Calculation and analysis of kinetic curves for biporous adsorbents with linear adsorption isotherms. 2. Analysis of results

1977 ◽  
Vol 26 (12) ◽  
pp. 2456-2459
Author(s):  
P. P. Zolotarev ◽  
L. I. Kataeva ◽  
V. I. Ulin
Keyword(s):  
Adsorption Isotherms ◽  
Kinetic Curves ◽  
Analysis Of Results

Preparation of Novel Nanocarbon Spheres and Study on Adsorption Isotherms

2020 ◽  
Author(s):  
Aili Ma ◽  
Chengqian Li ◽  
Wuqing Du ◽  
Jie Chang
Keyword(s):  
Adsorption Isotherms

Analysis of some adsorption isotherms on calcium silicate hydrates

1977 ◽  
Vol 27 (1) ◽  
pp. 48-54
Author(s):  
Gerald C. Bye ◽  
Gilbert O. Chigbo
Keyword(s):  
Adsorption Isotherms ◽  
Calcium Silicate ◽  
Calcium Silicate Hydrates

Adsorption of metal cations on wool carbonising waste. Part 1. Adsorption isotherms

1981 ◽  
Vol 31 (1) ◽  
pp. 597-601 ◽  
Author(s):  
Karim Farag ◽  
Francis Perineau ◽  
Antoine Gaset ◽  
Jacques Molinier
Keyword(s):  
Adsorption Isotherms ◽  
Metal Cations

Modification of tundish design to improve quality of slabs, casted at CCM No. 4 of EVRAZ NTMK

2020 ◽  
Vol 76 (6) ◽  
pp. 559-563
Author(s):  
I. M. Zakharov ◽  
V. A. Smirnov ◽  
D. V. Sushnikov ◽  
A. G. Lyzhin ◽  
E. A. Lavrova ◽  
...  
Keyword(s):  
Basic Number ◽  
Metal Level ◽  
Surface Layers ◽  
Secondary Oxidation ◽  
Strip Rolling ◽  
Actual Distribution ◽  
Ultrasonic Control ◽  
Analysis Of Results ◽  
Water Simulation

A technology of continuous casting of steel has a large effect on its contamination. In particular, proper organization of metal flows in tundish and mold is very important. After completion a series of casting through a tundish and drop of metal level in it, it possible, that the slag flows from the surface layers of the tundish to capture the metal. An analysis of results of ultrasonic control of finished strip showed, that the basic number of the revealed defects was obtained during strip rolling out of the last slabs of the last heat in a series for a tundish. Metallographic studies determined, that the defects were located in the slab axis zone and filled by macro-inclusions of complex composition. To determine the actual distribution of metal flows, a water simulation of them was accomplished for the existing design of the EVRAZ NTMK tundish. It was determined, that at the drop of metal level in a tundish, a capture of slag from the metal reservoir and its transfer into the main bath of the tundish takes place due to whirligig flows. Following the weight metal consumption, the zone of slag inclusions distribution enlarges. Besides, denudation of the metal mirror in the metal reservoir takes place, resulted in metal secondary oxidation. Based on the results of the simulation, it was proposed to modify the design of the “turbostop”, which is installed in the metal reservoir of the tundish. Besides, it was proposed to remove the dividers installation in the tundish. It was noted, that the proposed steps enable to ensure a minimal level of rejections.

Adsorption isotherms of insulin onto various materials

Diabetes ◽  
1984 ◽  
Vol 33 (7) ◽  
pp. 674-680 ◽  
Author(s):  
M. V. Sefton ◽  
G. M. Antonacci
Keyword(s):  
Adsorption Isotherms
Sign in / Sign up

Export Citation Format

Share Document