scholarly journals Investigations on the effect of different influencing factors on film cooling effectiveness under the injection of synthetic coolant

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jianlong Chang ◽  
Xinlei Duan ◽  
Yang Du ◽  
Baoquan Guo ◽  
Yutian Pan
Keyword(s):  
Film Cooling ◽  
Elliptical Hole ◽  
Synthetic Jet ◽  
Cooling Effect ◽  
Flow Structures ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Cooling Method ◽  
Strong Controllability

AbstractBy combining the synthetic jet and film cooling, the incident cooling flow is specially treated to find a better film cooling method. Numerical simulations of the synthetic coolant ejected are carried out for analyzing the cooling performance in detail, under different blowing ratios, hole patterns, Strouhal numbers, and various orders of incidence for the two rows of holes. By comparing the flow structures and the cooling effect corresponding to the synthetic coolant and the steady coolant fields, it is found that within the scope of the investigations, the best cooling effect can be obtained under the incident conditions of an elliptical hole with the aspect ratio of 0.618, the blow molding ratio of 2.5, and the Strouhal number St = 0.22. Due to the strong controllability of the synthetic coolant, the synthetic coolant can be controlled through adjusting the frequency of blowing and suction, so as to change the interaction between vortex structures for improving film cooling effect in turn. As a result, the synthetic coolant ejection is more advisable in certain conditions to achieve better outcomes.

Implementation of Hole-Pair in Ramp to Improve Film Cooling Effectiveness on a Plain Surface

2020 ◽  
Author(s):  
Sadam Hussain ◽  
Xin Yan
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Density Ratio ◽  
Hole Pair ◽  
Cooling Effect ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cooling Hole ◽  
Plain Surface

Abstract Film cooling is one of the most critical technologies in modern gas turbine engine to protect the high temperature components from erosion. It allows gas turbines to operate above the thermal limits of blade materials by providing the protective cooling film layer on outer surfaces of blade against hot gases. To get a higher film cooling effect on plain surface, current study proposes a novel strategy with the implementation of hole-pair into ramp. To gain the film cooling effectiveness on the plain surface, RANS equations combined with k-ω turbulence model were solved with the commercial CFD solver ANSYS CFX11.0. In the numerical simulations, the density ratio (DR) is fixed at 1.6, and the film cooling effect on plain surface with different configurations (i.e. with only cooling hole, with only ramp, and with hole-pair in ramp) were numerically investigated at three blowing ratios M = 0.25, 0.5, and 0.75. The results show that the configuration with Hole-Pair in Ramp (HPR) upstream the cooling hole has a positive effect on film cooling enhancement on plain surface, especially along the spanwise direction. Compared with the baseline configuration, i.e. plain surface with cylindrical hole, the laterally-averaged film cooling effectiveness on plain surface with HPR is increased by 18%, while the laterally-averaged film cooling effectiveness on plain surface with only ramp is increased by 8% at M = 0.5. As the blowing ratio M increases from 0.25 to 0.75, the laterally-averaged film cooling effectiveness on plain surface with HPR is kept on increasing. At higher blowing ratio M = 0.75, film cooling effectiveness on plain surface with HPR is about 19% higher than the configuration with only ramp.

Effect of Unheated Starting Lengths on Film Cooling Experiments

2006 ◽  
Vol 128 (3) ◽  
pp. 579-588 ◽  
Author(s):  
Sarah M. Coulthard ◽  
Ralph J. Volino ◽  
Karen A. Flack
Keyword(s):  
Film Cooling ◽  
Infrared Camera ◽  
Stanton Number ◽  
Flow Structures ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Heat Transfer Coefficients ◽  
Film Cooling Holes

The effect of an unheated starting length upstream of a row of film cooling holes was studied experimentally to determine its effect on heat transfer coefficients downstream of the holes. Cases with a single row of cylindrical film cooling holes inclined at 35deg to the surface of a flat plate were considered at blowing ratios of 0.25, 0.5, 1.0, and 1.5. For each case, experiments were conducted to determine the film-cooling effectiveness and the Stanton number distributions in cases with the surface upstream of the holes heated and unheated. Measurements were made using an infrared camera, thermocouples, and hot and cold-wire anemometry. Ratios were computed of the Stanton number with film cooling (Stf) to corresponding Stanton numbers in cases without film cooling (Sto), but the same surface heating conditions. Contours of these ratios were qualitatively the same regardless of the upstream heating conditions, but the ratios were larger for the cases with a heating starting length. Differences were most pronounced just downstream of the holes and for the lower blowing rate cases. Even 12 diameters downstream of the holes, the Stanton number ratios were 10–15% higher with a heated starting length. At higher blowing rates the differences between the heated and unheated starting length cases were not significant. The differences in Stanton number distributions are related to jet flow structures, which vary with blowing rate.

Flow Dynamics and Film Cooling Effectiveness on a Non-Axisymmetric Contour Endwall in a Two-Dimensional Cascade Passage

2009 ◽  
Author(s):  
Gazi I. Mahmood ◽  
Ross Gustafson ◽  
Sumanta Acharya
Keyword(s):  
Temperature Field ◽  
Flow Field ◽  
Film Cooling ◽  
Free Stream ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Blowing Ratio

The measured flow field and temperature field near a three-dimensional asymmetric contour endwall employed in a linear blade cascade are presented with and without film-cooling flow on the endwall. Flow field temperature and Nusselt number distributions along the asymmetric endwall with wall heating and no film-cooling flow are also reported to show local high heat transfer region on the endwall and justify the locations of the coolant holes. Adiabatic film-cooling effectiveness along the endwall is then measured to indicate the local effects of the coolant jets. The near endwall flow field and temperature field provide the coolant flow behavior and the interaction of coolant jets with the boundary layer flow. Thus, the local film-cooling effectiveness can be explained with the coolant jet trajectories. The measurements are obtained at the Reynolds number of 2.30×105 based on blade actual chord and inlet velocity, coolant-to-free stream temperature ratio of 0.93, and coolant-to-free stream density ratio of 1.06. The cascade employs the hub side blade section and passage geometry of the first stage rotor of GE-E3 turbine engine. The contour endwall profile is employed on the bottom endwall only in the cascade. The blowing ratio of the film-cooling flow varies from 1.0 to 2.4 from 71 discrete cylindrical holes located in the contour endwall. The three-dimensional profile of the endwall varies in height in both the pitchwise and axial directions. The flow field is quantified with the streamwise vorticity and turbulent intensity, pitchwise static pressure difference, flow yaw angle, and pitchwise velocity. Both the flow field and temperature data indicate that the coolant jets cover more distance in the pitchwise and axial direction in the passage as the blowing ratio increases. Thus, the local and average film-cooling effectiveness increase with the blowing ratio.

A Numerical Investigation on the Performance of Novel Sister Shaped Single-Hole Configurations for Film Cooling Flow

2014 ◽  
Author(s):  
Siavash Khajehhasani ◽  
Bassam A. Jubran
Keyword(s):  
Film Cooling ◽  
The Novel ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Blowing Ratio ◽  
Single Hole ◽  
Attached Flow ◽  
Shaped Hole ◽  
Lift Off

The film cooling performance using novel sister shaped single-hole (SSSH) schemes are numerically investigated in the present study. The downstream, upstream and up/downstream SSSH configurations are formed by merging the discrete sister holes to the primary injection hole through a series of specific orientations. The obtained results are compared with a conventional cylindrical hole and a forward diffused shaped hole. The RANS simulations are performed using the realizable k-ε model with the standard wall function. Results are presented for low and high blowing ratios of 0.25 and 1.5, respectively. The film cooling effectiveness is notably increased for the novel shaped holes, particularly at the high blowing ratio of 1.5. Furthermore, a considerable decrease in the jet lift-off has been achieved for the proposed film hole geometries, wherein fully attached flow to the wall surface is observed for the upstream and up/downstream SSSH schemes.

Improvements of the Adiabatic Film Cooling by Using Two-Row Holes of Different Geometries and Arrangements

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Guohua Zhang ◽  
Jian Liu ◽  
Bengt Sundén ◽  
Gongnan Xie
Keyword(s):  
Film Cooling ◽  
Discharge Coefficient ◽  
Three Dimensional ◽  
Elliptical Hole ◽  
Cylindrical Hole ◽  
Maximum Deviation ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Elliptical Holes

Abstract Existing researches on two-row film cooling mainly focused on double-jet film cooling. However, researches on the effects by combining different kinds of hole shapes on film cooling performance are quite limited. In order to improve the film cooling effectiveness, the three-dimensional numerical method is utilized to investigate the effects of a novel structure composed of two-row holes with different shapes and arrangements on the adiabatic film cooling effectiveness with the blowing ratio of M = 1.5. To achieve this purpose, 30 different cases with two-row holes are designed and their film cooling effectiveness are compared with those of other seven cases with a single hole. Cases with two-row holes are designed by setting cylindrical, elliptical, or super-elliptical holes as the first-row, and arranging cylindrical holes with 30 deg, 45 deg, 60 deg, and 90 deg compound angles as the second row. The realizable k–ɛ turbulence model with enhanced wall function is utilized for all cases under identical boundary conditions. Similar film cooling performances are observed for cases with elliptical and super-elliptical holes being the first row, since the maximum deviation of film cooling effectiveness is less than 10%. It is found that the case integrates both a cylindrical hole and a cylindrical hole with 90 deg compound angle can greatly improve the film cooling performance with a higher discharge coefficient. However, the staggered case with an elliptical hole as both first- and second row gives the best film cooling effectiveness and the worst discharge coefficient due to the biggest resistance for the coolant flowing into the film hole.

Transonic Turbine Vane Endwall Film Cooling Using PSP Measurement Technique

2019 ◽  
Author(s):  
Chao-Cheng Shiau ◽  
Izzet Sahin ◽  
Izhar Ullah ◽  
Je-Chin Han ◽  
Alexander V. Mirzamoghadam ◽  
...  
Keyword(s):  
Shock Wave ◽  
Film Cooling ◽  
Density Ratio ◽  
Cross Flow ◽  
Flow Conditions ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Turbine Vane ◽  
Endwall Film Cooling

Abstract This work focuses on the parametric study of film cooling effectiveness on turbine vane endwall under various flow conditions. The experiments were performed in a five-vane annular sector cascade facility in a blowdown wind tunnel. The controlled exit isentropic Mach numbers were 0.7, 0.9, and 1.0, from high subsonic to transonic conditions. The freestream turbulence intensity is estimated to be 12%. Three coolant-to-mainstream mass flow ratios (MFR) in the range 0.75%, 1.0%, and 1.25% are studied. N2, CO2, and Argon/SF6 mixture were used to investigate the effects of density ratio (DR), ranging from 1.0, 1.5 to 2.0. There are 8 cylindrical holes on the endwall inside the passage. Pressure-sensitive paint (PSP) technique was used to capture the endwall pressure distribution for shock wave visualization and obtain the detailed film cooling effectiveness distributions. Both the high-fidelity effectiveness contour and the laterally (spanwise) averaged effectiveness were measured to quantify the parametric effect. This study will provide the gas turbine designer more insight on how the endwall film cooling effectiveness varies with different cooling flow conditions including shock wave through the endwall cross-flow passage.

Large Eddy Simulations on Fan Shaped Film Cooling Hole with Upstream Boundary Layer Turbulence Effect Generated by Trip Strip

2021 ◽  
pp. 1-37
Author(s):  
Young Seok Kang ◽  
Sangook Jun ◽  
Dong-Ho Rhee
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Film Cooling ◽  
Main Flow ◽  
Large Eddy Simulations ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Large Eddy ◽  
Cooling Hole

Abstract Large eddy simulations on the well-known 7-7-7 fan shaped cooling hole were carried out. Like using a trip strip to create turbulent boundary layer in practical experiments, trip strips with different configurations were placed upstream of the cooling hole to investigate incoming turbulent boundary layer effect on the film cooling flow behavior. Without the trip, horseshoe vortex generated by laminar boundary layer induced laterally discharging cooling flow in the lateral direction. Meanwhile, the induced cooling flow formed high film cooling effectiveness region around the film cooling hole. When the incoming boundary flow was turbulent, laterally discharged cooling flow was influenced by the turbulent boundary layer to dissipate to the main flow and resultant high effectiveness region disappeared. Depending on the trip configuration, quantitative characteristics of boundary layer such as turbulent intensity, momentum thickness and shape factor were strongly affected. Some trip configurations resulted in fully developed turbulent boundary layer just before leading edge of the film cooling hole. In such cases, distribution of the film cooling effectiveness showed a reasonable agreement with available experimental data where the quantitative properties of the turbulent boundary layer were similar. However, when the trip was located too close to the film cooling hole, the separated and reattached flow did not develop into the stabilized turbulent boundary layer. Then strong turbulence intensity in the main flow boundary layer stimulated break down of the cooling flow vortex structure and early dissipation to the main flow. It resulted in restricted film cooling flow coverage.

Large Eddy Simulations on Fan Shaped Film Cooling Hole With Various Inlet Turbulence Generation Methods

2020 ◽  
Author(s):  
Young Seok Kang ◽  
Sangook Jun ◽  
Dong-Ho Rhee
Keyword(s):  
Vortex Structure ◽  
Film Cooling ◽  
Main Flow ◽  
Large Eddy Simulations ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Large Eddy ◽  
Cooling Hole ◽  
Turbulence Generation

Abstract Large eddy simulations on well-known 7-7-7 fan shaped cooling hole have been carried out. Film cooling methods are generally applied to high pressure turbine, of which flow condition is extremely turbulent because high pressure turbines are generally located downstream combustor in gas turbines. However, different to RANS simulations, implementing turbulence at the main flow inlet is not simple in LES. For this reason, several numerical techniques have been devised to give turbulence information at the inlet boundary condition in LES. In this study, rectangular turbulator was located in front of the cooling hole to generate turbulent boundary flow in the main flow. Another method used in this study is transient table method to simulate turbulent flow at the main flow inlet. Without turbulent velocity components in approaching flow, laterally discharged cooling flow touches wall while it forms a vortex structure. Then high film cooling effectiveness region around the cooling hole appears. In the meanwhile, when approaching flow is turbulent, the laterally discharged cooling flow no more forms vortex structure and dissipated to the main flow and resultant high effectiveness region disappears. Both turbulence generation methods showed that turbulent intensity of the main flow affects effective range of the cooling flow and resultant film cooling effectiveness distributions. Also high turbulence intensity of the main flow stimulates early break down of the vortex structure coming out of the cooling hole and its dissipation to the main flow. It means high turbulent intensity restricts film cooling flow coverage. Another lesson from the study is that vortex generated from the cooling hole, its development and dissipation to the main flow, have an important role to understand film cooling effectiveness distributions around the cooling hole.

Sign in / Sign up

Export Citation Format

Share Document