The reliability of muography applied in the detection of the animal burrows within River Levees validated by means of geophysical techniques

Gravity survey is one of the passive geophysical techniques commonly used to delineate geological formations, especially in determining basement rock and the overlying deposit. Geologically, the study area is made up of thick quaternary alluvium deposited on top of the older basement rock. The Muda River basin constitutes, approximately, of more than 300 m of thick quaternary alluvium overlying the unknown basement rock type. Previous studies, including drilling and geo-electrical resistivity surveys, were conducted in the area but none of them managed to conclusively determine the basement rock type and depth precisely. Hence, a regional gravity survey was conducted to determine the thickness of the quaternary sediments prior to assessing the sustainability of the Muda River basin. Gravity readings were made at 347 gravity stations spaced at 3–5 km intervals using Scintrex CG-3 covering an area and a perimeter of 9000 km2 and 730 km, respectively. The gravity data were then conventionally reduced for drift, free air, latitude, Bouguer, and terrain corrections. These data were then consequently analyzed to generate Bouguer, regional and total horizontal derivative (THD) anomaly maps for qualitative and quantitative interpretations. The Bouguer gravity anomaly map shows low gravity values in the north-eastern part of the study area interpreted as representing the Main Range granitic body, while relatively higher gravity values observed in the south-western part are interpreted as representing sedimentary rocks of Semanggol and Mahang formations. Patterns observed in the THD anomaly and Euler deconvolution maps closely resembled the presence of structural features such as fault lineaments dominantly trending along NW-SE and NE-SW like the trends of topographic lineaments in the study area. Based on power spectral analysis of the gravity data, the average depth of shallow body, representing alluvium, and deep body, representing underlying rock formations, are 0.5 km and 1.2 km, respectively. The thickness of Quaternary sediment and the depth of sedimentary formation can be more precisely estimated by other geophysical techniques such as the seismic reflection survey.

Download Full-text

Application of remote sensing, GIS and geophysical techniques for groundwater potential development in the crystalline basement complex of Ondo State, Southwestern Nigeria

Sustainable Water Resources Management ◽

10.1007/s40899-020-00486-5 ◽

2021 ◽

Vol 7 (1) ◽

Author(s):

Francis O. Akinluyi ◽

Martins O. Olorunfemi ◽

Oyelowo G. Bayowa

Keyword(s):

Remote Sensing ◽

Groundwater Potential ◽

Crystalline Basement ◽

Basement Complex ◽

Southwestern Nigeria ◽

Potential Development ◽

Geophysical Techniques ◽

Ondo State

Download Full-text

Example of Application of Geophysical Techniques in Determining Geological Environment of a Coal Deposit

Geological Society of America Bulletin ◽

10.1130/0016-7606(1973)84<2435:eoaogt>2.0.co;2 ◽

1973 ◽

Vol 84 (7) ◽

pp. 2435 ◽

Cited By ~ 3

Author(s):

ABUL FARAH

Keyword(s):

Geological Environment ◽

Coal Deposit ◽

Geophysical Techniques

Download Full-text

Application of geophysical methods for the investigation of the large gravitational mass movement of Séchilienne, France

Canadian Geotechnical Journal ◽

10.1139/t05-034 ◽

2005 ◽

Vol 42 (4) ◽

pp. 1105-1115 ◽

Cited By ~ 66

Author(s):

O Meric ◽

S Garambois ◽

D Jongmans ◽

M Wathelet ◽

J L Chatelain ◽

...

Keyword(s):

Rock Mass ◽

Mass Movement ◽

Seismic Refraction ◽

Geophysical Methods ◽

Time Lapse ◽

Gravitational Mass ◽

Electrical Tomography ◽

Refraction Tomography ◽

Geophysical Surveys ◽

Geophysical Techniques

Several geophysical techniques (electromagnetic profiling, electrical tomography, seismic refraction tomography, and spontaneous potential and seismic noise measurement) were applied in the investigation of the large gravitational mass movement of Séchilienne. France. The aim of this study was to test the ability of these methods to characterize and delineate the rock mass affected by this complex movement in mica schists, whose lateral and vertical limits are still uncertain. A major observation of this study is that all the zones strongly deformed (previously and at present) by the movement are characterized by high electrical resistivity values (>3 kΩ·m), in contrast to the undisturbed mass, which exhibits resistivity values between a few hundred and 1 kΩ·m. As shown by the surface observations and the seismic results, this resistivity increase is due to a high degree of fracturing associated with the creation of air-filled voids inside the mass. Other geophysical techniques were tested along a horizontal transect through the movement, and an outstanding coherency appeared between the geophysical anomalies and the displacement rate curve. These preliminary results illustrate the benefits of combined geophysical techniques for characterizing the rock mass involved in the movement. Results also suggest that monitoring the evolution of the rock mass movement with time-lapse geophysical surveys could be beneficial.Key words: gravitational movement, geophysical methods, Séchilienne.

Download Full-text

The use of geophysical prospecting for imaging active faults in the Roer Graben, Belgium

Geophysics ◽

10.1190/1.1444925 ◽

2001 ◽

Vol 66 (1) ◽

pp. 78-89 ◽

Cited By ~ 62

Author(s):

Donat Demanet ◽

François Renardy ◽

Kris Vanneste ◽

Denis Jongmans ◽

Thierry Camelbeeck ◽

...

Keyword(s):

High Resolution ◽

Physical Properties ◽

Fault Zone ◽

Geophysical Methods ◽

Depth Range ◽

Electrical Tomography ◽

Reflection Seismic ◽

Refraction Seismic ◽

Geophysical Surveys ◽

Geophysical Techniques

As part of a paleoseismological investigation along the Bree fault scarp (western border of the Roer Graben), various geophysical methods [electrical profiling, electromagnetic (EM) profiling, refraction seismic tests, electrical tomography, ground‐penetrating radar (GPR), and high‐resolution reflection seismic profiles] were used to locate and image an active fault zone in a depth range between a few decimeters to a few tens of meters. These geophysical investigations, in parallel with geomorphological and geological analyses, helped in the decision to locate trench excavations exposing the fault surfaces. The results could then be checked with the observations in four trenches excavated across the scarp. Geophysical methods pointed out anomalies at all sites of the fault position. The contrast of physical properties (electrical resistivity and permittivity, seismic velocity) observed between the two fault blocks is a result of a differences in the lithology of the juxtaposed soil layers and of a change in the water table depth across the fault. Extremely fast techniques like electrical and EM profiling or seismic refraction profiles localized the fault position within an accuracy of a few meters. In a second step, more detailed methods (electrical tomography and GPR) more precisely imaged the fault zone and revealed some structures that were observed in the trenches. Finally, one high‐resolution reflection seismic profile imaged the displacement of the fault at depths as large as 120 m and filled the gap between classical seismic reflection profiles and the shallow geophysical techniques. Like all geophysical surveys, the quality of the data is strongly dependent on the geologic environment and on the contrast of the physical properties between the juxtaposed formations. The combined use of various geophysical techniques is thus recommended for fault mapping, particularly for a preliminary investigation when the geological context is poorly defined.

Download Full-text