Influence of recycled concrete aggregates on alkali-activated slag mortar exposed to elevated temperatures

2019 ◽  
Vol 26 ◽  
pp. 100871 ◽  
Author(s):  
Arash Sedaghatdoost ◽  
Kiachehr Behfarnia ◽  
Mohammad Bayati ◽  
Mohammad sadegh Vaezi
2021 ◽  
Vol 13 (14) ◽  
pp. 8017
Author(s):  
Hilal El-Hassan ◽  
Jamal Medljy ◽  
Tamer El-Maaddawy

Reutilizing industrial by-products and recycled concrete aggregates (RCA) to replace cement and natural aggregates (NA) in concrete is becoming increasingly important for sustainable development. Yet, experimental evidence is needed prior to the widespread use of this sustainable concrete by the construction industry. This study examines the performance of alkali-activated slag concrete made with RCA and reinforced with steel fibers. Natural coarse aggregates were replaced with RCA. Steel fibers were added to mixes incorporating RCA at different volume fractions. Desert dune sand was used as fine aggregate. The mechanical and durability properties of plain and steel fiber-reinforced concrete made with RCA were experimentally examined. The results showed that the compressive strength did not decrease in plain concrete mixes with 30 and 70% RCA replacement. However, full replacement of NA with RCA resulted in a 20% reduction in the compressive strength of the plain mix. In fact, 100% RCA mixes could only be produced with compressive strength comparable to that of an NA-based control mix in conjunction with 2% steel fiber, by volume. In turn, at least 1% steel fiber, by volume, was required to maintain comparable splitting tensile strength. Furthermore, RCA replacement led to higher water absorption and sorptivity and lower bulk resistivity, ultrasonic pulse velocity, and abrasion resistance. Steel fiber incorporation in RCA-based mixes densified the concrete and improved its resistance to abrasion, water permeation, and transport, thereby enhancing its mechanical properties to exceed that of the NA-based counterpart. The hardened properties were correlated to 28-day cylinder compressive strength through analytical regression models.


Buildings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 327
Author(s):  
Hilal El-Hassan ◽  
Abdalla Hussein ◽  
Jamal Medljy ◽  
Tamer El-Maaddawy

This study evaluates the performance of alkali-activated slag-fly ash blended concrete made with recycled concrete aggregates (RCA) and reinforced with steel fibers. Two blends of concrete with ground granulated blast furnace slag-to-fly ash ratios of 3:1 and 1:1 were used. Natural aggregates were substituted with RCA, while macro steel fibers with 35 mm of length and aspect ratio of 65 were incorporated in RCA-based mixtures at various volume fractions. Fine aggregates were in the form of desert dune sand. Mechanical and durability characteristics were investigated. Experimental results revealed that RCA replacement decreased the compressive strength of plain concrete mixtures with more pronounced reductions being perceived at higher replacement percentages. Mixtures made with 30%, 70%, and 100% RCA could be produced with limited loss in the design compressive strength upon incorporating 1%, 2%, and 2% steel fibers, by volume, respectively. In turn, splitting tensile strength was comparable to the NA-based control while adding at least 1% steel fiber, by volume. Moreover, higher water absorption and capillary sorptivity and lower ultrasonic pulse velocity, bulk resistivity, and abrasion resistance were reported during RCA replacement. Meanwhile, incorporation of steel fibers densified the concrete and enhanced its resistance to abrasive forces, water permeation, and water transport. Analytical regression models were developed to correlate hardened concrete properties to the 28-day cylinder compressive strength.


2021 ◽  
pp. 103235
Author(s):  
Bruno Fernandes ◽  
Hélène Carré ◽  
Jean-Christophe Mindeguia ◽  
Céline Perlot ◽  
Christian La Borderie

2018 ◽  
Vol 276 ◽  
pp. 15-20 ◽  
Author(s):  
Pavel Rovnaník ◽  
Maria Míková ◽  
Ivo Kusák ◽  
Patrik Bayer

Alkali-activated slag is known as a building material for more than sixty years and is considered an alternative to Portland cement based binders. Compared to Portland cement it exhibits some superior properties such as higher resistance against chemical attack and exposure to elevated temperatures. Aluminosilicate binders are generally electrical insulators; however, electrical properties of building materials gain the importance in the new field of applications such as self-sensing or self-heating materials. This paper brings a comparison of the electrical properties, especially resistance and capacitance, between Portland cement and alkali-activated slag mortars. The measurements revealed that alkali-activated slag shows enhanced conducting properties due to the presence of mobile hydrated sodium ions and metallic iron microparticles.


Sign in / Sign up

Export Citation Format

Share Document