Lignin isolation from spruce wood with low concentration aqueous alkali at high temperature and pressure: influence of hot-water pre-extraction

2015 ◽  
Vol 17 (11) ◽  
pp. 5058-5068 ◽  
Author(s):  
Ekaterina Korotkova ◽  
Andrey Pranovich ◽  
Johan Wärnå ◽  
Tapio Salmi ◽  
Dmitry Yu. Murzin ◽  
...  
Keyword(s):  
High Temperature ◽  
Hot Water ◽  
Aqueous Alkali ◽  
Low Concentration ◽  
Extraction Solvent ◽  
Spruce Wood ◽  
High Temperature And Pressure ◽  
Temperature And Pressure

Lignin was successfully isolated from spruce wood with an accelerated solvent extractor using low concentration aqueous NaOH as an extraction solvent. The biorefinery concept was also applied.

High Temperature and High Pressure ESP Performance Testing System Design

2013 ◽  
Vol 457-458 ◽  
pp. 423-427
Author(s):  
Xiao Qing Li ◽  
Xiao Yan Liu
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Heat Exchange ◽  
Liquid State ◽  
Constant Pressure ◽  
Hot Water ◽  
Testing System ◽  
Friction Resistance ◽  
High Temperature And Pressure ◽  
Temperature And Pressure

With the development of oilfield exploration, the performance of electric submersible pump (ESP) has been enhanced very fast. It requires testing techniques develop at the same time. The most outstanding question is the testing of high temperature and pressure ESP. A testing well was drilled in Daqing in 1992. It keeps the water liquid state on 150 centigrade by high pressure. This system can simulate operational mode 3000 meters under the ground. But many new ESPs have been produced these years. The quondam testing system couldnt meet the testing requirement. A new testing system is desiderated eagerly. This paper developed a high temperature and pressure ESP testing experimentation system. Hydraulic/thermodynamic analysis calculation has been carried on. Friction resistance from constant pressure point to the suction inlet of hot water pump and the ESP in heating-forced cycle and experimentation primary cycle are calculated respectively. Keeping the water liquid state on 180 centigrade, constant pressure value was fixed on 2.5 MPa. The heat load is calculated including the heat that the water in the system and the equipment need and the heat loss. In order to protect ESP from emanating too much heat to keep the temperature and pressure of the system steady, heat exchange system has been designed. Cold load and heat exchange square have been calculated. Friction resistance and the size of the cold water cistern have been calculated. These provide necessary academic foundation for the testing experimentation of high temperature and pressure ESP.

scholarly journals Fatigue simulation of a short fiber re-inforced oil-filter under high temperature and pressure load

2018 ◽  
Vol 213 ◽  
pp. 207-214 ◽  
Author(s):  
Michael Hack ◽  
Wolfgang Korte ◽  
Stefan Sträßer ◽  
Matthias Teschner
Keyword(s):  
High Temperature ◽  
Short Fiber ◽  
Pressure Load ◽  
High Temperature And Pressure ◽  
Temperature And Pressure

Creep Modeling of Welded Joints Using the Theta Projection Concept and Finite Element Analysis

1999 ◽  
Vol 122 (1) ◽  
pp. 22-26 ◽  
Author(s):  
M. Law ◽  
W. Payten ◽  
K. Snowden
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Temperature ◽  
Welded Joints ◽  
Creep Model ◽  
Projection Data ◽  
Predictive Capability ◽  
Element Analysis ◽  
High Temperature And Pressure ◽  
Temperature And Pressure

Modeling of welded joints under creep conditions with finite element analysis was undertaken using the theta projection method. The results were compared to modeling based on a simple Norton law. Theta projection data extends the accuracy and predictive capability of finite element modeling of critical structures operating at high temperature and pressure. In some cases analyzed, it was found that the results diverged from those gained using a Norton law creep model. [S0094-9930(00)00601-6]

High temperature and pressure rheological experiments on felsic granulite

2020 ◽  
Author(s):  
Dapeng Wen ◽  
Yongfeng Wang ◽  
Junfeng Zhang ◽  
Pengxiao Li ◽  
Zhen-Min Jin
Keyword(s):  
High Temperature ◽  
High Temperature And Pressure ◽  
Temperature And Pressure ◽  
Rheological Experiments

scholarly journals High temperature and pressure effects on the elastic properties of B2 intermetallics AgRE

Open Physics ◽  
2015 ◽  
Vol 13 (1) ◽  
Author(s):  
Lili Liu ◽  
Xiaozhi Wu ◽  
Weiguo Li ◽  
Rui Wang ◽  
Qing Liu
Keyword(s):  
High Temperature ◽  
Intermetallic Compounds ◽  
Elastic Properties ◽  
Elastic Constants ◽  
Second Order ◽  
Pressure Effects ◽  
High Temperature And Pressure ◽  
Normal Behavior ◽  
Temperature And Pressure ◽  
Temperature And Pressure Effects

AbstractThe high temperature and pressure effects on the elastic properties of the AgRE (RE=Sc, Tm, Er, Dy, Tb) intermetallic compounds with B2 structure have been performed from first principle calculations. For the temperature range 0-1000 K, the second order elastic constants for all the AgRE intermetallic compounds follow a normal behavior: they decrease with increasing temperature. The pressure dependence of the second order elastic constants has been investigated on the basis of the third order elastic constants. Temperature and pressure dependent elastic anisotropic parameters A have been calculated based on the temperature and pressure dependent elastic constants.

Exploring the Free Energy and Conformational Landscape of tRNA at High Temperature and Pressure

ChemPhysChem ◽  
2014 ◽  
Vol 16 (1) ◽  
pp. 138-146 ◽  
Author(s):  
Caroline Schuabb ◽  
Melanie Berghaus ◽  
Christopher Rosin ◽  
Roland Winter
Keyword(s):  
Free Energy ◽  
High Temperature ◽  
High Temperature And Pressure ◽  
Conformational Landscape ◽  
Temperature And Pressure
Sign in / Sign up

Export Citation Format

Share Document