Selective solid-phase extraction of tebuconazole in biological and environmental samples using molecularly imprinted polymers

2006 ◽  
Vol 387 (3) ◽  
pp. 1007-1016 ◽  
Author(s):  
Mai-ling Hu ◽  
Ming Jiang ◽  
Peng Wang ◽  
Su-rong Mei ◽  
Yan-fei Lin ◽  
...  
Keyword(s):  
Solid Phase Extraction ◽  
Molecularly Imprinted Polymers ◽  
Environmental Samples ◽  
Solid Phase ◽  
Phase Extraction ◽  
Molecularly Imprinted ◽  
Imprinted Polymers ◽  
Biological And Environmental Samples

Highly selective enrichment and direct determination of imazethapyr residues from milk using magnetic solid-phase extraction based on restricted-access molecularly imprinted polymers

2021 ◽  
Author(s):  
Shicong Jia ◽  
yanqiang zhou ◽  
Jianmin Li ◽  
Bolin Gong ◽  
Shujuan Ma ◽  
...  
Keyword(s):  
Solid Phase Extraction ◽  
Molecularly Imprinted Polymers ◽  
Solid Phase ◽  
Direct Determination ◽  
Magnetic Solid Phase Extraction ◽  
Phase Extraction ◽  
Molecularly Imprinted ◽  
Restricted Access ◽  
Imprinted Polymers ◽  
Magnetic Solid

The restricted access media magnetic molecularly imprinted polymers (RAM-MMIPs) were prepared as magnetic solid phase extraction (M-SPE) material by reversible addition fragmentation chain transfer (RAFT) technique. The resulting RAM-MMIPs had...

The Application of Molecularly Imprinted Polymers to Solid-Phase Extraction

2014 ◽  
Vol 893 ◽  
pp. 283-286
Author(s):  
Hong Ying Pei ◽  
Gui Jun Shen ◽  
Yu Du
Keyword(s):  
Solid Phase Extraction ◽  
Molecularly Imprinted Polymers ◽  
Biological Samples ◽  
Solid Phase ◽  
Phase Extraction ◽  
Molecularly Imprinted ◽  
Imprinted Polymers ◽  
Structural Analogues ◽  
Environmental And Biological Samples

A benefit of imprinted polymers is the possibility to prepare sorbents with selectivity pre-determined for a particular substance, or group of structural analogues. The application most close to a wider acceptance is probably that of solid phase extraction for clean-up of environmental and biological samples. The technique of molecularly imprinted polymers to solid phase extraction (MISPE) is performance and high selectively, compared with traditional sorbents. In this paper, the preparation and application of MIPs would be reviewed.

scholarly journals Development of Surface Molecularly Imprinted Polymers as Dispersive Solid Phase Extraction Coupled with HPLC Method for the Removal and Detection of Griseofulvin in Surface Water

2019 ◽  
Vol 17 (1) ◽  
pp. 134 ◽  
Author(s):  
Kamran Bashir ◽  
Zhimin Luo ◽  
Guoning Chen ◽  
Hua Shu ◽  
Xia Cui ◽  
...  
Keyword(s):  
Surface Water ◽  
Solid Phase Extraction ◽  
Molecularly Imprinted Polymers ◽  
Water Samples ◽  
Solid Phase ◽  
Phase Extraction ◽  
Dispersive Solid Phase Extraction ◽  
Molecularly Imprinted ◽  
Imprinted Polymers ◽  
Surface Water Samples

Griseofulvin (GSF) is clinically employed to treat fungal infections in humans and animals. GSF was detected in surface waters as a pharmaceutical pollutant. GSF detection as an anthropogenic pollutant is considered as a possible source of drug resistance and risk factor in ecosystem. To address this concern, a new extraction and enrichment method was developed. GSF-surface molecularly imprinted polymers (GSF-SMIPs) were prepared and applied as solid phase extraction (SPE) sorbent. A dispersive solid phase extraction (DSPE) method was designed and combined with HPLC for the analysis of GSF in surface water samples. The performance of GSF-SMIPs was assessed for its potential to remove GSF from water samples. The factors affecting the removal efficiency such as sample pH and ionic strength were investigated and optimized. The DSPE conditions such as the amount of GSF-SMIPs, the extraction time, the type and volume of desorption solvents were also optimized. The established method is linear over the range of 0.1–100 µg/mL. The limits of detection and quantification were 0.01 and 0.03 µg/mL respectively. Good recoveries (91.6–98.8%) were achieved after DSPE. The intra-day and inter-day relative standard deviations were 0.8 and 4.3% respectively. The SMIPs demonstrated good removal efficiency (91.6%) as compared to powder activated carbon (67.7%). Moreover, the SMIPs can be reused 10 times for water samples. This is an additional advantage over single-use activated carbon and other commercial sorbents. This study provides a specific and sensitive method for the selective extraction and detection of GSF in surface water samples.

Sign in / Sign up

Export Citation Format

Share Document