandmann ◽  
Tobias Ronneberg ◽  
Paul A Hooper ◽  
Saurabh Kabra
Keyword(s):  
Residual Stress ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Stress Measurements
Sign in / Sign up

Export Citation Format

Share Document