Effect of Dual-Sided Laser Peening Modes on Residual Stress Distribution of Aero-engine Titanium Blades

2018 ◽  
pp. 29-45
Author(s):  
Peixuan Ouyang ◽  
Liangju He ◽  
Peijie Li ◽  
Guangbao Mi
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stress Distribution ◽  
Laser Peening ◽  
Aero Engine

Application of Indirect Laser Peening to SUS304 Stainless Steel

2014 ◽  
Vol 783-786 ◽  
pp. 2316-2321
Author(s):  
Hiroshi Kawakami ◽  
Akiyoshi Kondo ◽  
Muneharu Kutsuna ◽  
Kiyotaka Saito ◽  
Hiroki Inoue ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Stress Distribution ◽  
Pulse Energy ◽  
Laser Power ◽  
Compressive Residual Stress ◽  
Residual Stress Distribution ◽  
Bending Test ◽  
Laser Peening

Indirect laser peening applied to the substrate of austenitic stainless steel with the sheet of similar material. Effects of indirect laser peening condition on the formation of the dimple and the residual stress were investigated in this paper. Shape of the dimple and distribution of the residual stress were measured by laser microscope and X-ray diffraction, respectively. It was observed by the microscope that clean substrate surface of as-received state kept after indirect laser peening because of protection by the sheet. However, fracture of sheet occurred slightly in high pulse energy condition. The diameter and the depth of the dimple by indirect laser peening increased with the increase of laser power. Efficiency of dimple formation decreased with the increase of pulse energy. Affective condition region of indirect laser peening with a combination between the substrate and the sheet of austenitic stainless steel may be limited below the laser power density of 10GW/cm2. It was confirmed that indirect laser peening induced compressive residual stress in the substrate. One of peak of compressive residual stress in residual stress distribution existed near the bottom of the dimple. Residual stress distribution which was produced by indirect laser peening may affect change of quasi bending modulus which was obtained by three-point bending test.

scholarly journals Residual Stress Distribution and Microstructure Evolution of AA 6061-T6 Treated by Warm Laser Peening

Metals ◽  
2016 ◽  
Vol 6 (11) ◽  
pp. 292 ◽  
Author(s):  
Shu Huang ◽  
Zuowei Wang ◽  
Jie Sheng ◽  
Emmanuel Agyenim-Boateng ◽  
Muxi Liu ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Microstructure Evolution ◽  
Residual Stress Distribution ◽  
Laser Peening

Investigation of Residual Stress Distribution in Clad 2024 T3 after Laser Peening

2012 ◽  
Vol 525-526 ◽  
pp. 125-128
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Copyright Owner ◽  
Residual Stress Distribution ◽  
Laser Peening

This paper was retracted by the authors and publisher since it contained material used without the permission of Cranfield University, the copyright owner.

Residual stress distribution in laser alloying zone with FeCSiB powder

2008 ◽  
Author(s):  
Zhengyang Li ◽  
Haiyan Zhao ◽  
Minlin Zhong ◽  
Bin Zhang ◽  
Yu Gu ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stress Distribution ◽  
Laser Alloying

The Measurement Method of Internal Residual Stress Distribution Concerned with Fatigue Crack Growth

2016 ◽  
Vol 85 (2) ◽  
pp. 216-220
Author(s):  
Shinji KAWAI ◽  
Takuya NAGAI ◽  
Shigetaka OKANO ◽  
Masahito MOCHIZUKI
Keyword(s):  
Residual Stress ◽  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Stress Distribution ◽  
Crack Growth ◽  
Measurement Method ◽  
Residual Stress Distribution

Influence of the Welded Joint on the Mechanical Behavior of Steel Piles during Static and Dynamic Deformation

2007 ◽  
Vol 345-346 ◽  
pp. 1469-1472
Author(s):  
Gab Chul Jang ◽  
Kyong Ho Chang ◽  
Chin Hyung Lee
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Mechanical Behavior ◽  
Welded Joint ◽  
Dynamic Deformation ◽  
Three Dimensional ◽  
Steel Structures ◽  
Residual Stress Distribution ◽  
Dynamic Mechanical Behavior ◽  
Steel Piles

During manufacturing the welded joint of steel structures, residual stress is produced and weld metal is used inevitably. And residual stress and weld metal influence on the static and dynamic mechanical behavior of steel structures. Therefore, to predict the mechanical behavior of steel pile with a welded joint during static and dynamic deformation, the research on the influence of the welded joints on the static and dynamic behavior of steel pile is clarified. In this paper, the residual stress distribution in a welded joint of steel piles was investigated by using three-dimensional welding analysis. The static and dynamic mechanical behavior of steel piles with a welded joint is investigated by three-dimensional elastic-plastic finite element analysis using a proposed dynamic hysteresis model. Numerical analyses of the steel pile with a welded joint were compared to that without a welded joint with respect to load carrying capacity and residual stress distribution. The influence of the welded joint on the mechanical behavior of steel piles during static and dynamic deformation was clarified by comparing analytical results

scholarly journals A study on the optimization of residual stress distribution in the polyethylene and polyketone double layer pipes

2021 ◽  
pp. 101547
Author(s):  
A.G. Ramu ◽  
Sunwoo Kim ◽  
Heungwoo Jeon ◽  
Amal M. Al-Mohaimeed ◽  
Wedad A. Al-onazi ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Double Layer ◽  
Residual Stress Distribution
Sign in / Sign up

Export Citation Format

Share Document