Numerical Simulation on Failure Patterns of Rock Discs and Rings Subject to Diametral Line Loads

2004 ◽  
Vol 261-263 ◽  
pp. 1517-1522 ◽  
Author(s):  
Wan Cheng Zhu ◽  
K.T. Chau ◽  
Chun An Tang
Keyword(s):  
Tensile Strength ◽  
Standardized Test ◽  
Process Analysis ◽  
Failure Process ◽  
Brazilian Test ◽  
Rock Failure ◽  
Numerical Code ◽  
Failure Patterns ◽  
Rock Failure Process ◽  
Indirect Tensile

Brazilian test is a standardized test for measuring indirect tensile strength of rock and concrete disc (or cylinder). Similar test called indirect tensile test has also been used for other geomaterials. Although splitting of the disc into two halves is the expected failure mode, other rupture modes had also been observed. More importantly, the splitting tensile strength of rock can vary significantly with the specimen geometry and loading condition. In this study, a numerical code called RFPA2D (abbreviated from Rock Failure Process Analysis) is used to simulate the failure process of disc and ring specimens subject to Brazilian test. The failure patterns and splitting tensile strengths of specimens with different size and loading-strip-width are simulated and compared with existing experimental results. In addition, two distinct failure patterns observed in ring tests have been simulated using RFPA2D and thus this verifies the applicability of RFPA2D in simulating rock failure process under static loads.

Three Dimensional Numerical Approach to Splitting Failure of Rock Discs

2007 ◽  
Vol 353-358 ◽  
pp. 921-924
Author(s):  
Tao Xu ◽  
Tian Hui Ma ◽  
Chun An Tang ◽  
Zheng Zhao Liang
Keyword(s):  
Standardized Test ◽  
Process Analysis ◽  
Failure Process ◽  
Numerical Approach ◽  
Rock Failure ◽  
Test Method ◽  
Tensile Failure ◽  
Numerical Code ◽  
Failure Patterns ◽  
Splitting Failure

The Brazilian splitting tests have been commonly and widely used as a standardized test method on disc or cylinder specimens to measure the indirect tensile strength of rocks in mining engineering and other rock engineering. In this paper, a novel numerical code, 3D Rock Failure Process Analysis code, was applied to implement the splitting tensile failure tests on rock discs. The influences of the heterogeneity on stress distribution in rock are also discussed and the splitting failure patterns of specimens subjected to Brazilian tests are simulated. The simulated splitting results of rock discs were found quite realistic, which indicate that the rock failure analysis method is applicable and practical for the study of rock disc splitting failure.

scholarly journals The Fracturing Behavior of Tight Glutenites Subjected to Hydraulic Pressure

Processes ◽  
2018 ◽  
Vol 6 (7) ◽  
pp. 96 ◽  
Author(s):  
Zhichao Li ◽  
Lianchong Li ◽  
Zilin Zhang ◽  
Ming Li ◽  
Liaoyuan Zhang ◽  
...  
Keyword(s):  
Process Analysis ◽  
Failure Process ◽  
Three Dimensional ◽  
Axial Ratio ◽  
Numerical Code ◽  
Hydraulic Fractures ◽  
Hydraulic Pressure ◽  
Gravel Size ◽  
Rock Failure Process ◽  
Common Laboratory

Tight glutenites are typically composed of heterogeneous sandstone and gravel. Due to low or ultra-low permeability, it is difficult to achieve commercial production in tight glutenites without hydraulic fracturing. Efficient exploitation requires an in-depth understanding of the fracturing behavior of these reservoirs. This paper provides a numerical method that integrates the digital image processing (DIP) technique into a numerical code rock failure process analysis (RFPA). This method could consider the glutenite heterogeneities, including intrarock and interrock heterogeneities, and the practicability is verified through two numerical tests. Two-dimensional (2D) simulations show hydraulic fractures (HFs) can penetrate or deflect to propagate along the gravels, depending on the magnitude of stress anisotropy and gravel strength. Three-dimensional (3D) simulations with the consideration of gravel distribution orientation, gravel size and axial ratio show HFs could propagate past the gravel with no deflection, forming a bypass fracture that is not easy to observe in common laboratory experiments. HFs could also deflect to propagate along the gravels. The impacts of the gravel distribution orientation, gravel size and axial ratio are discussed in detail. The main propagation modes of HFs intersecting the gravels are summarized as: (1) penetrating directly; (2) deflecting to propagate along the gravels to form distorted HFs; (3) propagating to bypass the gravels; (4) a combination of (1) and (2), or (2) and (3).

Numerical Study of Elastic-Brittle Failure of Notched Openings in Rocks

2005 ◽  
Vol 297-300 ◽  
pp. 2605-2611
Author(s):  
Shan Yong Wang ◽  
S.K. Au ◽  
K.C. Lam ◽  
Chun An Tang
Keyword(s):  
Numerical Study ◽  
Progressive Failure ◽  
Process Analysis ◽  
Failure Process ◽  
Confining Pressure ◽  
Numerical Code ◽  
Tunnel Wall ◽  
Model Studies ◽  
Borehole Breakout ◽  
Rock Failure Process

Borehole breakout is the process by which portions of borehole or tunnel wall fracture or spall when subjected to compressive stresses. The stress-strain characteristics of rock during loading and unloading confining pressure are studied firstly. To overcome the difficulties in analytical model studies, a numerical code, RFPA2D (Rock Failure Process Analysis), developed by CRISR, Northeastern University, China, is used to investigate the progressive failure of breakout around tunnel. The heterogeneity of rock was also taken into account in the software. The numerical simulation reproduces the formation notch in rocks by the growth, interaction and coalescence of randomly distributed macrocracks. It is illustrated from the numerical simulated results that breakout direction of tunnel is parallel with the minor stress tensor in the plane perpendicular to the borehole axis. Specifically due to the inclusion of heterogeneity, some peculiarities are studied both in the evolution of fracture and the influence of borehole on the peak intensity of specimen as well as the AE event patterns.

Numerical Study of Effect of Joint Tip Distance from Sample End on Rock Failure

2014 ◽  
Vol 501-504 ◽  
pp. 244-247
Author(s):  
Yun Jie Zhang ◽  
Cheng Fan
Keyword(s):  
Uniaxial Compression ◽  
Numerical Study ◽  
Process Analysis ◽  
Rock Fracture ◽  
Failure Process ◽  
Strain Curve ◽  
Peak Stress ◽  
Rock Failure ◽  
Peak Strain ◽  
Failure Patterns

In this paper,the mechanical properties of rock experiencing the variation of joint tip distance from sample end under uniaxial compression condition were simulated.Numerical simulation for the different rock sample in the uniaxial compression have been conducted to evaluate the effects of joint tip distance from sample end on the overall mechanical behaviour of jointed rock masses. It was done using the Rock Failure Process Analysis program RFPA2D. Numerically simulated stress-strain curve, peak stress, peak strain and failure patterns were compared with the corresponding physical tests. We found that specimen joint tip distance from sample end corresponding value (distance from the crack tip to the compression surface) linear relationship with the compressive strength values .Numerical simulations agree well with physical results, it is shown that RFPA2D is suitable for the analysis of joint tip distance from sample end effect on rock fracture.

Sign in / Sign up

Export Citation Format

Share Document