Effect of Thermal Cycling on Martensitic Transformation Characteristics of (Ni47Ti44)100−xNbx Shape Memory Alloys

2006 ◽  
Author(s):  
X. M. He
Keyword(s):  
Martensitic Transformation ◽  
Shape Memory Alloys ◽  
Thermal Cycling ◽  
Shape Memory

scholarly journals Effect of Stoichiometry on Shape Memory Properties and Functional Stability of Ti–Ni–Pd Alloys

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 798 ◽  
Author(s):  
Yuki Hattori ◽  
Takahiro Taguchi ◽  
Hee Kim ◽  
Shuichi Miyazaki
Keyword(s):  
High Temperature ◽  
Martensitic Transformation ◽  
Shape Memory Alloys ◽  
Thermal Cycling ◽  
Shape Memory ◽  
Stoichiometric Composition ◽  
Atomic Ratio ◽  
Transformation Temperatures ◽  
Shape Memory Properties ◽  
Ti Content

Ti–Ni–Pd shape memory alloys are promising candidates for high-temperature actuators operating at above 373 K. One of the key issues in developing high-temperature shape memory alloys is the degradation of shape memory properties and dimensional stabilities because plastic deformation becomes more pronounced at higher working temperature ranges. In this study, the effect of the Ti:(Ni + Pd) atomic ratio in TixNi70−xPd30 alloys with Ti content in the range from 49 at.% to 52 at.% on the martensitic transformation temperatures, microstructures and shape memory properties during thermal cycling under constant stresses were investigated. The martensitic transformation temperatures decreased with increasing or decreasing Ti content from the stoichiometric composition. In both Ti-rich and Ti-lean alloys, the transformation temperatures decreased during thermal cycling and the degree of decrease in the transformation temperatures became more pronounced as the composition of the alloy departed from the stoichiometric composition. Ti2Pd and P phases were formed during thermal cycling in Ti-rich and Ti-lean alloys, respectively. Both Ti-rich and Ti-lean alloys exhibited superior dimensional stabilities and excellent shape memory properties with higher recovery ratio and larger work output during thermal cycling under constant stresses when compared with the alloys with near-stoichiometric composition.

Thermal cycling effects in high temperature Cu–Al–Ni–Mn–B shape memory alloys

1997 ◽  
Vol 12 (9) ◽  
pp. 2288-2297 ◽  
Author(s):  
J. Font ◽  
J. Muntasell ◽  
J. Pons ◽  
E. Cesari
Keyword(s):  
High Temperature ◽  
Martensitic Transformation ◽  
Shape Memory Alloys ◽  
Thermal Cycling ◽  
Shape Memory ◽  
Parent Phase ◽  
Aluminum Boride ◽  
Transformation Temperatures ◽  
Dsc Measurements ◽  
Number Of Cycles

The effects of thermal cycling through the martensitic transformation have been studied in three Cu–Al–Ni–Mn–B high temperature shape memory alloys. An increase of the martensitic transformation temperatures with the number of cycles (up to ∼7 K after 60 cycles) has been generally observed by DSC measurements. The microstructure of these alloys is rather complicated, with the presence of big manganese or aluminum boride particles and small boron precipitates, as well as the formation of dislocations during thermal cycling. By means of aging experiments, it has been shown that the evolution of transformation temperatures during cycling is mainly due to the step-by-step aging in parent phase accompanying the thermal cycling, and that the dislocations formed during cycling have only a very small effect, at least up to 60 cycles.

Atomic Order and Martensitic Transformation in Cu-Al-Be Shape Memory Alloys

1995 ◽  
Vol 05 (C8) ◽  
pp. C8-973-C8-978
Author(s):  
M. Jurado ◽  
Ll. Mañosa ◽  
A. González-Comas ◽  
C. Stassis ◽  
A. Planes
Keyword(s):  
Martensitic Transformation ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Atomic Order

scholarly journals Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys

2021 ◽  
Author(s):  
A. Bauer ◽  
M. Vollmer ◽  
T. Niendorf
Keyword(s):  
Martensitic Transformation ◽  
Grain Boundary ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Grain Boundaries ◽  
Tensile Tests ◽  
Image Correlation ◽  
Stress Concentrations ◽  
Grain Orientations ◽  
High Degree

AbstractIn situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is shown that grain boundaries lead to stress concentrations and, thus, to formation of unfavored martensite variants. Moreover, some martensite plates seem to penetrate the grain boundaries resulting in a high degree of irreversibility in this area. However, after a stable microstructural configuration is established in direct vicinity of the grain boundary, the transformation begins inside the neighboring grains eventually leading to a sequential transformation of all grains involved.

Sign in / Sign up

Export Citation Format

Share Document