Measurement and correlation for two-phase frictional pressure drop characteristics of flow boiling in printed circuit heat exchangers

2021 ◽  
Author(s):  
Haitao Hu ◽  
Jianrui Li ◽  
Yongdong Chen ◽  
Yao Xie
Keyword(s):  
Pressure Drop ◽  
Heat Exchangers ◽  
Flow Boiling ◽  
Two Phase ◽  
Printed Circuit ◽  
Frictional Pressure Drop

A General Correlation for Frictional Pressure Drop of Flow Boiling in Plate Heat Exchangers

2020 ◽  
Author(s):  
Weiyu Tang ◽  
Tong Lv ◽  
Boren Zheng ◽  
Wei Li
Keyword(s):  
Pressure Drop ◽  
Heat Exchangers ◽  
Flow Boiling ◽  
Saturation Pressure ◽  
Influence Factors ◽  
Two Phase ◽  
Plate Heat ◽  
General Correlation ◽  
Frictional Pressure Drop ◽  
Data Points

Abstract Plate heat exchangers are widely used in various industries for many years. The corrugated channels on the plates effectively enhance the turbulence of flow boiling and complicate the prediction of pressure drop. This paper presents a brief review about the influence factors of frictional pressure drop during flow boiling in plate heat exchangers. Experimental data points of frictional pressure drop were collected from previous literatures to develop a general correlation. The database contained 454 data points, covering eight refrigerants, mass flux range 5.5–137 kg m-2 s-1, heat flux 0–30 kW m-2, vapor quality 0.07–0.95, saturation pressure 0.11–2.7 MPa, chevron angle 30°–70° and hydraulic diameter 1.7–5.4 mm. In this work, several existing correlations were compared with the database, and all of them seem fail to give an acceptable prediction. A new correlation was proposed with multiple regression analysis in terms of two-phase Fanning friction factor. The new method showed good agreement and predicted 63.2% and 92.9% of data points within ±30% and ±50% errors, respectively.

Analysis of Flow Boiling Frictional Pressure Drop in Plate Heat Exchangers

2020 ◽  
Vol 13 (3) ◽  
Author(s):  
Weiyu Tang ◽  
Tong Lv ◽  
Wei Li ◽  
S. A. Sherif ◽  
Zahid Ayub ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Heat Exchangers ◽  
Flow Boiling ◽  
Saturation Temperature ◽  
Two Phase ◽  
Plate Heat ◽  
Frictional Pressure Drop ◽  
Data Points ◽  
Geometrical Factors ◽  
Fanning Friction Factor

Abstract Plate heat exchangers are widely used in various industries for many years. The corrugated channels on the plates effectively enhance the turbulence of flow boiling and complicate the prediction of pressure drop. This article presents a brief review about effects of various operating and geometrical factors on frictional pressure drop during flow boiling in plate heat exchangers. Experimental data points of frictional pressure drop were collected from the previous literature to develop a general correlation. The database contained 591 data points, covering six different refrigerants, mass flux range 5.5–130 kg/m2/s1, heat flux 0–15 kW/m2, vapor quality 0.04–0.96, saturation temperature −25 to 61 C°, chevron angle 20 deg–65 deg, and hydraulic diameter 1.7–5.35 mm. In this study, several existing correlations were compared with the database, and most of them seem fail to give an acceptable prediction. A new correlation was proposed with multiple regression analysis in terms of two-phase Fanning friction factor. The new method showed a good agreement with the present database and predicted 70.2% and 91.7% of data points within ±30% and ±50% errors, respectively.

Flow boiling in horizontal flattened tubes: Part I – Two-phase frictional pressure drop results and model

2009 ◽  
Vol 52 (15-16) ◽  
pp. 3634-3644 ◽  
Author(s):  
Jesús Moreno Quibén ◽  
Lixin Cheng ◽  
Ricardo J. da Silva Lima ◽  
John R. Thome
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Two Phase ◽  
Frictional Pressure Drop

PRESSURE DROP CHARACTERISTICS OF R410A-OIL MIXTURE FLOW BOILING IN SMALL SMOOTH TUBES

2010 ◽  
Vol 18 (02) ◽  
pp. 109-116 ◽  
Author(s):  
YIFENG GAO ◽  
BIN DENG ◽  
GUOLIANG DING ◽  
HAITAO HU ◽  
XIANGCHAO HUANG
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Two Phase ◽  
Experimental Conditions ◽  
Mixture Flow ◽  
Frictional Pressure Drop ◽  
New Correlation ◽  
Smooth Tubes ◽  
Local Properties

This study presents experimental frictional pressure drop for R410A/oil mixture flow boiling in small horizontal smooth tubes with inside diameters of 4.18 mm and 2.0 mm. Experimental conditions cover nominal oil concentrations from 0 to 5%. The test results show that the presence of oil enhances two-phase frictional pressure drop about 0–120% and 0–90% at present test conditions for 4.18 mm I.D. smooth tube and 2.0 mm I.D. smooth tube, respectively, and the enhanced effect is more evident at higher vapor qualities where the local oil concentrations are higher. A new correlation to predict the local frictional pressure drop of R410A/oil mixture flow boiling inside conventional size and small smooth tubes is developed based on local properties of refrigerant–oil mixture, and the experimental data of 4.18 mm I.D. and 2.0 mm I.D. smooth tubes and that of 6.34 mm I.D. smooth tube (Hu et al., 2008) are well-correlated with the new correlation.

Experimental Investigation of Flow Boiling Pressure Drop of R134A in a Microscale Horizontal Smooth Tube

2011 ◽  
Vol 3 (1) ◽  
Author(s):  
Cristiano Bigonha Tibiriçá ◽  
Jaqueline Diniz da Silva ◽  
Gherhardt Ribatski
Keyword(s):  
Pressure Drop ◽  
High Speed ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Working Fluid ◽  
Prediction Methods ◽  
Internal Diameter ◽  
Two Phase ◽  
Pressure Drops ◽  
Frictional Pressure Drop

This paper presents new experimental flow boiling pressure drop results in a microscale tube. The experimental data were obtained under diabatic conditions in a horizontal smooth tube with an internal diameter of 2.32 mm. Experiments were performed with R134a as working fluid, mass velocities ranging from 100 kg/m2 s to 600 kg/m2 s, heat flux ranging from 10 kW/m2 to 55 kW/m2, saturation temperatures of 31°C, and exit vapor qualities from 0.20 to 0.99. Flow pattern characterization was also performed from images obtained by high-speed filming. Pressure drop gradients up to 48 kPa/m were measured. These data were carefully analyzed and compared against 13 two-phase frictional pressure drop prediction methods, including both macro- and microscale methods. Comparisons against these methods based on the data segregated according to flow patterns were also performed. Overall, the method by Cioncolini et al. (2009, “Unified Macro-to-Microscale Method to Predict Two-Phase Frictional Pressure Drops of Annular Flows,” Int. J. Multiphase Flow, 35, pp. 1138–1148) provided quite accurate predictions of the present database.

Sign in / Sign up

Export Citation Format

Share Document