Solution of the diffraction problem on bodies of revolution with complex geometry using the method of continued boundary conditions

Author(s):  
Alexander G. Kyurkchan ◽  
Sergey A. Manenkov ◽  
Nadezhda I. Smirnova
2001 ◽  
Vol 15 (09) ◽  
pp. 1287-1303 ◽  
Author(s):  
HAI-PING FANG ◽  
LE-WEN FAN ◽  
ZUO-WEI WANG ◽  
ZHI-FANG LIN ◽  
YUE-HONG QIAN

The multicomponent nonideal gas lattice Boltzmann model by Shan and Chen (S-C) is used to study the immiscible displacement in a sinusoidal tube. The movement of interface and the contact point (contact line in three-dimension) is studied. Due to the roughness of the boundary, the contact point shows "stick-slip" mechanics. The "stick-slip" effect decreases as the speed of the interface increases. For fluids that are non-wetting, the interface is almost perpendicular to the boundaries at most time, although its shapes at different position of the tube are rather different. When the tube becomes narrow, the interface turns a complex curves rather than remains simple menisci. The velocity is found to vary considerably between the neighbor nodes close to the contact point, consistent with the experimental observation that the velocity is multi-values on the contact line. Finally, the effect of three boundary conditions is discussed. The average speed is found different for different boundary conditions. The simple bounce-back rule makes the contact point move fastest. Both the simple bounce-back and the no-slip bounce-back rules are more sensitive to the roughness of the boundary in comparison with the half-way bounce-back rule. The simulation results suggest that the S-C model may be a promising tool in simulating the displacement behaviour of two immiscible fluids in complex geometry.


2021 ◽  
Author(s):  
K. BUKENYA ◽  
M. N. OLAYA ◽  
E. J. PINEDA ◽  
M. MAIARU

Woven polymer matrix composites (PMCs) are leveraged in aerospace applications for their desirable specific properties, yet they are vulnerable to high residual stresses during manufacturing and their complex geometry makes experimental results difficult to observe. Process modeling is needed to characterize the effects of the curing and predict end stress states. Finite element software can be used to model woven architectures, however accurate representation of processing conditions remains a challenge when it comes to selecting boundary conditions. The effect of BCs on process-induced stress within woven PMCs is studied. The commercial Finite Element Analysis (FEA) software Abaqus is coupled with user-written subroutines in a process modeling framework. A two-dimensionally (2D) woven PMC repeating unit cell (RUC) is modeled with TexGen and Abaqus. Virtual curing is imposed on the bulk matrix. The BC study is conducted with Free, Periodic, Flat, and Flat-Free configurations. Results show that the end stress state is sensitive to the boundary condition assumptions. Flat BC results show great agreement with Periodic BCs. Residual stress results from process modeling are then compared with a linear-elastic thermal cooldown analysis in Abaqus. Cooldown results indicate an overestimation in matrix stresses compared with process modeling.


2013 ◽  
Vol 845 ◽  
pp. 71-75 ◽  
Author(s):  
Azma Putra ◽  
Nurain Shyafina ◽  
Noryani Muhammad ◽  
Hairul Bakri ◽  
Noor Fariza Saari

Simple analytical model of plate dynamics usually applies for rectangular plate with simply supported edges. Analytical model of sound radiation from rectangular plate is also convenient, but not for other geometries and other boundary conditions. This paper presents a hybrid mathematical model which combines a semi-analytical model with the Finite Element Analysis (FEA) method to determine sound radiation from a vibrating structure. The latter is employed to calculate the vibration velocity of a structure with a rather complex geometry. The results are then used as the input in the semi-analytical model to calculate the radiated sound pressure through the Rayleigh integral. Results from the proposed model are presented here for the radiation efficiency of rectangular plates with different boundary conditions.


1978 ◽  
Vol 22 (04) ◽  
pp. 216-230
Author(s):  
Kwang June Bai

A numerical method is presented for solving two-dimensional uniform flow problems with a linearized free-surface boundary condition. The boundary-value problem governed by Laplace's equation is replaced by a weak formulation (also known as Galerkin's method) with certain essential boundary conditions. The infinite domain of the fluid is reduced to a finite domain by utilizing known solution spaces in certain subdomains. The bases for the trial and test functions are chosen from the same subspace of the polynomial function space in the reduced subdomain. The essential boundary conditions are properly taken into account by an unconventional choice of the basis for the trial functions, which is different from that for the test functions in other subdomains. This method is applied to two-dimensional steady flow past a submerged elliptic section, a hydrofoil at an arbitrary angle of attack, and a bump on the bottom. In each example the body boundary condition is satisfied exactly. Both subcritical and supercritical flows are treated. We present the numerical results of wave resistance, lift force, moment, circulation strength, and flow blockage parameter. The computed pressure distributions on the hydrofoil and wave profiles are shown. The test results obtained by the present method agree very well with existing results. The main advantage of this method is that any complex geometry of the boundary can be easily accommodated.


Author(s):  
A. Houmat ◽  
J. R. Hutchinson

Abstract A boundary collocation method is presented for solving the problem of free vibrations of isotropic, linearly elastic simply connected bodies of revolution of arbitrary shape and arbitrary boundary conditions. The problem is formulated in terms of a series of exact solutions of the governing differential equations in spherical coordinates. Boundary conditions are satisfied at a discrete number of points on the boundary. Results are obtained for a number of simply connected bodies of revolution. For a solid sphere with stress free boundary, the results are compared with known solutions. For other shapes, the results are compared with finite element solutions obtained using ANSYS. All comparisons show that the boundary collocation method produces excellent results.


Sign in / Sign up

Export Citation Format

Share Document