Research of Spherical Capsule Feeding System in Hydraulic Pipelines

Feeding the material to be transported in the hydraulic pipelines to the system is a subject open to research. The shape, size and density of the material gain importance in the selection of feeding systems. Finding the pressure drops that occur in the flow of spherical ice capsules with water is the basis of the research. However, before the measurements were made, preliminary research was carried out on feeding the capsules to the system during the installation of the experimental set-up. In the experimental study with solid particles with the diameter ratios (0.8) and densities (960 kg/m3) with smaller dimensions (d=0.014m), a pipe construction was obtained in which the solid particles are easily fed into the hydraulic pipeline. Experimental study revealed that lower than predicted pressures occur at the point where solid particles are fed into the pipe. This result means a greater pressure drop than the pressure drops obtained in the venturimeter zone with the same diameter ratio. In this article includes a step-by-step method and a sample pipe geometry for studies that require a low pressure zone in hydraulic pipelines. The pipe geometry designed in this study will form a model for the supply systems in the pipelines. The low pressure region is provided with a pipe and flow arrangement without consuming energy.

Evaluation of seismic capacity and response according to the nonlinear modeling approach of members in steel moment frames

In this paper, the aim is to evaluate the seismic behavior of steel momment frames by nonlinear static analysis and incremental dynamic analysis. In this regard, 5 and 10 story frames in both intermediate and special ductility have been used. Since the type of sections and elements used in modeling are among the parameters that affect the behavior of the structure, in this study, which was performed using Opensees software, fiber sections were used for two types of beam elements. Non-linear column (distributed plasticity) and articulated beam element (concentrated plasticity) are used. The results of the analysis show that the ratio of the collapse capacity of the frames to each other varies between 1% to 6%. On the other hand, by deepening the research on one of the frames, it was shown that the stiffness ratio between the end springs and the middle member will affect the difference between the collapse capacity shown in the analysis.

Design, Construction and Experimental Study of a Solar Still for Brackish Water Purification under Djiboutian Climate

A single sloped solar still were designed and fabricated to operate under Djibouti city weather condition during the period April-May 2019. In this study, a single slope solar still has been constructed from materials available on the local market. Series of experiments were carried out on solar still using brackish water. Ambient temperature, water temperature in basin, absorber plate temperature, glass cover temperature and vapor temperature were measured along with the hourly water production. This study has revelead that the vapor temperature is always above that the others temperatures for all the four days of experiments. Then, the effect of water amount in the basin on productivity of solar still was investigated using different amount of water 6 L, 8 L, 10 L and 12 L. The experimental results show that the total accumulated distillate output for the single slope solar still is 2490 mL, 2390 mL, 2240 mL and 2015 mL, respectively. However, it is observed that with increase in basin water amount distillate water production decreases. On the other hand, the effect of wind speed on the daily productivity of solar still is evaluated. Experimental investigations show that the cumulative productivity increases when the wind speed average increase. Finally, water quality analyses were conducted before and after the experiments. The average analysis results obtained showed a removal efficiency of 98.16%, 98.42%, 97.43% and 95.39% for TDS, electrical conductivity, hardness water and chloride, respectively. It was also observed that data obtained of the product water were within the normal range prescribed by World Health Organization (WHO) standards.

Study on Effect of Productivity on Applying Ergonomic Principle

This study was to investigate the effect of productivity in the construction industry due to the un-ergonomic working atmosphere. The construction industry is a large number of workers concerning industry it leads to productivity loss or due risk factors in the working site. In the review, to improve analysis a drawback, we took ergonomic awareness questionnaire survey among the Engineers in Karur district. Based on the survey results, the awareness of term ergonomics is only 20% and Engineers accept to adopt the ergonomics principles. We extended our work to apply ergonomic principles in the site. The ergonomic deficiency was identified, and gradually new ergonomic principles were applied in plastering and brickwork. 1% increase in productivity measured at 7 days of implementation.