EFFECT OF PIPERAZINE (PIP) CONCENTRATION AND REACTION TIME ON THE FORMATION OF THIN FILM COMPOSITE FORWARD OSMOSIS (FO) MEMBRANE

2017 ◽  
Vol 79 (1-2) ◽  
Author(s):  
Mohammad Amirul Mohd Yusof ◽  
Mazrul Nizam Abu Seman
Keyword(s):  
Thin Film ◽  
Reaction Time ◽  
Humic Acid ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Forward Osmosis ◽  
Angle Measurement ◽  
Film Composite ◽  
Thin Film Composite

Nowadays, wide applications of forward osmosis (FO) technology have been huge attention in solving the water shortage problems. Hence, the performance of thin film composite (TFC) forward osmosis membrane via interfacial polymerization (IP) was studied. 2% and 1% w/v of piperazine (PIP) and 0.15% w/v of trimesoyl chloride (TMC) were reacted with 3 different reaction time (60s, 30s, and 10s). The fabricated membranes were then characterized by FTIR, contact angle measurement and FESEM. Pure water flux, humic acid rejection (represent NOM) and salt leakage were evaluated to obtain the best polyamide FO membrane. The results demonstrated that polyamide FO membranes fabricated with 2% w/v possess a higher hydrophilic properties compared to 1% w/v. In addition, regardless of monomer concentrations, at longest reaction time (60s), there is no significant change in water flux. Membrane fabricated at 60s of reaction time exhibited water flux of 1.90 LMH and 1.92 LMH for 2% w/v and 1% w/v of PIP concentrations, respectively. The same trend also observed for humic acid rejection (93.9%-94.6%). The salt leakage test revealed that the minimum salt reverse diffusion (0.01-0.02 GMH) could be achieved for membrane fabricated at longest reaction time of 60s for both PIP concentrations. As conclusion, manipulating monomer concentrations and reaction time is the main key to obtain an optimal polyamide layer with high membrane performance covering higher water flux, higher removal of humic acid and lower reverse salt diffusion.  

scholarly journals Development of permeability properties of polyamide thin film composite nanofiltration membrane by using the dimethyl sulfoxide additive

2014 ◽  
Vol 4 (3) ◽  
pp. 174-181 ◽  
Author(s):  
Ahmad Akbari ◽  
Sayed Majid Mojallali Rostami
Keyword(s):  
Thin Film ◽  
Dimethyl Sulfoxide ◽  
Aqueous Phase ◽  
High Performance ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Film Composite ◽  
Chemical Structures ◽  
Thin Film Composite

A novel polyamide thin film composite (PATFC) as a nanofiltration (NF) membrane was prepared by a modified interfacial polymerization (IP) reaction. Herein trimesoyl chloride and piperazine as the reagents, dimethyl sulfoxide (DMSO) as additive and polysulfone (PSF) ultrafiltration membrane as support were used respectively. The main goal of the present study is to improve TFC membrane water flux by addition of DMSO into the aqueous phase of IP reaction, without considerable rejection loss. Morphological, roughness, and chemical structures of the PATFC membrane were analyzed by scanning electron microscopy, atomic force microscopy (AFM), and Fourier transform infrared spectroscopy (FT-IR), respectively. The AFM analysis demonstrated that as DMSO was added to the aqueous phase, the surface roughness of PATFC membrane increased. Results showed that the pure water flux of modified-PATFC membranes increased up to 46%, compared to nonmodified-PATFC membrane, while salt rejection was not sacrificed considerably. The results elucidated that the addition of DMSO leads to an increase in the number of cross-linking bonds between monomers and pore diameter, which results in enhancement of the membrane flux. Finally, the results showed that the newly developed PATFC membrane is a high-performance NF membrane which augments the efficiency of conventional PATFC membrane.

scholarly journals Synthesis And Performance Of Thin Film Composite Nanofiltration Polyester Membrane For Removal Of Natural Organic Matter Substances

2012 ◽  
Vol 12 (1) ◽  
pp. 73
Author(s):  
N.A. Jalanni ◽  
M.N. Abu Seman ◽  
C.K. M Faizal
Keyword(s):  
Thin Film ◽  
Reaction Time ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Process Efficiency ◽  
Transmembrane Pressure ◽  
Film Composite ◽  
Thin Film Composite ◽  
And Performance ◽  
Straight Lines

Nanofiltration (NF) polyester thin-film composite (TFC) membranes have been prepared by interfacial polymerization using commercial polyethersulfone membrane support. At 6% (w/v) triethanolamine (TEAO) concentrations in the aqueous solution and a range of interfacial polymerization times in the organic solution containing trimesoyl chloride (TMC) were studied. Nanofiltration membranes were produced with varying properties through interfacial polymerization technique. The ability to use NF membranes with varying properties will improve overall process efficiency. This study has shown that through interfacial polymerization technique, the variation of reaction time as well as can affect the performance of the membrane produced. As a result, increasing the reaction time resulted in decreasing water permeabilities. Polyester with some amide group produced after interfacial polymerization occurred as shown by FT-IR spectra. Straight lines were obtained between Jw and ΔP and the water flux of distilled water shown that flux is directly proportional to transmembrane pressure (TMP). At low reaction time (5 min), the water flux has no significant effect on water permeance. So, the reaction time has a significant effect on the growth of thin film.

Microporous carbon from fullerene impregnated porous aromatic frameworks for improving the desalination performance of thin film composite forward osmosis membranes

2018 ◽  
Vol 6 (24) ◽  
pp. 11327-11336 ◽  
Author(s):  
Xing Wu ◽  
Mahdokht Shaibani ◽  
Stefan J. D. Smith ◽  
Kristina Konstas ◽  
Matthew R. Hill ◽  
...  
Keyword(s):  
Thin Film ◽  
Organic Phase ◽  
Interfacial Polymerization ◽  
Water Flux ◽  
Forward Osmosis ◽  
Microporous Carbon ◽  
Film Composite ◽  
Thin Film Composite ◽  
Porous Aromatic Frameworks

Novel TFN-FO membranes with improved water flux have been synthesized by adding C60@PAF900 into the organic phase of interfacial polymerization.

scholarly journals Fabrication of a novel cyanoethyl cellulose substrate for thin-film composite forward osmosis membrane

2019 ◽  
Vol 1 (1) ◽  
pp. 18-32 ◽  
Author(s):  
Ke Zheng ◽  
Shaoqi Zhou
Keyword(s):  
Thin Film ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Salt Flux ◽  
Sem Images ◽  
Film Composite ◽  
Thin Film Composite ◽  
Reverse Salt Flux ◽  
Cyanoethyl Cellulose

Abstract In this study, cyanoethyl cellulose (CEC) was used as a membrane material, and polyvinylpyrrolidone (PVP) was used as pore-forming agent to prepare the substrates for the thin-film composite (TFC) forward osmosis (FO) membrane for the first time. The experimental results demonstrate that the properties of the substrates were significantly improved after PVP was added. The scanning electron microscope (SEM) images show that a two-sublayer structure, a fringe-like top sublayer and macrovoids with sponge-like wall bottom sublayer, were formed after the addition of PVP. These improvements contributed to improved membrane performance during FO tests. Meanwhile, after adding PVP, the TFC membranes exhibited good water flux, and excellent specific reverse salt flux. For instance, the TFC-M2 exhibited 9.10/20.67 LMH water flux, 1.35/2.24 gMH reverse salt flux, and 0.15/0.11 g/L specific reverse salt flux in FO/pressure-retarded osmosis mode while using 1 M NaCl as the draw solution and deionized (DI) water as the feed solution.

scholarly journals Effect of Kenaf MCC composition on Thin Film Composite membrane for NaCI Rejection

2019 ◽  
Vol 258 ◽  
pp. 04003
Author(s):  
Azman Ismail ◽  
Ramlah Mohd Tajuddin ◽  
Hamizah Mohktar ◽  
Ahmad Fauzi Ismail
Keyword(s):  
Thin Film ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Sem Images ◽  
Water Contact ◽  
Membrane Performance ◽  
Pure Water Flux

A modified thin film PSf-MCC reverse osmosis membrane was prepared by interfacial polymerization between aqueous MPD and TMC as the organic monomer. Aim of this study is to determine the effect of MCC in membrane formulation and fabrication. The surface and cross section morphology of TFC PSF/MCC membrane shows MCC particle which able to improve hydrophilicity of the membrane. The SEM images showed dense and porous structure of the MCC incorporated membranes. In addition, the water contact angle measurement also confirmed the increased hydrophilicity of the modified membranes. The effect of MCC on membrane matric influence the membrane performance in terms of NaCl rejection and pure water flux. Results showed that TFC PSf/MCC membrane shows NaCl rejection up to 98.9% compared with TFC PSf membrane. TFC PSf/MCC membrane also showed the highest pure water flux which is 3.712 Lm2/hr compare with TFC PSF membrane which is 3.606 Lm2/hr. The overall result proved that MCC particle could improve membrane hydrophilicity hence, increased pure water flux and salt rejection.

Synthesis and characterization of a polyamide thin film composite membrane based on a polydopamine coated support layer for forward osmosis

RSC Advances ◽  
2015 ◽  
Vol 5 (128) ◽  
pp. 106113-106121 ◽  
Author(s):  
Yangbo Huang ◽  
Haiyang Jin ◽  
Hao Li ◽  
Ping Yu ◽  
Yunbai Luo
Keyword(s):  
Thin Film ◽  
Composite Membrane ◽  
High Performance ◽  
Interfacial Polymerization ◽  
Forward Osmosis ◽  
Synthesis And Characterization ◽  
Film Composite ◽  
Thin Film Composite Membrane ◽  
Thin Film Composite

In this study, a facile method has been developed to prepare high performance thin film composite forward osmosis membranes, which was conducted by coating the surface of a polysulfone substrate with polydopamine prior to the interfacial polymerization.

Sign in / Sign up

Export Citation Format

Share Document