scholarly journals Potential Coir Fibre Composite for Small Wind Turbine Blade Application

2016 ◽  
Vol 2 (1) ◽  
pp. 42-44 ◽  
Author(s):  
B Bakri ◽  
◽  
S Chandrabakty ◽  
R Alfriansyah, ◽  
A Dahyar
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Fibre Composite ◽  
Wind Turbine Blade ◽  
Small Wind Turbine ◽  
Coir Fibre

scholarly journals Examination of simplified load model on fatigue analysis of small wind turbine blade using aeroelastic analysis

2015 ◽  
Vol 81 (823) ◽  
pp. 14-00050-14-00050
Author(s):  
Mitsumasa IINO ◽  
Hideki TOKUYAMA ◽  
Hiroshi SEGAWA ◽  
Makoto IIDA
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Fatigue Analysis ◽  
Wind Turbine Blade ◽  
Load Model ◽  
Small Wind Turbine ◽  
Aeroelastic Analysis

Smart structure for small wind turbine blade

2013 ◽  
Author(s):  
E. E. Supeni ◽  
J. A. Epaarachchi ◽  
M. M. Islam ◽  
K. T. Lau
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Wind Turbine Blade ◽  
Smart Structure ◽  
Small Wind Turbine

scholarly journals An investigation into a small wind turbine blade design

2021 ◽  
Author(s):  
Sayem Zafar
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Structural Integrity ◽  
Electrical Power ◽  
Single Layer ◽  
Wind Turbine Blade ◽  
Blade Design ◽  
Small Wind Turbine ◽  
Start Up ◽  
Turbine Blade Design

The objective of the project was to design a small wind turbine blade which is aerodynamically efficient and easy to manufacture. Preliminary aerodynamic analysis concluded NACA 63-425 to be the most efficient airfoil. Blade geometry was determined after calculating baseline geometric values for low drag which was then used to calculate power. Blade's structural integrity was studied using ANSYS® software. Tested results yielded that a single layer of E-fibreglass-epoxy is good enough to sustain the prescribed loads. The results were used to calculate the total weight of the blade which was then used to determine the start-up speed. Overall the project was successful in designing a wind turbine blade that produced 450 [W] of electrical power at 4[m/s] wind speed with the start-up speed of around 2[m/d]. The project fulfilled its objective which was to design a more effective wind turbine blade with manufacturability in mind.

scholarly journals Design and Analysis of Dimple Arrangement on a Small Wind Turbine Blade

2019 ◽  
Vol 9 (2) ◽  
pp. 3552-3557
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Aerodynamic Performance ◽  
Wind Turbine Blade ◽  
Performance Estimation ◽  
Cfd Analysis ◽  
Blade Surface ◽  
Ansys Fluent ◽  
Small Wind Turbine ◽  
Overall Performance

This article predominantly focuses on the performance estimation of a small wind turbine blade when a dimple arrangement is made along its upper surface. The dimple arrangement is grooved at two locations: 0.25c and 0.5c, where c is the chord length of the turbine blade. A CFD analysis using the k-ε turbulence model is carried out on the selected blade sections NREL S823 and S822. The continuity and momentum equations are solved using ANSYS Fluent Solver to assess the aerodynamic performance of the proposed design. The effect of introducing a dimple on the blade surface has shown to delay the flow separation, with the formation of vortices. Further, the overall performance of the blade is simulated using GH BLADED and the results acquired are discussed.

scholarly journals Vibration Analysis of a Small Wind Turbine Blade

2016 ◽  
Vol 8 (5) ◽  
pp. 2121-2126 ◽  
Author(s):  
Ganesh B. Taware ◽  
Sham H. Mankar ◽  
Ghagare V. B. ◽  
Bharambe G. P. ◽  
Sandip A. Kale
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Vibration Analysis ◽  
Wind Turbine Blade ◽  
Small Wind Turbine

scholarly journals An investigation into a small wind turbine blade design

2021 ◽  
Author(s):  
Sayem Zafar
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Structural Integrity ◽  
Electrical Power ◽  
Single Layer ◽  
Wind Turbine Blade ◽  
Blade Design ◽  
Small Wind Turbine ◽  
Start Up ◽  
Turbine Blade Design

The objective of the project was to design a small wind turbine blade which is aerodynamically efficient and easy to manufacture. Preliminary aerodynamic analysis concluded NACA 63-425 to be the most efficient airfoil. Blade geometry was determined after calculating baseline geometric values for low drag which was then used to calculate power. Blade's structural integrity was studied using ANSYS® software. Tested results yielded that a single layer of E-fibreglass-epoxy is good enough to sustain the prescribed loads. The results were used to calculate the total weight of the blade which was then used to determine the start-up speed. Overall the project was successful in designing a wind turbine blade that produced 450 [W] of electrical power at 4[m/s] wind speed with the start-up speed of around 2[m/d]. The project fulfilled its objective which was to design a more effective wind turbine blade with manufacturability in mind.

Sign in / Sign up

Export Citation Format

Share Document