Modal parameters identification of a rotor-journal bearing system using operational modal analysis

2021 ◽  
Vol 43 (3) ◽  
Author(s):  
Gustavo Chaves Storti ◽  
Felipe Wenzel da Silva Tuckmantel ◽  
Tiago Henrique Machado
Keyword(s):  
Modal Analysis ◽  
Journal Bearing ◽  
Operational Modal Analysis ◽  
Parameters Identification ◽  
Modal Parameters ◽  
Modal Parameters Identification ◽  
Rotor Journal ◽  
Bearing System

Processing of Ambient Vibration Response for Modal Parameters Identification of a Jacket-Type Offshore Platform: Sea Test Study

2018 ◽  
Author(s):  
Xingxian Bao ◽  
Zhihui Liu ◽  
Chen Shi
Keyword(s):  
Noise Reduction ◽  
Modal Analysis ◽  
Measured Data ◽  
Offshore Platform ◽  
Operational Modal Analysis ◽  
Ambient Vibration ◽  
Data Matrix ◽  
Modal Parameters ◽  
Free Decay ◽  
Modal Parameters Identification

Modal parameters identification of offshore structures is important for many engineering applications, such as damage detection, structural health monitoring, etc. Operational modal analysis has been widely used for large structures. However, measured signals are inevitably contaminated with noise and may not be clean enough for identifying the modal parameters with proper accuracy. The traditional methods to estimate modal parameters in noisy situation are based on over-determined system to absorb the “noise modes” firstly, and then using the stability diagrams to distinguish the true modes from the “noise modes”. However, it is difficult to sort out true modes when the signal noise ratio is low, especially, the “noise modes” will also tend to be stable as the model order increases. This study develops a noise reduction procedure for polyreference complex exponential (PRCE) modal analysis based on ambient vibration responses. In the procedure, natural excitation technique (NExT) is firstly applied to get free decay responses (auto- and cross-correlation functions) from measured (noisy) ambient vibration data, and then the noise reduction method based on solving the partially described inverse singular value problem (PDISVP) is implemented to reconstruct a filtered data matrix from the measured data matrix. In our case, the measured data matrix is block Hankel structured, which is constructed based on the free decay responses. The filtered data matrix should maintain the block Hankel structure and be lowered in rank. When the filtered data matrix is obtained, the PRCE method is applied to estimate the modal parameters. The proposed NExT-PDISVP-PRCE scheme is applied to field test of a jacket type offshore platform. Results indicate that the proposed method can improve the accuracy of operational modal analysis.

scholarly journals Identification of modal parameters of machine tools during cutting by operational modal analysis

Procedia CIRP ◽  
2018 ◽  
Vol 77 ◽  
pp. 473-476 ◽  
Author(s):  
Jan Berthold ◽  
Martin Kolouch ◽  
Volker Wittstock ◽  
Matthias Putz
Keyword(s):  
Modal Analysis ◽  
Machine Tools ◽  
Operational Modal Analysis ◽  
Modal Parameters

EPCA basaed Modal Parameters Identification with Test data

2020 ◽  
Author(s):  
Jingjing Zhang ◽  
Xuan Zhang ◽  
Jinglin Luo ◽  
Mu Chai
Keyword(s):  
Test Data ◽  
Parameters Identification ◽  
Modal Parameters ◽  
Modal Parameters Identification

Evaluation of the effect of operational modal analysis algorithms on identified modal parameters of railway bridges

2021 ◽  
Author(s):  
Mohammadreza Salehi ◽  
Kultigin Demirlioglu ◽  
Emrah Erduran
Keyword(s):  
Modal Analysis ◽  
Health Monitoring ◽  
Iron Ore ◽  
Operational Modal Analysis ◽  
Modal Parameters ◽  
Vibration Source ◽  
Light Weight ◽  
Railway Bridges ◽  
Different Types ◽  
Vibration Responses

<p>The accuracy of modal parameters identified by Operational Modal Analysis (OMA) algorithms is of vital importance in vibration-based health monitoring. This paper reports the effects of using different OMA algorithms on identified modal parameters of railway bridges. For this purpose, comparison and application of three different OMA methods including FDD, ARX, SSI-COV are discussed. The vibration measurements are conducted on two railway bridges in Northern Norway for using five triaxial accelerometers. The first bridge is a single-span bridge with the length of 50 m, while the second is a two-span bridge with a total length of 85m. OMA has been conducted on the free vibration responses after passage of different types of trains including light-weight railway vehicles and heavily loaded iron ore trains to evaluate the variation of the identified modal parameters with the chosen algorithm and the vibration source on the OMA results.</p>

Signal Processing for Operational Modal Analysis of a Jacket-Type Offshore Platform: Sea Test Study

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Xingxian Bao ◽  
Zhihui Liu ◽  
Chen Shi
Keyword(s):  
Noise Reduction ◽  
Modal Analysis ◽  
Measured Data ◽  
Offshore Platform ◽  
Operational Modal Analysis ◽  
Ambient Vibration ◽  
Data Matrix ◽  
Modal Parameters ◽  
Stability Diagrams ◽  
Free Decay

Operational modal analysis (OMA) has been widely used for large structures. However, measured signals are inevitably contaminated with noise and may not be clean enough for identifying the modal parameters with proper accuracy. The traditional methods to estimate modal parameters in noisy situation are usually absorbing the “noise modes” first, and then using the stability diagrams to distinguish the true modes from the “noise modes.” However, it is still difficult to sort out true modes because the “noise modes” will also tend to be stable as the model order increases. This study develops a noise reduction procedure for polyreference complex exponential (PRCE) modal analysis based on ambient vibration responses. In the procedure, natural excitation technique (NExT) is first applied to get free decay responses from measured (noisy) ambient vibration data, and then the noise reduction method based on solving the partially described inverse singular value problem (PDISVP) is implemented to reconstruct a filtered data matrix from the measured data matrix. In our case, the measured data matrix is block Hankel structured, which is constructed based on the free decay responses. The filtered data matrix should maintain the block Hankel structure and be lowered in rank. When the filtered data matrix is obtained, the PRCE method is applied to estimate the modal parameters. The proposed NExT-PDISVP-PRCE scheme is applied to field test of a jacket type offshore platform. Results indicate that the proposed method can improve the accuracy of OMA.

Sign in / Sign up

Export Citation Format

Share Document