ULTRASONIC TESTING OF SPESIMENS AT THE DEVELOPMENT AND TESTING PROCESS OF NEW CFRP GRADES

2021 ◽  
pp. 86-95
Author(s):  
A.S. Boychuk ◽  
◽  
I.A. Dikov ◽  
A.S. Generalov ◽  
V.Yu. Chertishchev ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Nondestructive Testing ◽  
Ultrasonic Testing ◽  
Ultrasonic Pulse ◽  
Curved Beam ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Pulse Echo

Nondestructive testing results of carbon fiber reinforced plastics (CFRP) specimens at the development and testing process are given at that paper. Ultrasonic pulse-echo technique is the most applicable for CFRP monolithic panels and curved beam specimens testing. It is shown that ultrasonic testing allows optimizing the mode in the process of developing molding modes for new CFRP grades. At the test stages it allows to exclude defective specimens from the testing process and estimate the sorts and damage sizes after the tests.

Mid-infrared pulsed laser ultrasonic testing for carbon fiber reinforced plastics

Ultrasonics ◽  
2018 ◽  
Vol 84 ◽  
pp. 310-318 ◽  
Author(s):  
Masahiro Kusano ◽  
Hideki Hatano ◽  
Makoto Watanabe ◽  
Shunji Takekawa ◽  
Hisashi Yamawaki ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Ultrasonic Testing ◽  
Pulsed Laser ◽  
Fiber Reinforced ◽  
Laser Ultrasonic ◽  
Mid Infrared ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

INCREASING SENSITIVITY OF EDDY CURRENT NON-DESTRUCTIVE TESTING OF DELAMINATION IN CARBON-FIBER REINFORCED PLASTICS

2021 ◽  
pp. 28-37
Author(s):  
P. N. Shkatov ◽  
G. A. Didin ◽  
A. A. Ermolaev
Keyword(s):  
Carbon Fiber ◽  
Eddy Current ◽  
Calculation Model ◽  
Fiber Reinforced ◽  
Destructive Testing ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced ◽  
The Difference

The paper is concerned with increasing sensitivity of eddy current nondestructive testing of most dangerous delamination in carbon-fiber reinforced plastics (CFRP). Increased sensitivity is achieved by separate registration and comparison of eddy current signals obtained from a set of stratifications of carbon fibers with the same orientation. The separation of eddy current signals is possible due to pronounced anisotropy of the electrical conductivity of the layers dominant in the direction of the fibers of the corresponding layer. Eddy-current signals are registered by eddy current probes with maximum sensitivity in a given angular direction. Prior to the scan eddy current signals of the probe are leveled on a defect-free area. The influence of the working gap on the difference between the eddy current signals of the probe is suppressed by normalizing it according to one of the signals. The analysis of the registered signals from delamination has been performed using an approximate calculation model. The reliability of the obtained results has been confirmed by comparison with experimental results and calculations using the finite element method.

Sign in / Sign up

Export Citation Format

Share Document