Formation of structure, phase composition and properties in biocompatible titanium alloy due to heat treatment

2011 ◽  
Vol 52 (9-10) ◽  
pp. 481-486 ◽  
Author(s):  
A. G. Illarionov ◽  
M. S. Karabanalov ◽  
S. I. Stepanov
Keyword(s):  
Heat Treatment ◽  
Titanium Alloy ◽  
Phase Composition ◽  
Structure Phase

Effect of heat treatment on the structure, phase composition, and mechanical properties of VN-10 alloy

1993 ◽  
Vol 29 (1) ◽  
pp. 56-60 ◽  
Author(s):  
O. I. Eliseeva ◽  
V. I. Kalyandruk ◽  
A. A. Denisova ◽  
V. V. Shirokov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Composition ◽  
Structure Phase

The Study of Ingots and Deformed Semi-Finished Products of Al-Mg-Sc and Al-Cu-Li Alloys Using Diffraction Methods

2016 ◽  
Vol 877 ◽  
pp. 471-476 ◽  
Author(s):  
Boris Ovsyannikov ◽  
Olga Chikova ◽  
Pavel Reznik
Keyword(s):  
Crystal Structure ◽  
Heat Treatment ◽  
Phase Composition ◽  
Structure Phase ◽  
The Difference ◽  
Annealing Mode

The influence of Al-Mg-Sc ingots and Al-Cu-Li semi-finished products heat treatment modes on structure, phase composition, and crystal structure was studied. Based on EBSD and EDS data, the difference of the sample microstructures was detected and the most favorable annealing mode for further deformation was presumed.

scholarly journals Structural and Phase Transformation in a Cold-Deformed Titanium Alloy During Aging

2019 ◽  
Vol 1 (1) ◽  
pp. 19
Author(s):  
A.G. Illarionov ◽  
I.V. Narygina ◽  
M.S. Karabanalov ◽  
I.A. Kylosova
Keyword(s):  
Titanium Alloy ◽  
Phase Transformation ◽  
Phase Composition ◽  
Structure Phase

The change of structure, phase composition and properties during aging of VT22(Ti-5Al-5Mo-5V-1Fe-1Cr) titanium alloy rods, pre-quenched from

Effect of sintering mode on structure, phase composition and porosity of titanium alloy VT6 parts made by injection molding method of powder-polymer compounds

2020 ◽  
pp. 2-13
Author(s):  
A.B. Semyonov ◽  
◽  
A.N. Muranov ◽  
A.A. Kutsbakh ◽  
D.M. Krotov ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Phase Composition ◽  
Injection Molding ◽  
Die Casting ◽  
Polymer Mixture ◽  
Casting Method ◽  
Molding Method ◽  
Structure Phase ◽  
Pressure Die Casting

Changes in the structure and the phase composition of a part made of powder of domestic titanium alloy VT6 produced at JSC «SMK», by the pressure die casting method of a powder-polymer mixture have been studied. The changes take place due to a change in the sintering mode of the porous semi-finished product.

Microstructure, Phase Composition, Physical and Mechanical Properties of Titanium Alloy VT23 Hot-Extruded Tube

2021 ◽  
Vol 410 ◽  
pp. 324-329
Author(s):  
Fedor V. Vodolazskiy ◽  
Anatoliy G. Illarionov ◽  
Natalya A. Shirinkina
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Phase Composition ◽  
Phase State ◽  
Physical And Mechanical Properties ◽  
Transmission Microscopy ◽  
X Ray ◽  
Structure Phase ◽  
Close Relationship ◽  
Alloy Vt23

Macro-, microstructural, fine structure, phase composition, texture and complex of physical and mechanical properties in titanium alloy VT23 (Ti-5.5Al-4.7V-2.5Mo-1.1Cr-0.7Fe, wt. %) tube were studded by the macroanalysis, optical and transmission microscopy, X-ray phase analysis, durometry and microindentation methods. A close relationship between the structural-textural-phase state formed during the extrusion and the obtained level of strength, plastic, durometric properties and the contact modulus of elasticity in a hot-extruded tube has been established.

Sign in / Sign up

Export Citation Format

Share Document