scholarly journals A Computational Study on Fluid Flow and Heat Transfer Through a Rotating Curved Duct with Rectangular Cross Section

2021 ◽  
Vol 39 (4) ◽  
pp. 1213-1224
Author(s):  
Rabindra Nath Mondal ◽  
Mohammad Sanjeed Hasan ◽  
Mohammad S. Islam ◽  
Md. Zohurul Islam ◽  
Suvash C. Saha

The understanding of fluid flow and heat transfer (HT) through a rotating curved duct (RCD) is important for different engineering applications. The available literature improved the understanding of the fluid flow and HT through a large-curvature rotating duct. However, the comprehensive knowledge of fluid flow and HT through an RCD with small curvature is little known. This numerical study aims to perform fluid flow characterization and HT through an RCD with curvature ratio 0.001. The spectral based numerical approach investigates the effects of rotation on fluid flow and HT for the Taylor number −1000≤Tr≤1500. A constant pressure gradient force, the Dean number Dn = 100, and a constant buoyancy force parameter, the Grashof number Gr = 500 are used for the numerical simulation. Fortran code is developed for the numerical computations and Tecplot software is used for the post-processing purpose. The numerical study investigates steady solutions and a structure of two-branches of steady solutions is obtained for positive rotation. The transient solution reports the transitional flow patterns and HT through the rotating duct, and two- to four-vortex solutions are observed. In case of negative rotation, time-dependent solutions show that the Coriolis force exhibits an opposite effect to that of the curvature so that the flow characteristics exhibit various flow instabilities. The numerical result shows that convective HT is increased with the increase of rotation and highly complex secondary flow patterns influence the overall HT from the heated wall to the fluid. To validate the numerical results, a comparison with the experimental data is provided, which shows that a good agreement is attained between the numerical and experimental investigations.

2015 ◽  
Vol 9 (3) ◽  
pp. 242 ◽  
Author(s):  
Efstathios Kaloudis ◽  
Dimitris Siachos ◽  
Konstantinos Stefanos Nikas

2013 ◽  
Vol 561 ◽  
pp. 460-465
Author(s):  
Dong Hui Zhang ◽  
Jiao Gao

The objective of this paper is to study the characteristic of a circular tube with a built-in arc belt on fluid flow and heat transfer in uniform wall temperature flows. Numerical simulations for hydrodynamically laminar flow was direct ran at Re between 600 and 1800. Preliminary results on velocity and temperature statistics for uniform wall temperature show that, arc belt can swirl the pipe fluid, so that the fluid at the center of the tube and the fluid of the boundary layer of the wall can mix fully, and plays the role of enhanced heat transfer, but also significantly increases the resistance of the fluid and makes the resistance coefficient of the enhanced tube greater than smooth tube. The combination property PEC is all above 1.5.


Author(s):  
CJ Ho ◽  
GN Sou ◽  
CM Lai

This paper presents a numerical study of transient buoyancy-induced fluid flow and heat transfer between two horizontal, differentially heated pipelines inside a circular, air-filled enclosure. Numerical simulations based on the finite difference method were conducted to investigate the flow mode transition of the buoyant airflow and its effects on the heat transfer characteristics of the pipelines. The results indicate that the fluid flow complexity and the heat transfer of air between the pipelines are strongly affected by the Rayleigh number. When Ra = 6 × 105 and 1.2 × 106, both the flow field and the temperature distribution exhibit periodic variations with different patterns. The former ( Ra = 6 × 105) is a complete alteration of the flow direction from clockwise to counterclockwise, whereas the latter is a variation in the flow field strength that varies between strong and weak. The latter has a lower variation frequency than that of the former.


Sign in / Sign up

Export Citation Format

Share Document