Heat transfer performance assessment for forced convection in a tube partially filled with a porous medium

2012 ◽  
Vol 54 ◽  
pp. 98-108 ◽  
Author(s):  
Chen Yang ◽  
Akira Nakayama ◽  
Wei Liu
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Performance Assessment ◽  
Forced Convection ◽  
Heat Transfer Performance ◽  
Transfer Performance

Boiling/Evaporation Heat Transfer Augmentation Using Subchannels-Inserted Metal Porous Media

2013 ◽  
Author(s):  
Kazuhisa Yuki ◽  
Masahiro Uemura ◽  
Koichi Suzuki ◽  
Ken-ichi Sunamoto
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Electronic Devices ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Power Electronic ◽  
Copper Particles ◽  
Evaporation Heat

Two-phase flow loop system using a metal porous heat sink is proposed as a cooling system of the future power electronic devices with a heat load exceeding 300W/cm2. In this paper, as the first step, the heat transfer performance of the porous heat sink is evaluated under high heat flux conditions and the applicability and some engineering issues are discussed. The porous medium, which is fabricated by sintering copper particles, has a functional structure with several sub-channels inside it to enhance phase-change as well as discharge of generated vapor outside the porous medium. This porous heat sink is attached onto a heating chip and removes the heat by evaporating cooling liquid passing through the porous medium against the heat flow. Experiments using 30 kW of heating system show that the heat transfer performance of a copper-particles-sintered porous medium with the sub-channels exceeds 800W/cm2 in both high and low subcooling cases and achieves 300W/cm2 at a wall temperature of 150 °C (Tin = 70 °C) and 130 °C (Tin = 70 °C). These results prove that this porous heat sink is applicable enough for cooling 300 W/cm2 class of power electronic devices.

3D Printed Architected Heat Sinks Cooling Performance in Free and Forced Convection Environments

2020 ◽  
Author(s):  
Mohamed I. Hassan Ali ◽  
Oraib Al-Ketan ◽  
Mohamad Khalil ◽  
Nada Baobaid ◽  
Kamran Khan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Forced Convection ◽  
Heat Transfer Performance ◽  
Convection Heat Transfer ◽  
Heat Sinks ◽  
Cfd Modeling ◽  
Transfer Performance ◽  
Convection Heat ◽  
Performance Study

Abstract In this work, we extend our heat transfer performance study on our proposed new and novel 3D printable architected heat sinks with geometrically complex structures based on triply periodic minimal surfaces (TPMS). Computational fluid dynamics (CFD) modeling is used to assess the effect of porosity distribution, heat load, and isothermal boundary condition on the performance of the proposed TPMS-based heat sinks in active cooling using natural and forced convection heat transfer environments. The convection heat transfer coefficient, surface temperature, pressure drop are predicted using CFD method. The CFD model is validated using experimental results for the pressure drop and is verified by standard analytical results. Three TPMS structures are investigated in different orientations. Dimensionless heat transfer groups are developed to globalize the heat transfer performance of the proposed heat sinks.

scholarly journals Analytical Investigation into Effects of Capillary Force on Condensate Film Flowing over Horizontal Semicircular Tube in Porous Medium

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Tong-Bou Chang ◽  
Bai-Heng Shiue ◽  
Yi-Bin Ciou ◽  
Wai-Io Lo
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Capillary Force ◽  
Heat Transfer Performance ◽  
Capillary Forces ◽  
Gravity Force ◽  
Transfer Performance ◽  
Capillary Suction ◽  
Condensate Film ◽  
Energy Balance Approach

A theoretical investigation is performed into the problem of laminar filmwise condensation flow over a horizontal semicircular tube embedded in a porous medium and subject to capillary forces. The effects of the capillary force and gravity force on the condensation heat transfer performance are analyzed using an energy balance approach method. For analytical convenience, several dimensionless parameters are introduced, including the Jakob number Ja, Rayleigh number Ra, and capillary force parameter Boc. The resulting dimensionless governing equation is solved using the numerical shooting method to determine the effect of capillary forces on the condensate thickness. A capillary suction velocity can be obtained mathematically in the calculation process and indicates whether the gravity force is greater than the capillary force. It is shown that if the capillary force is greater than the condensate gravity force, the liquid condensate will be sucked into the two-phase zone. Under this condition, the condensate film thickness reduces and the heat transfer performance is correspondingly improved. Without considering the capillary force effects, the mean Nusselt number is also obtained in the present study as N u   ¯ | V 2 ∗ = 0 = 2 R a   D a / J a 1 / 2 ∫ 0 π 1 + cos   θ 1 / 2 d θ .

scholarly journals MHD Heat Transfer in W-Shaped Inclined Cavity Containing a Porous Medium Saturated with Ag/Al2O3 Hybrid Nanofluid in the Presence of Uniform Heat Generation/Absorption

Energies ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3457 ◽  
Author(s):  
Mohamed Dhia Massoudi ◽  
Mohamed Bechir Ben Hamida ◽  
Hussein A. Mohammed ◽  
Mohammed A. Almeshaal
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Aspect Ratio ◽  
Heat Generation ◽  
Heat Transfer Performance ◽  
Convection Heat Transfer ◽  
Hybrid Nanofluid ◽  
Transfer Performance ◽  
Convection Heat ◽  
Uniform Heat

In this paper, a 2D numerical study of natural convection heat transfer in a W-shaped inclined enclosure with a variable aspect ratio was performed. The enclosure contained a porous medium saturated with Ag/Al2O3 hybrid nanofluid in the presence of uniform heat generation or absorption under the effect of a uniform magnetic field. The vertical walls of the enclosure were heated differentially; however, the top and bottom walls were kept insulated. The governing equations were solved with numerical simulation software COMSOL Multiphysics which is based on the finite element method. The results showed that the convection heat transfer was improved with the increase of the aspect ratio; the average Nusselt number reached a maximum for an aspect ratio (AR) = 0.7 and the effect of the inclination was practically negligible for an aspect ratio of AR = 0.7. The maximum heat transfer performance was obtained for an inclination of ω = 15 and the minimum is obtained for ω = 30 . The addition of composite nanoparticles ameliorated the convection heat transfer performance. This effect was proportional to the increase of Rayleigh and Darcy numbers, the aspect ratio and the fraction of Ag in the volumetric fraction of nanoparticles.

Sign in / Sign up

Export Citation Format

Share Document