Strain Detection System for High-rise Building Pile Foundation Based on Distributed Optical Fiber Sensor

Author(s):  
Danjiang Chen ◽  
Zhenyi Zhang ◽  
Yutian Liu
Sensor Review ◽  
2015 ◽  
Vol 35 (4) ◽  
pp. 382-388 ◽  
Author(s):  
Yage Zhan ◽  
Qiao Yu ◽  
Kun Wang ◽  
Fu Yang ◽  
Borui Zhang

Purpose – The purpose of this paper is to theoretically analyze and experimentally demonstrate the investigation on and optimization of a distributed optical fiber sensor based on phase-sensitive optical time domain reflectometer (F-OTDR) for disturbance detection. Design/methodology/approach – The F-OTDR system is investigated and optimized in two aspects: the hardware parameter and the interrogation scheme. Findings – Based on the optimized hardware and the new interrogation scheme, the performances of the F-OTDR system have been improved greatly, compared with conventional F-OTDR system. A location accuracy of 2 m and a signal-to-noise ratio (SNR) of 16 dB have been achieved under a spatial resolution of 8 m. On the other hand, four disturbances at four different locations have been detected and located simultaneously, which is the most effective detection system with the maximum detection capability reported to date, to the best of the authors’ knowledge. Originality/value – Four disturbances at four different locations have been detected and located simultaneously, which is the most effective detection system with the maximum detection capability reported to date, to the best of the authors’ knowledge. With same hardware conditions, more existing disturbances can be detected by using the new interrogation scheme, which is helpful to reduce the miss report of disturbance.


Symmetry ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1166
Author(s):  
Bin Liu ◽  
Jianping He ◽  
Shihai Zhang ◽  
Yinping Zhang ◽  
Jianan Yu ◽  
...  

Brillouin frequency shift (BFS) of distributed optical fiber sensor is extracted from the Brillouin gain spectrum (BGS), which is often characterized by Lorenz type. However, in the case of complex stress and optical fiber self damage, the BGS will deviate from Lorenz type and be asymmetric, which leads to the extraction error of BFS. In order to enhance the extraction accuracy of BFS, the Lorenz local single peak fitting algorithm was developed to fit the Brillouin gain spectrum curve, which can make the BSG symmetrical with respect to the Brillouin center frequency shift. One temperature test of a fiber-reinforced polymer (FRP) packaged sensor whose BSG curve is asymmetric was conducted to verify the idea. The results show that the local region curve of BSG processed by the developed algorithm has good symmetry, and the temperature measurement accuracy obtained by the developed algorithm is higher than that directly measured by demodulation equipment. Comparison with the reference temperature, the relative measurement error measured by the developed algorithm and BOTDA are within 4% and 8%, respectively.


2010 ◽  
Author(s):  
C. Perrotton ◽  
M. Slaman ◽  
N. Javahiraly ◽  
H. Schreuders ◽  
B. Dam ◽  
...  

2010 ◽  
Vol 37 (6) ◽  
pp. 1501-1504
Author(s):  
高存孝 Gao Cunxiao ◽  
朱少岚 Zhu Shaolan ◽  
冯莉 Feng Li ◽  
宋志远 Song Zhiyuan ◽  
曹宗英 Cao Zongying ◽  
...  

2019 ◽  
Vol 46 (4) ◽  
pp. 0410001 ◽  
Author(s):  
章征林 Zhang Zhenglin ◽  
高磊 Gao Lei ◽  
孙阳阳 Sun Yangyang ◽  
张清华 Zhang Qinghua ◽  
曾鹏 Zeng Peng

Sign in / Sign up

Export Citation Format

Share Document