Lumbar Microdiscectomy With Medial Facetectomy: Techniques and Analysis of Results

1993 ◽  
Vol 4 (1) ◽  
pp. 109-115 ◽  
Author(s):  
R. Tyler Frizzell ◽  
Mark N. Hadley
Keyword(s):  
Lumbar Microdiscectomy ◽  
Analysis Of Results

Modification of tundish design to improve quality of slabs, casted at CCM No. 4 of EVRAZ NTMK

2020 ◽  
Vol 76 (6) ◽  
pp. 559-563
Author(s):  
I. M. Zakharov ◽  
V. A. Smirnov ◽  
D. V. Sushnikov ◽  
A. G. Lyzhin ◽  
E. A. Lavrova ◽  
...  
Keyword(s):  
Basic Number ◽  
Metal Level ◽  
Surface Layers ◽  
Secondary Oxidation ◽  
Strip Rolling ◽  
Actual Distribution ◽  
Ultrasonic Control ◽  
Analysis Of Results ◽  
Water Simulation

A technology of continuous casting of steel has a large effect on its contamination. In particular, proper organization of metal flows in tundish and mold is very important. After completion a series of casting through a tundish and drop of metal level in it, it possible, that the slag flows from the surface layers of the tundish to capture the metal. An analysis of results of ultrasonic control of finished strip showed, that the basic number of the revealed defects was obtained during strip rolling out of the last slabs of the last heat in a series for a tundish. Metallographic studies determined, that the defects were located in the slab axis zone and filled by macro-inclusions of complex composition. To determine the actual distribution of metal flows, a water simulation of them was accomplished for the existing design of the EVRAZ NTMK tundish. It was determined, that at the drop of metal level in a tundish, a capture of slag from the metal reservoir and its transfer into the main bath of the tundish takes place due to whirligig flows. Following the weight metal consumption, the zone of slag inclusions distribution enlarges. Besides, denudation of the metal mirror in the metal reservoir takes place, resulted in metal secondary oxidation. Based on the results of the simulation, it was proposed to modify the design of the “turbostop”, which is installed in the metal reservoir of the tundish. Besides, it was proposed to remove the dividers installation in the tundish. It was noted, that the proposed steps enable to ensure a minimal level of rejections.

Verification of the Calculation Assumptions Applied to Solutions of the Acoustic Measurements Uncertainty

2015 ◽  
Vol 39 (2) ◽  
pp. 199-202
Author(s):  
Wojciech Batko ◽  
Renata Bal
Keyword(s):  
Normal Distribution ◽  
Confidence Intervals ◽  
Uncertainty Of Measurement ◽  
Acoustic Measurements ◽  
Uncertainty In Measurement ◽  
Sound Levels ◽  
Measurement Results ◽  
Analysis Of Results ◽  
Essential Problem ◽  
Expression Of Uncertainty

Abstract The assessment of the uncertainty of measurement results, an essential problem in environmental acoustic investigations, is undertaken in the paper. An attention is drawn to the - usually omitted - problem of the verification of assumptions related to using the classic methods of the confidence intervals estimation, for the controlled measuring quantity. Especially the paper directs attention to the need of the verification of the assumption of the normal distribution of the measuring quantity set, being the base for the existing and binding procedures of the acoustic measurements assessment uncertainty. The essence of the undertaken problem concerns the binding legal and standard acts related to acoustic measurements and recommended in: 'Guide to the expression of uncertainty in measurement' (GUM) (OIML 1993), developed under the aegis of the International Bureau of Measures (BIPM). The model legitimacy of the hypothesis of the normal distribution of the measuring quantity set in acoustic measurements is discussed and supplemented by testing its likelihood on the environment acoustic results. The Jarque-Bery test based on skewness and flattening (curtosis) distribution measures was used for the analysis of results verifying the assumption. This test allows for the simultaneous analysis of the deviation from the normal distribution caused both by its skewness and flattening. The performed experiments concerned analyses of the distribution of sound levels: LD, LE, LN, LDWN, being the basic noise indicators in assessments of the environment acoustic hazards.

Картофелекопатель с ротационной сепарирующей поверхностью

2018 ◽  
Author(s):  
V.M. Alakin ◽  
G.S. Nikitin
Keyword(s):  
Performance Data ◽  
Pilot Studies ◽  
Research Results ◽  
Operating Modes ◽  
Analysis Of Results ◽  
Design Characteristics ◽  
And Performance ◽  
Definition Of

Приведены результаты исследований экспериментального картофелекопателя с ротационной сепарирующей поверхностью. Особое внимание уделяется обоснованию конструктивных параметров и определению рабочих характеристик нового сепарирующего устройства. На основе анализа результатов экспериментальных исследований определены наиболее оптимальные режимы работы экспериментального картофелекопателя.Research results of an experimental potato digger with rotational separating web are published in this article. Special attention is paid to definition of design characteristics and performance data of the new separating device. Admissible operating modes are defined on the basis of the analysis of results of pilot studies of the experimental potato digger.

Sign in / Sign up

Export Citation Format

Share Document