Green Extraction of Carotenoids from Fruit and Vegetable Byproducts: A Review

Carotenoids are characterized by a wide range of health-promoting properties. For example, they support the immune system and wound healing process and protect against UV radiation’s harmful effects. Therefore, they are used in the food industry and cosmetics, animal feed, and pharmaceuticals. The main sources of carotenoids are the edible and non-edible parts of fruit and vegetables. Therefore, the extraction of bioactive substances from the by-products of vegetable and fruit processing can greatly reduce food waste. This article describes the latest methods for the extraction of carotenoids from fruit and vegetable byproducts, such as solvent-free extraction—which avoids the costs and risks associated with the use of petrochemical solvents, reduces the impact on the external environment, and additionally increases the purity of the extract—or green extraction using ultrasound and microwaves, which enables a significant improvement in process efficiency and reduction in extraction time. Another method is supercritical extraction with CO2, an ideal supercritical fluid that is non-toxic, inexpensive, readily available, and easily removable from the product, with a high penetration capacity.

The Influence of Cutting Parameters on Plastic Deformation and Chip Compression during the Turning of C45 Medium Carbon Steel and 62SiMnCr4 Tool Steel

The paper deals with the issue of cutting zone and chip compression. The aim was to analyse the microstructure transverse section of the cutting zone on a metallographic cut, due to determined values of chip compression and plastic deformation, which affect the cutting process efficiency. The tested cutting tool material was coated with cemented carbide. The selected workpiece materials were C45 medium carbon steel of ISO grade and 62SiMnCr4 tool steel of ISO (W.Nr. 1.2101) grade. In the experiments, a DMG CTX alpha 500 turning centre was used. The cutting speed and feed were varied, and the depth of the cut was kept constant during the turning. The plastic deformation and chip compression determine the efficiency of the cutting process. The higher compression requires more work to perform the process and, therefore, it requires more energy for doing so. With the increase of the cutting speed, the deformation for C45 steel is decreased. The rapid deformation reduction was observed when the cutting speed was increased from 145 m/min to 180 m/min. Generally, deformation is decreasing with the increase of the feed. Only at a cutting speed of 145 m/min was the deformation elevation observed, when the feed was increased from 0.4 mm to 0.6 mm. During the turning of the 62SiMnCr4 tool steel we observed an error value at a cutting speed of 145 m/min and a feed of 0.4 mm was the middle cutting parameter. However, feed dependence was clear: With an increase of the feed, the plastic deformation was decreasing. This decreasing was more rapid with the increasing of the cutting speed. Besides plastic deformation, there was analysed chip compression as well. With the increasing of the cutting speed, there was a decrease of the chip compression. Due to a lack of information in the area of the chip compression and the plastic deformation in the cutting process, we decided to investigate the cutting zone for the turning of tool steels 62SiMnCr4, which was compared with the reference steel C45. The results could be applied to increase the efficiency of the process and improvement of the surface integrity.

Effect of Differently Matured Composts from Willow on Growth and Development of Lettuce

Soil amendments from peats, brown coals and composts produced from segregated biodegradable waste or biomass from fallow land can increase soil fertility and improve soil productivity. The aim of the study was to determine the possibility of using willow (Salix viminalis L.) biomass composts as a substrate component in horticulture. The objects of the research were composts produced from willow carried out in a pile under aerobic conditions. The addition of hay and mineral nitrogen (Nmin) was used to improve process efficiency. In order to verify the type and determine fertilizing value, basic chemical parameters were analyzed (pH, total contents of C, N and P) and a pot experiment was established to analyze the germination and growth of lettuce (Lactuca sativa L.). Changes in pH, an increase in total nitrogen content (TN), phosphorus (TP) and a decrease in TOC was observed in the investigated samples. Results of the experiment showed that the highest yield was obtained from the pots with the mixture of willow, hay and Nmin. Matured composts significantly stimulated the germination and growth of the test plants. It can be concluded that the addition of hay and Nmin significantly improved composting process and increased the fertilizing value of the investigated composts.

Three-dimensional convective dissolution of carbon dioxide into brine

The sequestration of carbon dioxide (CO2) through storage into deep saline aquifers represents an indispensable support technology to achieve the zero-carbon target necessary to mitigate the impact of CO2 on climate change. The effectiveness of the sequestration process, partly driven by the convective dissolution of CO2 in brine, is nowadays well characterized for two-dimensional geometries, low permeabilities, and small pressures of injection of CO2. However, reliable predictions of process-efficiency are missing because of the lack of full understanding of the three-dimensional (3D) spatio-temporal behaviour of CO2-rich convective fingers in brine over a large range of injection pressures. Here, we show that the convective dissolution is determined by the instability of the boundary layer formed at the interface between the two phases and is totally independent of the overall vertical size. Experiments were conducted over a broad range of injection pressures, close to process-relevant conditions. The results show the formation of complex 3D structures, including interconnecting stream tubes at the CO2-liquid interface, which could not be detected in previous 2D Hele-Shaw studies, and fingerings. A scale-free theoretical modelling of the convective process allows us to remap our laboratory results to length-scales of relevance for geological reservoirs. The experiments and the model show that the times needed for the onset of convection and the convective flux are independent of the system size.

Fouling Prevention in Polymeric Membranes by Radiation Induced Graft Copolymerization

The application of membrane processes in various fields has now undergone accelerated developments, despite the presence of some hurdles impacting the process efficiency. Fouling is arguably the main hindrance for a wider implementation of polymeric membranes, particularly in pressure-driven membrane processes, causing higher costs of energy, operation, and maintenance. Radiation induced graft copolymerization (RIGC) is a powerful versatile technique for covalently imparting selected chemical functionalities to membrane surfaces, providing a potential solution to fouling problems. This article aims to systematically review the progress in modifications of polymeric membranes by RIGC of polar monomers onto membranes using various low- and high-energy radiation sources (UV, plasma, γ-rays, and electron beam) for fouling prevention. The feasibility of the modification method with respect to physico-chemical and antifouling properties of the membrane is discussed. Furthermore, the major challenges to the modified membranes in terms of sustainability are outlined and the future research directions are also highlighted. It is expected that this review would attract the attention of membrane developers, users, researchers, and scientists to appreciate the merits of using RIGC for modifying polymeric membranes to mitigate the fouling issue, increase membrane lifespan, and enhance the membrane system efficiency.

Flushing of Soils Highly Contaminated with Cd Using Various Washing Agents Derived from Sewage Sludge

The suitability of sewage-sludge derived washing agents (SS_WAs) (dissolved organic matter DOM; humic-like substances HLS; soluble humic substances SHS), was assessed for removing Cd from highly contaminated (300 mg/kg) sandy clay loam and clay. The soils were remediated via column flushing at two flow rates, 0.5 and 1.0 mL/min. The stability of the flow velocity (FV) depended on the type of SS_WA and decreased in the following order: DOM > HLS > SHS. Cd was most effectively removed during the first hours of flushing, and the process proceeded with a first-order kinetics. The overall process efficiency was higher at flow rate of 1.0 mL/min than at 0.5 mL/min and ranged from 65.7 (SHS) to 75.5% (DOM) for the sandy clay loam and from 64.7% (SHS) to 67.8% (DOM) for the clay. However, all SS_WAs at both flow rates removed the most mobile Cd fraction (F1) with an efficiency above 90%. Flushing improved soil characteristics in terms of the content of organic matter, humic substances and nutrients. Among all SS_WAs, DOM was the most suitable for remediation of highly Cd-contaminated soils due to high efficiency of Cd removal, the high stability of its FV during flushing and the simple manner of DOM recovery from sewage sludge.