surface quality
Recently Published Documents


TOTAL DOCUMENTS

3139
(FIVE YEARS 916)

H-INDEX

49
(FIVE YEARS 12)

2022 ◽  
Author(s):  
Weining Li ◽  
Khamis Essa ◽  
Sheng Li

Abstract For heat-assisted single point incremental sheet forming (SPIF) works of Ti-6Al-4V sheets, the use of lubricant has shown significant effects on surface quality and geometric accuracy at higher temperatures. Molybdenum disulphide (MoS2) is a common lubricant widely used in SPIF works, however, it usually indicates ineffective performance at high temperatures. This article has studied different lubricants of MoS2 lubricants and proposed a novel mixture of MoS2 to provide better surface quality and improve geometric accuracy. A forming tool with a ball-roller and water channel was designed to enable the MoS2 mixture to pass through the tool tip, allowing easy application of the lubricant on the localised area and reduce the thermal expansion on the ball-roller. Surface roughness analysis has revealed that the water-cooling MoS2 mixture performed well in reducing friction effects and achieved better geometric accuracy. Forming forces measurements, scanning electron microscope (SEM), energy dispersive X-ray Analysis (EDX) and micro-hardness tests also indicated that a higher strain hardening behaviour was detected for the water-cooling MoS2 mixture.


Author(s):  
Po Jin ◽  
Qi Gao ◽  
Quanzhao Wang ◽  
GuangYan Guo

In this paper, the finite element cutting simulation model with irregular distribution of multiple particles is established, the stress and strain distribution of SiC particles in the process of machining, as well as the material removal mechanism are analyzed. The effects of cutting velocity and feed per tooth on the surface quality of the material are also analyzed. The effect of feed per tooth on subsurface damage is revealed. The results show that in the micro-milling of SiCp/Al2024 composites, the particle removal form is mainly crushing and extraction. The surface defects of the workpiece mainly include pits, scratches, cracks, and extrusion damage. When the cutting velocity increases, the surface defects gradually change to crack, which can improve the surface quality of the workpiece. Increasing the feed per tooth will increase the surface defects of the workpiece and lead to poor surface quality. When the feed per tooth increased from 0.428 µm to 0.714 µm, the subsurface damage thickness increased from 35.2 µm to 47.3 µm.


Machines ◽  
2022 ◽  
Vol 10 (1) ◽  
pp. 49
Author(s):  
Damian Dzienniak

This paper describes a surface-roughness study performed on samples manufactured additively using the Multi Jet Fusion (MJF) technology. The samples were divided into three groups based on the material used in the process: polypropylene (PP), thermoplastic polyurethane (TPU), and polyamide 11 (PA11). Subsequently, they were tested by means of a roughness-measuring system, which made it possible to determine the typical surface roughness parameters (Ra, Rq, Rz). The tests were designed to examine whether the placement and orientation of 3D objects while printing, in connection with the material used, can significantly influence the surface quality of MJF-printed objects. The results show that the TPU samples have a surface roughness much higher than the PP and PA11 ones, which exhibit roughness levels very similar to each other. It can also be concluded that surfaces printed vertically (along the Z-axis) tend to be less smooth—similarly to the surfaces of objects made of TPU located in the central zones of the print chamber during printing. This information may be of value in cases where low surface roughness is preferred (e.g., manufacturing patient-specific orthoses), although this particular study does not focus on one specific application.


2022 ◽  
Author(s):  
Shuaipu Wang ◽  
Jie Liang

Abstract In order to reduce the delamination damage of carbon fiber reinforced polymer (CFRP) drilling and improve the drilling quality. A variable feed drilling method based on sinusoidal curve was proposed, that is, when the drill at a distance of 1mm from the hole exit, the feed rate of the drill would be reduced according to the rule of sinusoidal curve. The method is compared with the traditional feed drilling by experiment, and the influence of the variable feed drilling on thrust force, delamination factor, surface quality, surface roughness of hole wall and exit hole wall morphology are analyzed. The results show that compared with constant-feed drilling, the variable-feed drilling based on sinusoidal curve reduces the thrust force near the hole exit, and greatly improves the delamination factor, surface quality and hole wall morphology at the exit. But the influence on the hole wall roughness is not particularly obvious.


2022 ◽  
Author(s):  
Peng Wang ◽  
Qingshun Bai ◽  
Kai Cheng ◽  
Liang Zhao ◽  
Hui Ding

Abstract The surface integrity and machining accuracy of thin-walled micro parts are significantly affected by micro-milling parameters mostly because of their weak stiffness. Furthermore, there is still a lack of studies focusing on parameters optimization for the fabrication of thin-walled microscale parts. In this paper, an innovative approach is proposed for the optimization of machining parameters with the objectives of surface quality and dimension accuracy, which integrates the Taguchi method, principal component analysis method (PCA) and the Non-dominated sorting genetic algorithm (NSGA-II). In the study, surface arithmetic average height Sa, surface root mean square height Sq, and 3-D fractal dimension Ds are selected to evaluate surface quality. Then micro-milling experiments are conducted based on the Taguchi method. According to the experimental results, the significance of machining parameters can be determined by range analysis. Besides, regression models for the responses are developed comparatively, and the PCA method is employed for dimension reduction of the optimization objective space. Finally, two combinations of machining parameters with the highest satisfaction are obtained through NSGA-II, and verification experiments are carried out. The results show that the surface quality and dimension accuracy of the thin-walled microscale parts can be simultaneously improved by using the proposed approach.


2022 ◽  
Vol 58 (4) ◽  
pp. 114-129
Author(s):  
Yongsun Lee ◽  
Jinrae Cho ◽  
Seongryeol Han

The aim of the paper consisted in the development of an injection mold for plastic horn cover parts in commercial vehicles. Three mold types were designed in anticipation of the structure and quality of molds, and injection molding numerical analyses were conducted for the three types of molds. One mold type was selected in consideration of the resin flow patterns inside the mold, surface quality, and final deflection amount of the horn cover. To perform optimal injection molding using the selected mold, optimization of injection molding parameters was performed using the Taguchi method, one of the designs of experiment (DOE) and ANOVA methods. As a result, it was confirmed that the deflection amount of the molding under optimal molding parameters decreased by about 34.3% compared to the deflection amount before optimization of the molding parameters. Based on these encouraging results, the previously selected mold type was actually manufactured. The horn cover was molded using the obtained optimal injection molding parameters to the manufactured mold. To verify the precision of the molded horn cover, the deflection amount of the molding was measured with a 3D scanner. The deflection amount of the horn cover was estimated to be about 11% to 43% larger for each measurement position than the deflection amounts in the analysis results. The manufactured mold was revised to solve the problem that the deflection amount of the actual molding is larger than the deflection amount predicted by injection molding analysis. The dimensions and surface quality of the horn cover with a revised mold were satisfactory.


Sign in / Sign up

Export Citation Format

Share Document