scholarly journals Effect of Inflation Pressure on Tire Rolling Resistance and Vehicle Fuel Economy

2017 ◽  
Vol 90 (3) ◽  
pp. 77-79 ◽  
Author(s):  
Walter H. Waddell
2013 ◽  
Vol 16 (1) ◽  
pp. 18-21 ◽  
Author(s):  
Mário Szabó ◽  
Radoslav Majdan ◽  
Zdenko Tkáč ◽  
Rastislav Čápora ◽  
Ľubomír Hujo

Abstract This paper deals with the importance of fuel economy in road freight transport. It provides the calculation of financial savings for fuel savings of 0.5 l per 100 km. In the subsequent part, some factors that influence the fuel consumption are specified, e.g. aerodynamic resistance, rolling resistance, and tyre inflation pressure. The effect of tyre inflation pressure on fuel economy has been tested on four selected towing vehicles. Based on the results obtained, it can be stated that tyre pressure has a great impact on fuel consumption. A one-bar pressure reduction of tyres can increase the fuel consumption by 0.5 l per 100 km.


2018 ◽  
Vol 46 (2) ◽  
pp. 93-104 ◽  
Author(s):  
L. J. Bachman

ABSTRACT Data from air cavity thermistors, tire pressure–monitoring systems (TPMS), and SAE J1269 rolling resistance tests were analyzed to evaluate the significance of changes in tire pressure on rolling resistance during fuel economy tests of class 8 tractor trailers. Thermistor data show that air cavity temperatures vary, with the main increase happening during the warm-up run and measurable cooling during the fuel measurement breaks between runs. Inflation pressure also increases by 50–70 kPa during the warm-up run, but once the tire has warmed up, the pressure is more stable, rarely varying by more than 20 kPa during a test run. Results of SAE J1269 rolling resistance tests allow estimation of rolling resistance force for any specified load and inflation pressure. Using the test weight of the truck, the rolling resistance force was estimated for inflation pressures ranging from 550 to 860 kPa. The relationship between the inflation pressure and rolling resistance was roughly linear. The relationship was then used to estimate changes in fuel consumption due to changes in inflation pressure normalized to the cold inflation pressure. For each change of relative inflation pressure of 5%, rolling resistance would change by about 1%. Using a common return factor of a 1% change in fuel consumption for every 5% change in rolling resistance, a change in relative inflation pressure of 5% would result in a change of fuel consumption of about 0.2%. The precision of the J1321 fuel economy tests was measured to be plus or minus about 1%. This suggests that the warm-up run provided for the test method stabilizes the tire pressure and rolling resistance and that interference due to changes in rolling resistance during a test run or between runs is a concern only for tests that measure small changes in fuel consumption. While the results obtained here are used to assess the effect of inflation pressure on the SAE J1321 test and apply only to the particular tires tested, the method of analysis may be useful in the assessment of the effect of over- or underinflated tires on fuel consumption in the wider long-haul trucking fleet.


2015 ◽  
Vol 43 (2) ◽  
pp. 144-162
Author(s):  
Al Cohn

ABSTRACT Maintaining proper tire inflation is the number one issue facing commercial fleets today. Common, slow-leaking tread area punctures along with leaking valve stems and osmosis through the tire casing lead to tire underinflation with a subsequent loss in fuel economy, reduction in retreadability, tread wear loss, irregular wear, and increase in tire-related roadside service calls. Commercial truck tires are the highest maintenance cost for fleets second only to fuel. This article will examine tire footprint analysis, rolling resistance data, and the effect on vehicle fuel economy from tires run at a variety of underinflated, overinflated, and recommended tire pressures. This analysis will also include the tire footprint impact by running tires on both fully loaded and unloaded trailers. The footprint analysis addresses both standard dual tires (295/75R22.5) along with the newer increasingly popular wide-base tire size 445/50R22.5.


2014 ◽  
Vol 1070-1072 ◽  
pp. 392-397
Author(s):  
Jun Hui Xu ◽  
Ming Qiu Gao ◽  
Ji Qiang Gao ◽  
Xiang Bao

In the background of the main technologies of fuel economy in automobiles developed to a certain stage, it is necessary to reduce fuel consumption and increase the engine efficiency by developing other auxiliary technologies such as improving the ratio of pure energy drive, low rolling resistance tires, tire pressure monitoring system and gear shift indicators (GSI). This article introduces the principle of GSI, analyses how GSI works in improving engine efficiency, and then evaluates the method for determination of the relative saving rate of fuel consumption, which method was introduced in the EU regulation EC No. 65/2012.


2017 ◽  
Author(s):  
Arthur Braga Thiriet ◽  
Fabrício José P. Pujatti ◽  
Paulo César S. Araújo

2016 ◽  
Vol 17 (2) ◽  
pp. 237-244 ◽  
Author(s):  
J. Ejsmont ◽  
S. Taryma ◽  
G. Ronowski ◽  
B. Swieczko-Zurek

2015 ◽  
Vol 13 (2) ◽  
pp. e0211 ◽  
Author(s):  
Parviz Tomaraee ◽  
Aref Mardani ◽  
Arash Mohebbi ◽  
Hamid Taghavifar

<p>Qualitative and quantitative analysis of contact patch length-rolling resistance, contact patch width-rolling resistance and tire deflection-rolling resistance at different wheel load and inflation pressure levels is presented. The experiments were planned in a randomized block design and were conducted in the controlled conditions provided by a soil bin environment utilizing a well-equipped single wheel-tester of Urmia University, Iran. The image processing technique was used for determination of the contact patch length and contact patch width. Analysis of covariance was used to evaluate the correlations. The highest values of contact length and width and tire deflection occurred at the highest wheel load and lowest tire inflation pressure. Contact patch width is a polynomial (order 2) function of wheel load while there is a linear relationship between tire contact length and wheel load as well as between tire deflection and wheel load. Correlations were developed for the evaluation of contact patch length-rolling resistance, contact patch width-rolling resistance and tire deflection-rolling resistance. It is concluded that the variables studied have a significant effect on rolling resistance.</p>


Sign in / Sign up

Export Citation Format

Share Document