Contact problems for a half plane with initial stress reinforced by elastic facings

1985 ◽  
Vol 21 (3) ◽  
pp. 269-277
Author(s):  
A. N. Guz' ◽  
V. B. Rudnitskii
Keyword(s):  
Initial Stress ◽  
Half Plane ◽  
Contact Problems

Thermal Distortion of an Anisotropic Elastic Half-Plane and its Application in Contact Problems Including Frictional Heating

2005 ◽  
Vol 128 (1) ◽  
pp. 32-39 ◽  
Author(s):  
Yuan Lin ◽  
Timothy C. Ovaert
Keyword(s):  
Heat Flux ◽  
Half Plane ◽  
Frictional Heating ◽  
Contact Problems ◽  
Local Heat ◽  
Extended Version ◽  
Parabolic Profile ◽  
Local Heat Flux ◽  
Anisotropic Elastic ◽  
Thermoelastic Contact Problem

The thermal surface distortion of an anisotropic elastic half-plane is studied using the extended version of Stroh’s formalism. In general, the curvature of the surface depends both on the local heat flux into the half-plane and the local temperature variation along the surface. However, if the material is orthotropic, the curvature of the surface depends only on the local heat flux into the half-plane. As a direct application, the two-dimensional thermoelastic contact problem of an indenter sliding against an orthotropic half-plane is considered. Two cases, where the indenter has either a flat or a parabolic profile, are studied in detail. Comparisons with other available results in the literature show that the present method is correct and accurate.

scholarly journals A Paradox in Sliding Contact Problems With Friction

2003 ◽  
Vol 72 (3) ◽  
pp. 450-452 ◽  
Author(s):  
G. G. Adams ◽  
J. R. Barber ◽  
M. Ciavarella ◽  
J. R. Rice
Keyword(s):  
Half Plane ◽  
Slip Velocity ◽  
Finite Strain ◽  
Applied Pressure ◽  
Strain Analysis ◽  
Contact Problems ◽  
Rigid Punch ◽  
Flat Punch ◽  
Relative Slip ◽  
Velocity Changes

In problems involving the relative sliding to two bodies, the frictional force is taken to oppose the direction of the local relative slip velocity. For a rigid flat punch sliding over a half-plane at any speed, it is shown that the velocities of the half-plane particles near the edges of the punch seem to grow without limit in the same direction as the punch motion. Thus the local relative slip velocity changes sign. This phenomenon leads to a paradox in friction, in the sense that the assumed direction of sliding used for Coulomb friction is opposite that of the resulting slip velocity in the region sufficiently close to each of the edges of the punch. This paradox is not restricted to the case of a rigid punch, as it is due to the deformations in the half-plane over which the pressure is moving. It would therefore occur for any punch shape and elastic constants (including an elastic wedge) for which the applied pressure, moving along the free surface of the half-plane, is singular. The paradox is resolved by using a finite strain analysis of the kinematics for the rigid punch problem and it is expected that finite strain theory would resolve the paradox for a more general contact problem.

Thermal Distortion of an Anisotropic Elastic Half-Plane and Its Application in Contact Problems Including Frictional Heating

2004 ◽  
Author(s):  
Yuan Lin ◽  
Timothy C. Ovaert
Keyword(s):  
Heat Flux ◽  
Half Plane ◽  
Frictional Heating ◽  
Contact Problems ◽  
Local Heat ◽  
Extended Version ◽  
Parabolic Profile ◽  
Local Heat Flux ◽  
Anisotropic Elastic ◽  
Thermoelastic Contact Problem

The thermal surface distortion of an anisotropic elastic half-plane is studied using the extended version of Stroh’s formalism. In general, the curvature of the surface depends both on the local heat flux into the half-plane and the local temperature variation along the surface. However, if the material is orthotropic, the curvature of the surface depends only on the local heat flux into the half-plane. As a direct application, the two-dimensional thermoelastic contact problem of an indenter sliding against an orthotropic half-plane is considered. Two cases, where the indenter has either a flat or a parabolic profile, are studied in detail. Comparisons with other available results in the literature show that the present method is correct and accurate.

Sign in / Sign up

Export Citation Format

Share Document