A New Kinematic Hardening Rule Describing Different Plastic Moduli in Monotonic and Cyclic Deformations

2015 ◽  
pp. 587-601 ◽  
Author(s):  
Yilin Zhu ◽  
Guozheng Kang ◽  
Qianhua Kan
Keyword(s):  
Kinematic Hardening ◽  
Hardening Rule

Ratcheting behavior of cylindrical pipes based on the Chaboche kinematic hardening rule

2012 ◽  
Vol 26 (10) ◽  
pp. 3073-3079 ◽  
Author(s):  
H. Badnava ◽  
H. R. Farhoudi ◽  
Kh. Fallah Nejad ◽  
S. M. Pezeshki
Keyword(s):  
Kinematic Hardening ◽  
Hardening Rule

Cyclic Plasticity for Nonproportional Paths: Part 2—Comparison With Predictions of Three Incremental Plasticity Models

1978 ◽  
Vol 100 (1) ◽  
pp. 104-111 ◽  
Author(s):  
H. S. Lamba ◽  
O. M. Sidebottom
Keyword(s):  
Cyclic Loading ◽  
Material Property ◽  
Yield Surface ◽  
Strain Path ◽  
Kinematic Hardening ◽  
Cyclic Plasticity ◽  
Limit Surface ◽  
Hardening Rule ◽  
Hardening Models ◽  
Hardening Rules

Experiments that demonstrate the basic quantitative and qualitative aspects of the cyclic plasticity of metals are presented in Part 1. Three incremental plasticity kinematic hardening models of prominence are based on the Prager, Ziegler, and Mroz hardening rules, of which the former two have been more frequently used than the latter. For a specimen previously fully stabilized by out of phase cyclic loading the results of a subsequent cyclic nonproportional strain path experiment are compared to the predictions of the above models. A formulation employing a Tresca yield surface translating inside a Tresca limit surface according to the Mroz hardening rule gives excellent predictions and also demonstrates the erasure of memory material property.

Elastic-Plastic Analysis of Fretting Contacts

2015 ◽  
Vol 642 ◽  
pp. 248-252
Author(s):  
Chang Hung Kuo
Keyword(s):  
Kinematic Hardening ◽  
Carbon Steels ◽  
Plastic Behavior ◽  
Rule Based ◽  
Elastic Plastic ◽  
Hardening Rule ◽  
Chaboche Model ◽  
Plastic Analysis ◽  
Finite Element Procedure ◽  
Elastic Shakedown

A finite element procedure is implemented for the elastic-plastic analysis of carbon steels subjected to reciprocating fretting contacts. The nonlinear kinematic hardening rule based on Chaboche model is used to model the cyclic plastic behavior in fretting contacts. The results show that accumulation of plastic strains, i.e. ratchetting, may occur near the contact edge while elastic shakedown is likely to take place in substrate.

A Generalized Anisotropic Hardening Rule Based on the Mroz Multi-Yield-Surface Model

2008 ◽  
Author(s):  
K. S. Choi ◽  
J. Pan
Keyword(s):  
Cyclic Loading ◽  
Yield Surface ◽  
Kinematic Hardening ◽  
Constitutive Relations ◽  
Yield Function ◽  
Surface Model ◽  
Loading Conditions ◽  
Anisotropic Hardening ◽  
Hardening Rule ◽  
Strain Data

In this paper, a generalized anisotropic hardening rule based on the Mroz multi-yield-surface model is derived. The evolution equation for the active yield surface is obtained by considering the continuous expansion of the active yield surface during the unloading/reloading process. The incremental constitutive relation based on the associated flow rule is then derived for a general yield function. As a special case, detailed incremental constitutive relations are derived for the Mises yield function. The closed-form solutions for one-dimensional stress-plastic strain curves are also derived and plotted for the Mises materials under cyclic loading conditions. The stress-plastic strain curves show closed hysteresis loops under uniaxial cyclic loading conditions and the Masing hypothesis is applicable. A user material subroutine based on the Mises yield function, the anisotropic hardening rule and the constitutive relations was then written and implemented into ABAQUS. Computations were conducted for a simple plane strain finite element model under uniaxial monotonic and cyclic loading conditions based on the anisotropic hardening rule and the isotropic and nonlinear kinematic hardening rules of ABAQUS. The results indicate that the plastic response of the material follows the intended input stress-strain data for the anisotropic hardening rule whereas the plastic response depends upon the input strain ranges of the stress-strain data for the nonlinear kinematic hardening rule.

An Expression of Elastic-Plastic Constitutive Law Incorporating Vertex Formation and Kinematic Hardening

1991 ◽  
Vol 58 (3) ◽  
pp. 617-622 ◽  
Author(s):  
Moriaki Goya ◽  
Koichi Ito
Keyword(s):  
Kinematic Hardening ◽  
Sufficient Conditions ◽  
Constitutive Law ◽  
Elastic Plastic ◽  
Hardening Rule ◽  
Direction Angle ◽  
Plastic Materials ◽  
Path Direction ◽  
Elastic Plastic Materials ◽  
Linear Loading

A phenomenological corner theory was proposed for elastic-plastic materials by the authors in the previous paper (Goya and Ito, 1980). The theory was developed by introducing two transition parameters, μ (α) and β (α), which, respectively, denote the normalized magnitude and direction angle of plastic strain increments, and both monotonously vary with the direction angle of stress increments. The purpose of this report is to incorporate the Bauschinger effect into the above theory. This is achieved by the introduction of Ziegler’s kinematic hardening rule. To demonstrate the validity and applicability of a newly developed theory, we analyze the bilinear strain-path problem using the developed equation, in which, after some linear loading, the path is abruptly changed to various directions. In the calculation, specific functions, such as μ (α) = Cos (.5πα/αmax) and β (α) = (αmax- .5π) α/αmax, are chosen for the transition parameters. As has been demonstrated by numerous experimental research on this problem, the results in this report also show a distinctive decrease of the effective stress just after the change of path direction. Discussions are also made on the uniqueness of the inversion of the constitutive equation, and sufficient conditions for such uniqueness are revealed in terms of μ(α), β(α) and some work-hardening coefficients.

scholarly journals Effect of Strain Gradient on Formation of Shear Band under Kinematic Hardening Rule

2004 ◽  
Vol 47 (2) ◽  
pp. 223-231
Author(s):  
Su-Jin YUN
Keyword(s):  
Shear Band ◽  
Strain Gradient ◽  
Kinematic Hardening ◽  
Hardening Rule

Experimental and Numerical Study of Uniaxial and Multiaxial Stress-Strain Behaviour of R7T Wheel Steel

2015 ◽  
Vol 732 ◽  
pp. 91-94 ◽  
Author(s):  
Radim Halama ◽  
Michal Šofer ◽  
František Fojtík ◽  
Aleksandros Markopoulos
Keyword(s):  
Numerical Study ◽  
Kinematic Hardening ◽  
Wheel Steel ◽  
Isotropic Hardening ◽  
Good Prediction ◽  
Main Attention ◽  
Stress Strain ◽  
Strain Behavior ◽  
Hardening Rule ◽  
Strain Behaviour

This paper is focused on the correct description of stress-strain behavior of the R7T steel. An experimental study on the wheel steel specimens including uniaxial as well as multiaxial tests has been conducted. The main attention was paid to such effects as ratcheting and nonproportional hardening of the material. A cyclically stable behavior of the steel under higher amplitude loading was found. The MAKOC model, which is based on AbdelKarim-Ohno kinematic hardening rule and Calloch isotropic hardening rule, has been applied in subsequent finite element simulations. The numerical results show very good prediction of stress-strain behaviour of the wheel steel.

scholarly journals Ratcheting Simulation in a Titanium-Steel Bimetallic Plate Based on the Chaboche Hardening Model

2016 ◽  
Vol 10 (4) ◽  
pp. 265-270
Author(s):  
Aleksander Karolczuk
Keyword(s):  
Residual Stresses ◽  
Kinematic Hardening ◽  
Fatigue Loading ◽  
Experimental Results ◽  
Hardening Model ◽  
The Third ◽  
Hardening Rule ◽  
Bimetallic Plate

Abstract The paper presents the results of fatigue loading simulation applied to bimetallic model using the Chaboche kinematic hardening rule. Three cases of simulations were performed: (i) without residual stresses; (ii) considering residual stresses and (iii) considering asymmetrical geometry of bimetal, i.e. cross area reducing under tension period of loading. Experimental results exhibit the ratcheting phenomenon in titanium-steel bimetallic specimens. The observed ratcheting phenomenon could be explained by the third case of simulation which is supported by detection of microcracks in the vicinity of welded area.

Sign in / Sign up

Export Citation Format

Share Document