Nested Iteration Technique

Author(s):  
Wolfgang Hackbusch
1995 ◽  
Vol 45 (2) ◽  
pp. 245-254 ◽  
Author(s):  
Jae Sung Lim ◽  
Chul Heum Yon ◽  
Chong Kwan Un

Author(s):  
Jasdev Bhatti ◽  
Mohit Kumar Kakkar

Background and Aim: With an increase in demands about reliability of industrial machines following continuous or discrete distribution, the important thing to be noticed is that in all previous researches where systems are having more than one failure no iteration technique has been studied to separate the failed unit on basis of its failure. Therefore, aim of our paper is to analyze the real industrial discrete problem following cold standby units arranged in parallel manner with newly concept of inspection procedure for failed units to inspect the exact failure and being communicator to the repairman for repairing exact failed part of unit for saving time and maintenance cost. Methods: The geometric distribution and regenerative techniques had been applied for calculating different reliability measures like mean time to system failure, availability of a system, inspection, repair and failed time of unit. Results: Graphical and analytical study had also been done to analyze the increasing/decreasing behavior of profit function w.r.t repair and failure rate. The system responded properly in fulfilling his basic needs. Conclusion: The calculated value of all reliability parameter is helpful for studying any other models following same concept under different environmental conditions. Thus, it concluded that, reliability increases/decreases with increase in repair/failure rate. Also, the evaluated results by this paper provides the better reliability testing strategies that helps to develop new techniques which leads to increase the effectiveness of system.


1973 ◽  
Vol 24 (2) ◽  
pp. 120-128 ◽  
Author(s):  
J E Barsby

SummarySolutions to the problem of separated flow past slender delta wings for moderate values of a suitably defined incidence parameter have been calculated by Smith, using a vortex sheet model. By increasing the accuracy of the finite-difference technique, and by replacing Smith’s original nested iteration procedure, to solve the non-linear simultaneous equations that arise, by a Newton’s method, it is possible to extend the range of the incidence parameter over which solutions can be obtained. Furthermore for sufficiently small values of the incidence parameter, new and unexpected results in the form of vortex systems that originate inboard from the leading edge have been discovered. These new solutions are the only solutions, to the author’s knowledge, of a vortex sheet leaving a smooth surface.Interest has centred upon the shape of the finite vortex sheet, the position of the isolated vortex, and the lift, and variations of these quantities are shown as functions of the incidence parameter. Although no experimental evidence is available, comparisons are made with the simpler Brown and Michael model in which all the vorticity is assumed to be concentrated onto an isolated line vortex. Agreement between these two models becomes very close as the value of the incidence parameter is reduced.


1990 ◽  
Vol 13 (2) ◽  
pp. 315-319
Author(s):  
H. A. S. Abujabal ◽  
M. S. Khan

Through much shorter proofs, some new commutativity theorems for rings with unity have been obtained. These results either extend or generalize a few well-known theorems. Our method of proof is based on an iteration technique.


Author(s):  
Amin Gholami ◽  
Davood D. Ganji ◽  
Hadi Rezazadeh ◽  
Waleed Adel ◽  
Ahmet Bekir

Abstract The paper deals with the application of a strong method called the modified Mickens iteration technique which is used for solving a strongly nonlinear system. The system describes the motion of a simple mathematical pendulum with a particle attached to it through a stretched wire. This model has great applications especially in the area of nonlinear vibrations and oscillation systems. The proposed method depends on determining the frequency and amplitude of the system through the modified Mickens iterative approach which is a modification of the regular Mickens approach. The preliminaries of the proposed technique are present and the application to the model is discussed. The method depends on the Mickens iteration approach which transforms the considered equation into a linear form and then is solving this equation result in the approximate solution. Some examples are given to validate and illustrate the effectiveness and convenience of the method. These results are compared with other relative techniques from the literature in terms of finding the frequency of the two examined models. The method produces more accurate results when compared to these methods and is considered a strong candidate for solving other nonlinear problems with applications in science and engineering.


2010 ◽  
Vol 32 (3) ◽  
pp. 1506-1526 ◽  
Author(s):  
J. H. Adler ◽  
T. A. Manteuffel ◽  
S. F. McCormick ◽  
J. W. Ruge ◽  
G. D. Sanders

Sign in / Sign up

Export Citation Format

Share Document