Design Manufacture of Fixture Fire Fighter Kit

Wirda Novarika; Fatahul Arifin; Eka Satria Martomi; Indra Gunawan; Fathur Raihan Perdana

doi:10.53893/ijrvocas.v1i3.58

Design Manufacture of Fixture Fire Fighter Kit

International Journal of Research in Vocational Studies (IJRVOCAS) ◽

10.53893/ijrvocas.v1i3.58 ◽

2021 ◽

Vol 1 (3) ◽

pp. 08-16

Author(s):

Wirda Novarika ◽

Fatahul Arifin ◽

Eka Satria Martomi ◽

Indra Gunawan ◽

Fathur Raihan Perdana

Keyword(s):

Forest Fires ◽

Fire Fighter ◽

Simulation Design

Forest fires are one that needs attention in Indonesia. Due to spent a lot of money to solve this problem. One of the tools to solve this problem is fire fighter, so in case is need to make the fixture can manufacture the fire fighter kit. In this study, we propose the fixture that can be produce the kit. It call fixture fire fighter kit. Autodesk inventor is applied in the simulation design and also it is considering with the ergonomic for the worker especially the Indonesian male. Finally, this tool can be resistant with load 50 kg, the deflection is 0.831 mm, and the maximum von misses stress is 34.12 MPa.

Download Full-text

Water curtain as protection for fire fighter vehicle from exposure forest fires

Forestry Engineering Journal ◽

10.12737/14173 ◽

2015 ◽

Vol 5 (3) ◽

pp. 248-254

Keyword(s):

Forest Fire ◽

Forest Fires ◽

Fire Fighter ◽

Modes Of Operation ◽

Water Curtain ◽

Reduce Risk

In the article considered question protection of forest fire vehicle and is offered design of the equipment to create the water curtain. Are applied two contours for creation of a water veil allowing to make protection of all car from above, and also separately wheels. This uses a two modes of operation - manual and automatic. Given the urgency of the problem of forest fires, application of application of the offered design of a water curtain on fire fighter vehicle will al-low to reduce risk of ignition and protect equipment and people from the effects of a forest fire.

Download Full-text

Forced Zero Cross-Loading Misspecifications in Measurement Component of Structural Equation Models

Methodology ◽

10.1027/1614-2241/a000084 ◽

2014 ◽

Vol 10 (4) ◽

pp. 138-152 ◽

Cited By ~ 5

Author(s):

Hsien-Yuan Hsu ◽

Susan Troncoso Skidmore ◽

Yan Li ◽

Bruce Thompson

Keyword(s):

Structural Equation ◽

Structural Model ◽

Structural Equation Models ◽

Equation Model ◽

Model Fit ◽

Model Specification ◽

Simulation Design ◽

Measurement Models ◽

Fit Statistics ◽

Path Coefficients

The purpose of the present paper was to evaluate the effect of constraining near-zero parameter cross-loadings to zero in the measurement component of a structural equation model. A Monte Carlo 3 × 5 × 2 simulation design was conducted (i.e., sample sizes of 200, 600, and 1,000; parameter cross-loadings of 0.07, 0.10, 0.13, 0.16, and 0.19 misspecified to be zero; and parameter path coefficients in the structural model of either 0.50 or 0.70). Results indicated that factor pattern coefficients and factor covariances were overestimated in measurement models when near-zero parameter cross-loadings constrained to zero were higher than 0.13 in the population. Moreover, the path coefficients between factors were misestimated when the near-zero parameter cross-loadings constrained to zero were noteworthy. Our results add to the literature detailing the importance of testing individual model specification decisions, and not simply evaluating omnibus model fit statistics.

Download Full-text