Experimental Investigation of the Mechanical Behavior of an AlSi-PE Abradable Coating at High Strain Rates for a Large Range of Temperatures

2020 ◽  
Vol 6 (2) ◽  
pp. 213-223
Author(s):  
S. Skiba ◽  
L. Faure ◽  
S. Philippon ◽  
J. Papasidero
Keyword(s):  
Experimental Investigation ◽  
Mechanical Behavior ◽  
Large Range ◽  
High Strain ◽  
Strain Rates ◽  
High Strain Rates ◽  
Abradable Coating

Experimental investigation on the compression behaviors of epoxy with carbon nanotube under high strain rates

2015 ◽  
Vol 69 ◽  
pp. 526-533 ◽  
Author(s):  
Pibo Ma ◽  
Gaoming Jiang ◽  
Qing Chen ◽  
Honglian Cong ◽  
Xiaolin Nie
Keyword(s):  
Experimental Investigation ◽  
Carbon Nanotube ◽  
High Strain ◽  
Strain Rates ◽  
High Strain Rates

Microstructural and Dynamic Mechanical Characterization of Biodegradable Magnesium-Calcium Alloy for Orthopedic Implants

2014 ◽  
Author(s):  
V. S. Brooks ◽  
Y. B. Guo
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Orthopedic Implants ◽  
Strain Rates ◽  
High Strain Rates ◽  
Static Compression ◽  
Metallic Biomaterial

Magnesium-Calcium (Mg-Ca) alloy is an emerging metallic biomaterial for manufacturing biodegradable orthopedic implants. However, very few studies have been conducted on mechanical properties of the bi-phase Mg-Ca alloy, especially at the high strain rates often encountered in manufacturing processes. The mechanical properties are critical to design and manufacturing of Mg-Ca implants. The objective of this study is to study the microstructural and mechanical properties of Mg-Ca0.8 (wt %) alloy. Both elastic and plastic behaviors of the Mg-Ca0.8 alloy were characterized at different strains and strain rates in quasi-static tension and compression testing as well as dynamic split-Hopkinson pressure bar (SHPB) testing. It has been shown that Young’s modulus of Mg-Ca0.8 alloy in quasi-static compression is much higher than those at high strain rates. Yield strength and ultimate strength of the material are very sensitive to strain rates and increase with strain rate in compression. Strain softening also occurs at large strains in dynamic compression. Furthermore, quasi-static mechanical behavior of the material in tension is very different from that in compression. The stress-strain data was repeatable with reasonable accuracy in both deformation modes. In addition, a set of material constants for the internal state variable plasticity model has been obtained to model the dynamical mechanical behavior of the novel metallic biomaterial.

Measurement of Young’s Modulus of Human Tympanic Membrane at High Strain Rates

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Huiyang Luo ◽  
Chenkai Dai ◽  
Rong Z. Gan ◽  
Hongbing Lu
Keyword(s):  
Mechanical Behavior ◽  
Tympanic Membrane ◽  
Young’S Modulus ◽  
High Strain ◽  
Young's Modulus ◽  
Strong Dependence ◽  
Strain Rates ◽  
Loading Conditions ◽  
High Strain Rates ◽  
Human Tympanic Membrane

The mechanical behavior of human tympanic membrane (TM) has been investigated extensively under quasistatic loading conditions in the past. The results, however, are sparse for the mechanical properties (e.g., Young's modulus) of the TM at high strain rates, which are critical input for modeling the mechanical response under blast wave. The property data at high strain rates can also potentially be converted into complex modulus in frequency domain to model acoustic transmission in the human ear. In this study, we developed a new miniature split Hopkinson tension bar to investigate the mechanical behavior of human TM at high strain rates so that a force of up to half of a newton can be measured accurately under dynamic loading conditions. Young’s modulus of a normal human TM is reported as 45.2–58.9 MPa in the radial direction, and 34.1–56.8 MPa in the circumferential direction at strain rates 300–2000 s−1. The results indicate that Young’s modulus has a strong dependence on strain rate at these high strain rates.

Nanocrystalline aluminum and iron: Mechanical behavior at quasi-static and high strain rates, and constitutive modeling

2006 ◽  
Vol 22 (2) ◽  
pp. 195-209 ◽  
Author(s):  
Akhtar S. Khan ◽  
Yeong S. Suh ◽  
Xu Chen ◽  
Laszlo Takacs ◽  
Haoyue Zhang
Keyword(s):  
Mechanical Behavior ◽  
Constitutive Modeling ◽  
High Strain ◽  
Strain Rates ◽  
High Strain Rates ◽  
Nanocrystalline Aluminum

The Mechanical Behavior of a Filled Elastomer at High Strain Rates

1969 ◽  
Vol 13 (3) ◽  
pp. 323-333 ◽  
Author(s):  
T. Nicholas ◽  
A. M. Freudenthal
Keyword(s):  
Mechanical Behavior ◽  
High Strain ◽  
Strain Rates ◽  
High Strain Rates ◽  
Filled Elastomer
Sign in / Sign up

Export Citation Format

Share Document