Influence of meteorological parameters on the EM environment of UHVDC transmission line at high altitude

Author(s):  
Lei Liu ◽  
Min Li ◽  
Ruihai Li ◽  
Zhanqing Yu ◽  
Zhihong Liu ◽  
...  
2019 ◽  
Vol 2019 (16) ◽  
pp. 1185-1188
Author(s):  
Mou Ya ◽  
Zhanqing Yu ◽  
Min Li ◽  
Xiaorui Wang ◽  
Xi Yang ◽  
...  

2009 ◽  
Vol 16 (1) ◽  
pp. 88-98 ◽  
Author(s):  
Daochun Huang ◽  
Jiangjun Ruan ◽  
Wei Cai ◽  
Tianwei Li ◽  
Yuanhang Wei ◽  
...  

2018 ◽  
Vol 237 ◽  
pp. 01002
Author(s):  
XIA Yongjun ◽  
ZHAO Fei

The construction of transmission line in Tibet high altitude area has the characteristics of low pressure, low oxygen and low temperature. In the special environmental condition, the transmission line construction equipment with engine as the power source is highly effective, which affects the efficiency and safety of construction[1].The experimental study on engineering mechanical industry plateau transmission line is still in the blank stage,thus relying on the Tibet networking project selects 5 different high altitude test points to plateau 500kV transmission line construction commonly used types of pullers, tensioners and powered winch as an object of study to carry out the typical construction equipment energy efficiency test of field measurements effective output power equipment in different altitude environment from the perspective of practical application and analysis of law and effect mechanism of falling equipment.


2016 ◽  
Vol 16 (15) ◽  
pp. 9805-9830 ◽  
Author(s):  
A. E. Valsan ◽  
R. Ravikrishna ◽  
C. V. Biju ◽  
C. Pöhlker ◽  
V. R. Després ◽  
...  

Abstract. An ultraviolet aerodynamic particle sizer (UV-APS) was continuously operated for the first time during two seasons to sample the contrasting winds during monsoon and winter to characterize the properties of fluorescent biological aerosol particles (FBAPs), at a high-altitude site in India. Averaged over the entire monsoon campaign (1 June–21 August 2014), the arithmetic mean number and mass concentrations of coarse-mode (> 1 µm) FBAPs were 0.02 cm−3 and 0.24 µg m−3, respectively, which corresponded to  ∼  2 and 6 % of total aerosol loading, respectively. Average FBAP number size distribution exhibited a peak at  ∼  3 µm, which is attributed to the fungal spores, as supported by scanning electron microscope (SEM) images, and these results are consistent with previous studies made for FBAPs. During 11 weeks of measurements the variability of the total coarse-mode particle number (TAP) concentration was high compared to that observed in FBAP number concentrations. The TAP and FBAP number concentrations measured at this site were strongly dependent on changes in wind direction and rainfall. During periods of westerly/southwesterly winds with heavy persistent rainfall, the TAP and FBAP concentrations exhibited very low values (1.3 and 0.005 cm−3, respectively) with no significant diurnal variations, whereas during periods of northerly winds with scattered rainfall FBAPs exhibited relatively high concentration values (0.05 cm−3) with pronounced diurnal variations, which were strongly coupled with diurnal variations in meteorological parameters. The campaign-averaged FBAP number concentrations were shown to correlate with daily patterns of meteorological parameters and were positively correlated with relative humidity (RH; R2  =  0.58) and negatively with temperature (R2  =  0.60) and wind speed (R2  =  0.60). We did not observe any significant positive correlation with precipitation as reported by previous researchers from selected areas. These measurement results confirm the fact that the ratio of PBAPs to TAP is strongly dependent on particle size and location and thus may constitute a significant proportion of total aerosol particles.


2017 ◽  
Vol 863 ◽  
pp. 201-207 ◽  
Author(s):  
Xiang Yue ◽  
Hong Guang Wang ◽  
Yong Jiang

The working environment of the inspection robot is a high altitude flexible cable environment. The robot navigating process must be stable and reliable. The robot mechanism grips the line though locomotion mechanism when navigating obstacles. The locomotion mechanism needs to have a strong clamping capacity and stability. According to the environmental characteristics of transmission lines, a novel locomotion mechanism of inspection robot is presented. The locomotion mechanism adopting differential mechanism can grip different diameter lines. The Tri-Step reducer design to ensure that the various model lines of rapid firmly clamped. The locomotion mechanism is introduced, and the gripper force is analyzed. The experiment results demonstrate that the mechanism has such characteristics as strong grip ability, good motion stability, and different diameter lines gripping capability.


Sign in / Sign up

Export Citation Format

Share Document