Problems, assumptions and solutions in locomotive design, traction and operational studies

Locomotive design is a highly complex task that requires the use of systems engineering that depends upon knowledge from a range of disciplines and is strongly oriented on how to design and manage complex systems that operate under a wide range of different train operational conditions on various types of tracks. Considering that field investigation programs for locomotive operational scenarios involve high costs and cause disruption of train operations on real railway networks and given recent developments in the rollingstock compliance standards in Australia and overseas that allow the assessment of some aspects of rail vehicle behaviour through computer simulations, a great number of multidisciplinary research studies have been performed and these can contribute to further improvement of a locomotive design technique by increasing the amount of computer-based studies. This paper was focused on the presentation of the all-important key components required for locomotive studies, starting from developing a realistic locomotive design model, its validation and further applications for train studies. The integration of all engineering disciplines is achieved by means of advanced simulation approaches that can incorporate existing AC and DC locomotive designs, hybrid locomotive designs, full locomotive traction system models, rail friction processes, the application of simplified and exact wheel-rail contact theories, wheel-rail wear and rolling contact fatigue, train dynamic behaviour and in-train forces, comprehensive track infrastructure details, and the use of co-simulation and parallel computing. The co-simulation and parallel computing approaches that have been implemented on Central Queensland University’s High-Performance Computing cluster for locomotive studies will be presented. The confidence in these approaches is based on specific validation procedures that include a locomotive model acceptance procedure and field test data. The problems and limitations presented in locomotive traction studies in the way they are conducted at the present time are summarised and discussed.

Influence on Tribological Behavior of PEEK Composite Film Layer on PEEK-PTFE Bearings with Artificial Defect in Dry Condition

In order to explore influence on tribological behavior of PEEK composite film layer in PEEK-PTFE composite radial alumina ball bearings, rolling contact fatigue tests were performed by using the PEEK bearing’s inner rings with the artificial defects in dry condition. When rotation speed and applied load were 600 rpm and 98 N, the number of cycles of the PEEK-PTFE bearings reached 1.0×107 fatigue cycles. The artificial defects with 0.02 mm depth on the raceway surface of the PEEK inner ring was covered with PEEK composite film accumulation.

Abrasive Wear, Scuffing and Rolling Contact Fatigue of DLC-Coated 18CrNiMo7-6 Steel Lubricated by a Pure and Contaminated Gear Oil

Due to extreme working conditions of mining conveyors, which contaminate gear oil with solid particles, their transmissions are exposed to intensive abrasion, scuffing, and even rolling contact fatigue (pitting). These effects shorten gear life. To prevent their occurrence, a wear-resistant coating can be deposited on gear teeth. The resistance to abrasive wear, scuffing, and pitting was investigated and reported in the article. Simple, model specimens were used. Abrasive wear and scuffing were tested using a pin-and-vee-block tribosystem in sliding contact. A cone–three-ball rolling tribosystem was employed to test pitting. The material of the test specimens (pins, vee blocks, cones) was 18CrNiMo7-6 case-hardened steel. Two types of DLC (Diamond-like Coatings) coatings were tested, W-DLC and W-DLC/CrN. The vee blocks and cones were coated. Two industrial gear oils were selected to lubricate the specimens: one with a mineral and one with a synthetic PAO (polyalphaolephine) base, as pure oil or contaminated with solid particles from a coal mine. The results show that, to minimize the tendency to abrasion, scuffing, and pitting of specimens made of 18CrNiMo7-6 steel, the W-DLC/CrN coating should be deposited. This coating also gives very good protection when the lubricating oil is contaminated.

Life and Flaking Failure of 13Cr-2Ni-2Mo and SUS440C Stainless Steel Bearings in Water

The rolling contact fatigue (RCF) tests of 13Cr-2Ni-2Mo and SUS440C stainless steels were carried out in water. Their groove surfaces and the flaking failures were observed. Some hair cracks, wear and high roughness area were found. While the flaking depth of SUS440C was shallower than that of 13Cr-2Ni-2Mo stainless steel, the RCF life of the latter was longer than the former one. The flaking depth did not influence the RCF life.

Gearless Track-Friendly Metro with Guided Independently Rotating Wheels

Track–vehicle severe interaction on track with small curve radius results in rail wear and corrugation, and wheel polygonization, which drain considerable resources for rail grinding and wheels re-profiling in metro lines. To reduce the damage caused by track-vehicle severe interaction, the paper analyzes the reasons leading to rail wear and then proposes an architecture of a metro vehicle with independently rotating wheels driven directly by permanent magnet synchronous motors. The architecture is axle guidance, offered by passive linkages, which ensures that all axles are oriented radially, while control strategy was kept as simple as possible, identifying only two basic traction conditions. The concept is first discussed and then validated through a comprehensive set of running dynamics simulation performed with a multibody software to evaluate rail wear and rolling contact fatigue in traction/braking, coasting with different cant deficiency/excess conditions. The multibody dynamics simulation shows that the proposed architecture is virtually capable of avoiding both wear and rolling contact fatigue damages, and achieves the highest possible track friendliness. The concept of the proposed architecture is a track-fiendly metro architecture and could be a good reference for reducing rail-track interaction damages and maintainace cost.

In situ evaluation of contact stiffness in a slip interface with different roughness conditions using ultrasound reflectometry

Understanding the dynamic condition of the interface between a railway wheel and rail is important to reduce the risks and consider the effectiveness of countermeasures for tribological problems. Traditionally the difficulty in obtaining accurate non-destructive interfacial measurements has hindered systematic experimental investigations. Recently, an ultrasound reflectometry technique has been developed as a direct observation method of a rolling–sliding interface; however, the topography dependence under the high contact pressures in a wheel–rail contact has not been clarified. For this reason, a novel in situ measurement of the contact stiffness using ultrasound reflectometry was carried out for three different levels of roughness. A contact pressure equivalent to that in a wheel–rail interface was achieved by using a high-pressure torsion test approach. The dynamic change of contact stiffness with slip was measured using ultrasound and the influence of roughness was investigated. The measured changes were validated using a newly developed numerical simulation, and mechanisms to explain the observed behaviour were proposed in terms of fracture and plastic deformation of the asperity bonds. These findings could help in understanding the traction characteristics for different roughness conditions and also assist in understanding damage mechanisms better, such as wear and rolling contact fatigue.