Crystallization, structure, and enhanced mechanical property of ethylene‐octene elastomer crosslinked with dicumyl peroxide

2021 ◽  
pp. 50651
Author(s):  
Yuan‐Xia Wang ◽  
Ying Shi ◽  
Chen‐Chen Wang ◽  
Jia‐Hui Cheng ◽  
Ying Wang ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Dicumyl Peroxide ◽  
Crystallization Structure

Thermomechanical Treatment of a 4340 Ni-Cr-Mo Alloy Steel

1981 ◽  
Vol 39 ◽  
pp. 314-315 ◽  
Author(s):  
M.T. Jahn ◽  
J.C. Yang ◽  
C.M. Wan
Keyword(s):  
Mechanical Property ◽  
Chemical Composition ◽  
Alloy Steel ◽  
Thermomechanical Treatment ◽  
Room Temperature ◽  
Good Combination ◽  
Thermal Treatments ◽  
Low Carbon ◽  
4340 Steel ◽  
Good Improvement

4340 Ni-Cr-Mo alloy steel is widely used due to its good combination of strength and toughness. The mechanical property of 4340 steel can be improved by various thermal treatments. The influence of thermomechanical treatment (TMT) has been studied in a low carbon Ni-Cr-Mo steel having chemical composition closed to 4340 steel. TMT of 4340 steel is rarely examined up to now. In this study we obtain good improvement on the mechanical property of 4340 steel by TMT. The mechanism is explained in terms of TEM microstructures4340 (0.39C-1.81Ni-0.93Cr-0.26Mo) steel was austenitized at 950°C for 30 minutes. The TMTed specimen (T) was obtained by forging the specimen continuously as the temperature of the specimen was decreasing from 950°C to 600°C followed by oil quenching to room temperature. The thickness reduction ratio by forging is 40%. The conventional specimen (C) was obtained by quenching the specimen directly into room temperature oil after austenitized at 950°C for 30 minutes. All quenched specimens (T and C) were then tempered at 450, 500, 550, 600 or 650°C for four hours respectively.

Effects of hydrogen charging and electrotransport treatment on the anodic polarization behavior and mechanical property of Alloy 600

2015 ◽  
Vol 53 (11) ◽  
pp. 770-777
Author(s):  
Jung-Gu Kim ◽  
Jin-Seok Park ◽  
Yong-Sang Kim ◽  
Tae-Heum Nam
Keyword(s):  
Mechanical Property ◽  
Anodic Polarization ◽  
Alloy 600 ◽  
Hydrogen Charging ◽  
Polarization Behavior

Effect of pre-freezing rate on porosity ratio and mechanical property of pig aorta

10.2741/3945 ◽  
2012 ◽  
Vol 17 (1) ◽  
pp. 575 ◽  
Author(s):  
Meng Yin
Keyword(s):  
Mechanical Property ◽  
Freezing Rate ◽  
Porosity Ratio

Influence of crystallographic α-phase texture on mechanical property anisotropy of sheets made of pseudo-α and (α+β) titanium alloys

2020 ◽  
Vol 7 ◽  
pp. 20-25
Author(s):  
M. G. Isaenkova ◽  
◽  
O. A. Krymskaya ◽  
Ya. A. Babich ◽  
P. N. Medvedev ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Titanium Alloys ◽  
Α Phase ◽  
Property Anisotropy ◽  
Mechanical Property Anisotropy

Effect of milling on the microstructure and mechanical property of austenite stainless steel

2020 ◽  
Vol 62 (12) ◽  
pp. 1181-1186
Author(s):  
Huanchun Wu ◽  
Wenxin Ti ◽  
Guodong Zhang ◽  
Fei Xue ◽  
Chengtao Li ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Stainless Steel ◽  
Austenite Stainless Steel ◽  
Microstructure And Mechanical Property

EFFECT OF PRECURSOR MICROSTRUCTURE ON MORPHOLOGY FEATURE AND MECHANICAL PROPERTY OF C-Mn-Si STEEL

2013 ◽  
Vol 49 (12) ◽  
pp. 1558 ◽  
Author(s):  
Yongqiang REN ◽  
Zhenjia XIE ◽  
Hongwei ZHANG ◽  
Shengfu YUAN ◽  
Tingting SONG ◽  
...  
Keyword(s):  
Mechanical Property

Microstructural and mechanical property characterization of ingot metallurgy ODS iron aluminide

1997 ◽  
Author(s):  
V K Sikka ◽  
C R Howell ◽  
F Hall ◽  
J Valykeo
Keyword(s):  
Mechanical Property ◽  
Iron Aluminide ◽  
Ingot Metallurgy ◽  
Property Characterization

Mechanical Property Studies on Flax Fiber Reinforced Basalt Powder Filled Polyester Composite

2020 ◽  
Vol 13 ◽  
Author(s):  
V. Arumugaprabu ◽  
K.Arun Prasath ◽  
S. Mangaleswaran ◽  
M. Manikanda Raja ◽  
R. Jegan
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Natural Fiber ◽  
Tensile Load ◽  
Flax Fiber ◽  
Flexural Properties ◽  
Weight Percentage ◽  
Tensile Impact ◽  
Polyester Composite ◽  
Additional Support

: The objective of this research is to evaluate the tensile, impact and flexural properties of flax fiber and basalt powder filled polyester composite. Flax fiber is one of the predominant reinforcement natural fiber which possess good mechanical properties and addition of basalt powder as a filler provides additional support to the composite. The Composites are prepared using flax fiber arranged in 10 layers with varying weight percentage of the basalt powder as 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.% and 30 wt.% respectively. From the results it is inferred that the composite combination 10 Layers of flax / 5 wt.%, basalt Powder absorbs more tensile load of 145 MPa. Also, for the same combination maximum flexural strength is about 60 MPa. Interestingly in the case of impact strength more energy was absorbed by 10 layers of flax and 30 wt.% of basalt powder. In addition, the failure mechanism of the composites also discussed briefly using SEM studies.

Vulcanization of natural rubber by dicumyl peroxide in the presence of sulphur

1973 ◽  
Vol 38 (2) ◽  
pp. 408-416 ◽  
Author(s):  
B. Bakule ◽  
J. Honskus ◽  
J. Nedbal ◽  
P. Zinburg
Keyword(s):  
Natural Rubber ◽  
Dicumyl Peroxide

scholarly journals Trade-off of rapid recrystallization and mechanical property improvement of Ti-6Al-4V alloy

2019 ◽  
Vol 15 ◽  
pp. 102722
Author(s):  
Hui Shao ◽  
Di Shan ◽  
Kaixuan Wang ◽  
Guojun Zhang ◽  
Yongqing Zhao
Keyword(s):  
Mechanical Property ◽  
Trade Off
Sign in / Sign up

Export Citation Format

Share Document