scholarly journals Radiative Heating of a Glass Plate

2012 ◽  
Vol 5 (1) ◽  
pp. 1-30 ◽  
Author(s):  
Luc Paquet ◽  
Raouf El Cheikh ◽  
Dominique Lochegnies ◽  
Norbert Siedow
Keyword(s):  
Glass Plate ◽  
Radiative Heating

Radiative heating of a glass plate: the semi-discrete problem (second revision)

2018 ◽  
Vol 29 (1-2) ◽  
pp. 295-330
Author(s):  
Luc Paquet
Keyword(s):  
Glass Plate ◽  
Radiative Heating ◽  
Discrete Problem

Control of the radiative heating of a glass plate

2015 ◽  
Vol 27 (3-4) ◽  
pp. 673-699 ◽  
Author(s):  
Luc Paquet
Keyword(s):  
Glass Plate ◽  
Radiative Heating

Effects of compression during formation on the microstructure of composite hydroxylapatite/plaster implants for bone reconstruction

1988 ◽  
Vol 46 ◽  
pp. 750-751
Author(s):  
J. Hanker ◽  
K. Cowden ◽  
R. Noecker ◽  
P. Yates ◽  
N. Georgiade ◽  
...  
Keyword(s):  
Cosmetic Surgery ◽  
Glass Plate ◽  
Surgical Reconstruction ◽  
Equal Weight ◽  
Sintered Ceramic ◽  
Setting Times ◽  
Excess Water ◽  
Mixture Prior ◽  
Mechanical Strengths ◽  
Calcium Sulfate Hemihydrate

Composites of plaster of Paris (PP) and hydroxylapatite (HA) particles are being applied for the surgical reconstruction of craniofacial bone defects and for cosmetic surgery. Two types of HA particles are being employed, the dense sintered ceramic (DHA) and the porous, coralline hydroxylapatite (PHA) particles. Excess water is expressed out of the moistened HA/PP mixture prior to implantation and setting by pressing it in a non-tapered syringe against a glass plate. This results in implants with faster setting times and greater mechanical strengths. It was therefore of interest to compare samples of the compressed versus noncompressed mixtures to see whether or not any changes in their microstructure after setting could be related to these different properties.USG Medical Grade Calcium Sulfate Hemihydrate (which has the lowest mortar consistency of any known plaster) was mixed with an equal weight of Interpore 200 particles (a commercial form of PHA). After moistening with a minimum amount of water, disc-shaped noncompressed samples were made by filling small holes (0.339 in. diameter x 0.053 in. deep) in polypropylene molds with a microspatula.

Rate of Sublimation of Ice by Radiative Heating in Freeze-Etching

1980 ◽  
Vol 38 ◽  
pp. 618-619
Author(s):  
Yeshayahu Talmon
Keyword(s):  
Heat Flux ◽  
Freeze Fracture ◽  
Constant Heat Flux ◽  
Radiative Heating ◽  
Constant Heat ◽  
Entire Sample ◽  
Simplified Method ◽  
Freeze Etching ◽  
Sublimation Rates ◽  
Fractured Surface

To bring out details in the fractured surface of a frozen sample in the freeze fracture/freeze-etch technique,the sample or part of it is warmed to enhance water sublimation.One way to do this is to raise the temperature of the entire sample to about -100°C to -90°C. In this case sublimation rates can be calculated by using plots such as Fig.1 (Talmon and Thomas),or by simplified formulae such as that given by Menold and Liittge. To achieve higher rates of sublimation without heating the entire sample a radiative heater can be used (Echlin et al.). In the present paper a simplified method for the calculation of the rates of sublimation under a constant heat flux F [W/m2] at the surface of the sample from a heater placed directly above the sample is described.

Crack divergence phenomena in tempered glass

2020 ◽  
Vol 13 (3) ◽  
pp. 115-129
Author(s):  
Shin’ichi Aratani
Keyword(s):  
Optimal Design ◽  
High Speed ◽  
Glass Plate ◽  
Acute Angle ◽  
Divergence Angle ◽  
High Speed Photography ◽  
Tempered Glass ◽  
Thick Glass

High speed photography using the Cranz-Schardin camera was performed to study the crack divergence and divergence angle in thermally tempered glass. A tempered 3.5 mm thick glass plate was used as a specimen. It was shown that two types of bifurcation and branching existed as the crack divergence. The divergence angle was smaller than the value calculated from the principle of optimal design and showed an acute angle.

Radiative heating in scramjet combustors

10.2514/3.858 ◽  
1997 ◽  
Vol 11 ◽  
pp. 59-64
Author(s):  
Thomas Evrard ◽  
Richard Butler ◽  
Steven W. Hughes ◽  
J. Ranjan Banerjee ◽  
H. F. Nelson
Keyword(s):  
Radiative Heating ◽  
Scramjet Combustors

Influence of Atomic Lines on Radiative Heating of Entering Space Vehicles

2011 ◽  
Author(s):  
Sergey Surzhikov ◽  
Joseph Shang
Keyword(s):  
Radiative Heating ◽  
Space Vehicles ◽  
Atomic Lines

Characterization of Radiative Heating Anomaly in High Enthalpy Shock Tunnels

2021 ◽  
Author(s):  
Brett A. Cruden ◽  
Chun Y. Tang ◽  
Joseph Olejniczak ◽  
Adam J. Amar ◽  
Hideyuki Tanno
Keyword(s):  
Radiative Heating ◽  
High Enthalpy ◽  
Shock Tunnels ◽  
Heating Anomaly

A review of radiative heating in automated layup and its modelling

2017 ◽  
Vol 2 ◽  
pp. 91-125 ◽  
Author(s):  
Tilman Orth
Keyword(s):  
Radiative Heating
Sign in / Sign up

Export Citation Format

Share Document