About Residual Stress State of Castings: The Case of HPDC Parts and Possible Advantages through Semi-Solid Processes

Nowadays, one of the most crucial focus in the aluminium-foundry sector is the production of high-quality castings. Mainly, High-Pressure Die Casting (HPDC) is broadly adopted, since by this process is possible to realize aluminium castings with thin walls and high specific mechanical properties. On the other hand, this casting process may cause tensile states into the castings, namely residual stresses. Residual stresses may strongly affect the life of the product causing premature failure of the casting. Various methods can assess these tensile states, but the non-destructive X-Ray method is the most commonly adopted. Namely, in this work, the residual stress analysis has been performed through Sinto-Pulstec μ-X360s. Detailed measurements have been done on powertrain components realized in aluminium alloy EN AC 46000 through HPDC processes to understand and prevent dangerous residual stress state into the aluminium castings. Furthermore, a comparison with stresses induced by Rheocasting processes is underway. In fact, it is well known that Semi-Solid metal forming combines the advantages of casting and forging, solving safety and environmental problems and possibly even the residual stress state can be positively affected.

Properties of Semisolid Parts: Comparison with Conventional and Innovative Manufacturing Technologies

In this paper, wear properties of samples manufactured using thixocasting were compared with those of components obtained using low-pressure die-casting and additive manufacturing in order to assess the relationship between material performance and production technologies, both conventional and innovative. The investigated items were made with AlSi7Mg alloy. First, microstructural analysis and hardness measurements were carried out. Subsequently, pin-on-disk wear tests were performed. Wear behavior of the samples was studied considering both coefficient of friction and wear rate, while the damage mechanism was analyzed by observation of the worn paths using scanning electron microscope, correlating the behavior to the specific microstructure. In addition, the effect of selected heat-treated conditions, relevant for real applications, on wear properties was also evaluated.

Biscuit Thickness Validation (HPDC)

Thank you very much; I am bharat sharma founder of steady die casting solutions. This time I have found one more solution for biscuit thickness validation in high pressure die casting. In this paper we will discuss, what is biscuit thickness?, why we need to identify right biscuit thickness?, how we can validate right biscuit thickness? and effect of biscuit thickness variation. This paper is all about to clear all myth to calculate biscuit thickness in high pressure die casting. This is very serious business when we are calculating biscuit thickness to avoid casting defect. Through this paper I would like to share this knowledge and I hope it will helpful to others. “Keep learning till death “. Keywords: (Biscuit thickness, plunger, hpdc, die casting, casting defect, solidification)

Metamodels’ Development for High Pressure Die Casting of Aluminum Alloy

Simulation is a very useful tool in the design of the part and process conditions of high-pressure die casting (HPDC), due to the intrinsic complexity of this manufacturing process. Usually, physics-based models solved by finite element or finite volume methods are used, but their main drawback is the long calculation time. In order to apply optimization strategies in the design process or to implement online predictive systems, faster models are required. One solution is the use of surrogate models, also called metamodels or grey-box models. The novelty of the work presented here lies in the development of several metamodels for the HPDC process. These metamodels are based on a gradient boosting regressor technique and derived from a physics-based finite element model. The results show that the developed metamodels are able to predict with high accuracy the secondary dendrite arm spacing (SDAS) of the cast parts and, with good accuracy, the misrun risk and the shrinkage level. Results obtained in the predictions of microporosity and macroporosity, eutectic percentage, and grain density were less accurate. The metamodels were very fast (less than 1 s); therefore, they can be used for optimization activities or be integrated into online prediction systems for the HPDC industry. The case study corresponds to several parts of aluminum cast alloys, used in the automotive industry, manufactured by high-pressure die casting in a multicavity mold.

Bonding of Cast Iron-Aluminum In Bimetallic Castings By High Pressure Die Casting Process

A practical bimetallic casting consisting of aluminum matrix and cast iron inserts was manufactured via high pressure die casting (HPDC) process. Different surface treatment methods of the cast iron inserts, including salt membrane plating and electrogalvanizing, were adopted to improve the bonding quality of bimetallic castings. Microstructure characterization on the bonding interface was conducted at different locations of bimetallic castings. Results indicate that compounds with flawless and continuously metallurgical bonding interface can be successfully fabricated by the HPDC process with the zinc rack plating treatment on the surface of cast iron inserts which results in a dense zinc coating with an average thickness of 8 μm. The melt flow speed and heat transition during solidification of the HPDC process are two key factors in determining the bonding integrity of bimetallic castings. With the dissolution and diffusion of the very thin zinc coating during solidification, there is no obvious aggregation of zinc element at the metallurgical bonding interface. Instead, a reaction layer with an irregular tongue-like morphology is formed with an average thickness of approximately 1 μm while it mainly consists of intermetallic phases Al60Cu30Fe10 and Al2FeSi, etc.