Chemicothermal treatment of races of universal joint bearings

1995 ◽  
Vol 37 (3) ◽  
pp. 119-121
Author(s):  
L. I. Volkova ◽  
F. A. Palei
Keyword(s):  
Chemicothermal Treatment ◽  
Universal Joint

No more rattling: biomechanical evaluation of a hexapod ring fixator free of play

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Markus Greinwald ◽  
Emily K. Bliven ◽  
Alex Trompeter ◽  
Peter Augat
Keyword(s):  
Mechanical Performance ◽  
Steel Frame ◽  
Ball Joint ◽  
Universal Joint ◽  
Ring Fixator ◽  
Low Weight ◽  
Biomechanical Evaluation ◽  
Axial Fracture ◽  
Ball Joints ◽  
Universal Joints

Abstract Hexapod-ring-fixators have a characteristic rattling sound during load changes due to play in the hexapod struts. This play is perceived as unpleasant by patients and can lead to frame instability. Using slotted-ball-instead of universal-joints for the ring-strut connection could potentially resolve this problem. The purpose of the study was to clarify if the use of slotted-ball-joints reduces play and also fracture gap movement. A hexapod-fixator with slotted-ball-joints and aluminum struts (Ball-Al) was compared to universal-joint-fixators with either aluminum (Uni Al) or steel struts (Uni Steel). Six fixator frames each were loaded in tension, compression, torsion, bending and shear and mechanical performance was analyzed in terms of movement, stiffness and play. The slotted-ball-joint fixator was the only system without measurable axial play (<0.01 mm) compared to Uni-Al (1.2 ± 0.1) mm and Uni-Steel (0.6 ± 0.2) mm (p≤0.001). In both shear directions the Uni-Al had the largest play (p≤0.014). The resulting axial fracture gap movements were similar for the two aluminum frames and up to 25% smaller for the steel frame, mainly due to the highest stiffness found for the Uni-Steel in all loading scenarios (p≤0.036). However, the Uni-Steel construct was also up to 29% (450 g) heavier and had fewer usable mounting holes. In conclusion, the slotted-ball-joints of the Ball-Al fixator reduced play and minimized shear movement in the fracture while maintaining low weight of the construct. The heavier and stiffer Uni-Steel fixator compensates for existing play with a higher overall stiffness.

scholarly journals Spacer for Double Bundle in Phase Conductor of Transmission Line Based on Cross Universal Joint Structure

2021 ◽  
Vol 687 (1) ◽  
pp. 012117
Author(s):  
Ma Jun ◽  
Shi Yonggang ◽  
Dong Gang ◽  
Gong Fuxing ◽  
Wang Zhu ◽  
...  
Keyword(s):  
Transmission Line ◽  
Double Bundle ◽  
Universal Joint ◽  
Joint Structure

Errors in angle transfer with a universal joint

1981 ◽  
Vol 24 (11) ◽  
pp. 954-957
Author(s):  
B. N. Ivanov
Keyword(s):  
Universal Joint

Effect of conditions of complex chemicothermal treatment on residual stress distribution

1993 ◽  
Vol 28 (1) ◽  
pp. 98-100
Author(s):  
M. F. Berezhnitskaya ◽  
A. K. Tikhonov ◽  
N. V. Bogdanova
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Chemicothermal Treatment ◽  
Residual Stress Distribution

Residual stresses in alloys after chemicothermal treatment

1967 ◽  
Vol 9 (3) ◽  
pp. 165-168
Author(s):  
A. I. Efimov ◽  
S. T. Kishkin ◽  
V. V. Nikolenko ◽  
M. S. Khazanov
Keyword(s):  
Residual Stresses ◽  
Chemicothermal Treatment

Use of glow-discharge for chemicothermal treatment

1967 ◽  
Vol 9 (3) ◽  
pp. 162-164
Author(s):  
O. I. Butenko ◽  
Yu. N. Krymskii ◽  
Yu. M. Lakhtin
Keyword(s):  
Glow Discharge ◽  
Chemicothermal Treatment

Analysis and Synthesis of Mechanical Error in Universal Joints

1990 ◽  
Author(s):  
J. L. Cagney ◽  
S. S. Rao
Keyword(s):  
Probability Distribution ◽  
Real World ◽  
Probability Distributions ◽  
Manufacturing Cost ◽  
Universal Joint ◽  
Accuracy Requirement ◽  
Output Error ◽  
Manufacturing Errors ◽  
Analysis And Synthesis ◽  
Limiting Value

Abstract The modeling of manufacturing errors in mechanisms is a significant task to validate practical designs. The use of probability distributions for errors can simulate manufacturing variations and real world operations. This paper presents the mechanical error analysis of universal joint drivelines. Each error is simulated using a probability distribution, i.e., a design of the mechanism is created by assigning random values to the errors. Each design is then evaluated by comparing the output error with a limiting value and the reliability of the universal joint is estimated. For this, the design is considered a failure whenever the output error exceeds the specified limit. In addition, the problem of synthesis, which involves the allocation of tolerances (errors) for minimum manufacturing cost without violating a specified accuracy requirement of the output, is also considered. Three probability distributions — normal, Weibull and beta distributions — were used to simulate the random values of the errors. The similarity of the results given by the three distributions suggests that the use of normal distribution would be acceptable for modeling the tolerances in most cases.

scholarly journals Finite Element Methods based Structural Analysis of Universal Joint using Structural Steel Material

2017 ◽  
Vol 10 (31) ◽  
pp. 1-7
Author(s):  
Gagandeep Singh ◽  
Sandeep Singh ◽  
Rajbir Singh ◽  
◽  
◽  
...  
Keyword(s):  
Finite Element ◽  
Structural Analysis ◽  
Structural Steel ◽  
Finite Element Methods ◽  
Universal Joint ◽  
Steel Material

Assembly of composite shaft and yoke members of a Hookes universal joint

Composites ◽  
1988 ◽  
Vol 19 (4) ◽  
pp. 332
Keyword(s):  
Universal Joint ◽  
Composite Shaft
Sign in / Sign up

Export Citation Format

Share Document