Effect of Heat Treatment on Formability of AA6082 by Single Point Incremental Forming

2019 ◽  
pp. 3-15
Author(s):  
S. Maharajan ◽  
D. Ravindran ◽  
S. Rajakarunakaran
Keyword(s):  
Heat Treatment ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming

Single Point Incremental Forming of an Aged AL-Cu-Mg Alloy: Influence of Pre-heat Treatment and Warm Forming

2016 ◽  
Vol 25 (6) ◽  
pp. 2478-2488 ◽  
Author(s):  
Amirahmad Mohammadi ◽  
Ling Qin ◽  
Hans Vanhove ◽  
Marc Seefeldt ◽  
Albert Van Bael ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Incremental Forming ◽  
Single Point ◽  
Warm Forming ◽  
Mg Alloy ◽  
Single Point Incremental Forming

Improve the Micro-hardness of Single Point Incremental Forming Product Using Magnetic Abrasive Finishing

2020 ◽  
Vol 38 (8A) ◽  
pp. 1137-1142
Author(s):  
Baqer A. Ahmed ◽  
Saad K. Shather ◽  
Wisam K. Hamdan
Keyword(s):  
Vickers Hardness ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Step Size ◽  
Coil Current ◽  
Magnetic Abrasive Finishing ◽  
Finishing Process ◽  
Abrasive Finishing

In this paper the Magnetic Abrasive Finishing (MAF) was utilized after Single Point Incremental Forming (SPIF) process as a combined finishing process. Firstly, the Single Point Incremental forming was form the truncated cone made from low carbon steel (1008-AISI) based on Z-level tool path then the magnetic abrasive finishing process was applied on the surface of the formed product. Box-Behnken design of experiment in Minitab 17 software was used in this study. The influences of different parameters (feed rate, machining step size, coil current and spindle speed) on change in Micro-Vickers hardness were studied. The maximum and minimum change in Micro-Vickers hardness that achieved from all the experiments were (40.4 and 1.1) respectively. The contribution percent of (feed rate, machining step size, coil current and spindle speed) were (7.1, 18.068, 17.376 and 37.894) % respectively. After MAF process all the micro surface cracks that generated on the workpiece surface was completely removed from the surface.

Hot single-point incremental forming assisted by induction heating

2015 ◽  
Vol 82 (5-8) ◽  
pp. 1163-1171 ◽  
Author(s):  
Amar Al-Obaidi ◽  
Verena Kräusel ◽  
Dirk Landgrebe
Keyword(s):  
Induction Heating ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming

Multiobjective optimization of process variables in single-point incremental forming using grey relational analysis coupled with entropy weights

2021 ◽  
pp. 146442072110204
Author(s):  
Abdulmajeed Dabwan ◽  
Adham E Ragab ◽  
Mohamed A Saleh ◽  
Atef M Ghaleb ◽  
Mohamed Z Ramadan ◽  
...  
Keyword(s):  
Grey Relational Analysis ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Numerical Control ◽  
Single Point Incremental Forming ◽  
Process Variables ◽  
Relational Analysis ◽  
Grey Relational

Incremental sheet forming is a specific group of sheet forming methods that enable the manufacture of complex parts utilizing computer numerical control instead of specialized tools. It is an incredibly adaptable operation that involves minimal usage of sophisticated tools, dies, and forming presses. Besides its main application in the field of rapid prototyping, incremental sheet forming processes can be used for the manufacture of unique parts in small batches. The goal of this study is to broaden the knowledge of the deformation process in single-point incremental forming. This work studies the deformation behavior in single-point incremental forming by experimentally investigating the principal stresses, principal strains, and thinning of single-point incremental forming products. Conical-shaped components are fabricated using AA1050-H14 aluminum alloy at various combinations of fundamental variables. The factorial design is employed to plan the experimental study and analysis of variance is conducted to analyze the results. The grey relational analysis approach coupled with entropy weights is also implemented to identify optimum process variables for single-point incremental forming. The results show that the tool diameter has the greatest effect on the thinning of the SPIF product, followed by the sheet thickness, step size, and feed rate.

Studies on single point incremental forming of Ti-6Al-4V alloy for aerospace applications

2020 ◽  
Vol 22 ◽  
pp. 1967-1976
Author(s):  
C. Veera ajay ◽  
S. Elangovan ◽  
C.T. Justus Panicker
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Aerospace Applications

scholarly journals Characterisation of geometrical and physical properties of a stainless steel denture framework manufactured by single-point incremental forming

2021 ◽  
Vol 10 ◽  
pp. 605-623
Author(s):  
Mladomir Milutinović ◽  
Robert Lendjel ◽  
Sebastian Baloš ◽  
Danka Labus Zlatanović ◽  
Luka Sevšek ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Physical Properties ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming

Progress on single-point incremental forming of polymers

2021 ◽  
Vol 114 (1-2) ◽  
pp. 1-26
Author(s):  
Malik Hassan ◽  
G. Hussain ◽  
Hongyu Wei ◽  
Abdul Qadeer ◽  
Mohammed AlKahtani
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming
Sign in / Sign up

Export Citation Format

Share Document