scholarly journals Experimental investigation of a latent heat thermal energy storage unit encapsulated with molten salt/metal foam composite seeded with nanoparticles

2021 ◽  
Author(s):  
Xin Xiao ◽  
Hongwei Jia ◽  
Dongsheng Wen ◽  
Yousef Golizadeh Akhkaghi ◽  
Ali Badiei
Keyword(s):  
Experimental Investigation ◽  
Energy Storage ◽  
Molten Salt ◽  
Latent Heat ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Metal Foam ◽  
Storage Unit ◽  
Energy Storage Unit ◽  
Foam Composite

scholarly journals Phase-Transition Thermal Charging of a Channel-Shape Thermal Energy Storage Unit: Taguchi Optimization Approach and Copper Foam Inserts

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1235
Author(s):  
Mohammad Ghalambaz ◽  
Seyed Abdollah Mansouri Mehryan ◽  
Ahmad Hajjar ◽  
Obai Younis ◽  
Mikhail A. Sheremet ◽  
...  
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Metal Foam ◽  
Volume Fraction ◽  
Foam Layer ◽  
Storage Unit ◽  
Energy Storage Unit ◽  
Copper Foam

Thermal energy storage is a technique that has the potential to contribute to future energy grids to reduce fluctuations in supply from renewable energy sources. The principle of energy storage is to drive an endothermic phase change when excess energy is available and to allow the phase change to reverse and release heat when energy demand exceeds supply. Unwanted charge leakage and low heat transfer rates can limit the effectiveness of the units, but both of these problems can be mitigated by incorporating a metal foam into the design of the storage unit. This study demonstrates the benefits of adding copper foam into a thermal energy storage unit based on capric acid enhanced by copper nanoparticles. The volume fraction of nanoparticles and the location and porosity of the foam were optimized using the Taguchi approach to minimize the charge leakage expected from simulations. Placing the foam layer at the bottom of the unit with the maximum possible height and minimum porosity led to the lowest charge time. The optimum concentration of nanoparticles was found to be 4 vol.%, while the maximu possible concentration was 6 vol.%. The use of an optimized design of the enclosure and the optimum fraction of nanoparticles led to a predicted charging time for the unit that was approximately 58% shorter than that of the worst design. A sensitivity analysis shows that the height of the foam layer and its porosity are the dominant variables, and the location of the porous layer and volume fraction of nanoparticles are of secondary importance. Therefore, a well-designed location and size of a metal foam layer could be used to improve the charging speed of thermal energy storage units significantly. In such designs, the porosity and the placement-location of the foam should be considered more strongly than other factors.

Numerical investigation of melting enhancement for paraffin in an innovative finned-plate latent heat thermal energy storage unit

2021 ◽  
Vol 43 ◽  
pp. 103222
Author(s):  
Hang Wang ◽  
Hai Xu ◽  
Changtian Liu ◽  
Zhen Zhang ◽  
Xiang Ling ◽  
...  
Keyword(s):  
Energy Storage ◽  
Numerical Investigation ◽  
Latent Heat ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage Unit ◽  
Energy Storage Unit

scholarly journals Design and operating evaluation of a finned shell-and-tube thermal energy storage unit filled with metal foam

2020 ◽  
Vol 261 ◽  
pp. 114385 ◽  
Author(s):  
Xiaohu Yang ◽  
Jiabang Yu ◽  
Tian Xiao ◽  
Zehuan Hu ◽  
Ya-Ling He
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Metal Foam ◽  
Storage Unit ◽  
Energy Storage Unit ◽  
Shell And Tube
Sign in / Sign up

Export Citation Format

Share Document