Comparison of Molecular Simulation and Pseudo-Rigid-Body Model Predictions for a Carbon Nanotube–Based Compliant Parallel-Guiding Mechanism

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Christopher M. DiBiasio ◽  
Martin L. Culpepper ◽  
Robert Panas ◽  
Larry L. Howell ◽  
Spencer P. Magleby
Keyword(s):  
Rigid Body ◽  
Molecular Simulation ◽  
Moment Of Inertia ◽  
Bulk Deformation ◽  
Body Model ◽  
Kinematic Behavior ◽  
Model Predictions ◽  
Rigid Body Model ◽  
Simulation Results ◽  
Selection Of

We report on the accuracy of the pseudo-rigid-body model (PRBM) in predicting the behavior of a nanoscale parallel-guiding mechanism (nPGM) that uses two single-walled (5,5) carbon nanotubes (CNTs) as the flexural guiding elements. The nPGM has two regions of behavior: region 1 is governed by the bulk deformation of the nanotubes, and region 2 is characterized by hingelike flexing of four “kinks” that occur due to buckling of the nanotube walls. PRBM parameters for (5,5) CNTs are proposed. Molecular simulation results of region 1 behavior match PRBM predictions of (1) kinematic behavior with less than 7.3% error and (2) elastomechanic behavior with less than 5.7% error. Although region 1 is of more interest because of its well-defined and stable nature, region 2 motion is also investigated. We show that the PRBM parameters are dependent on the selection of the effective tube thickness and moment of inertia, the lesson being that designers must take care to consider the thickness and moment of inertia values when deriving PRBM constants.

Compliant Pantographs via the Pseudo-Rigid-Body Model

1998 ◽  
Author(s):  
Andrew J. Nielson ◽  
Larry L. Howell
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Test Results ◽  
Rigid Link ◽  
Body Model ◽  
Design Flexibility ◽  
Model Predictions ◽  
Rigid Body Model ◽  
Classical Mechanism

Abstract This paper uses a familiar classical mechanism, the pantograph, to demonstrate the utility of the pseudo-rigid-body model in the design of compliant mechanisms to replace rigid-link mechanisms, and to illustrate the advantages and limitations of the resulting compliant mechanisms. To demonstrate the increase in design flexibility, three different compliant mechanism configurations were developed for a single corresponding rigid-link mechanism. The rigid-link pantograph consisted of six links and seven joints, while the corresponding compliant mechanisms had no more than two links and three joints (a reduction of at least four links and four joints). A fourth compliant pantograph, corresponding to a rhomboid pantograph, was also designed and tested. The test results showed that the pseudo-rigid-body model predictions were accurate over a large range, and the mechanisms had displacement characteristics of rigid-link mechanisms in that range. The limitations of the compliant mechanisms included reduced range compared to their rigid-link counterparts. Also, the force-deflection characteristics were predicted by the pseudo-rigid-body model, but they did not resemble those for a rigid-link pantograph because of the energy storage in the flexible segments.

Classification of Compliant Mechanisms and Determination of the Degrees of Freedom Using the Concepts of Compliance Number and Pseudo-Rigid-Body Model

2019 ◽  
Author(s):  
Pratheek Bagivalu Prasanna ◽  
Ashok Midha ◽  
Sushrut G. Bapat
Keyword(s):  
Rigid Body ◽  
Degrees Of Freedom ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Body Model ◽  
Active Compliance ◽  
Kinematic Behavior ◽  
Rigid Body Model

Abstract Understanding the kinematic properties of a compliant mechanism has always proved to be a challenge. A concept of compliance number offered earlier emphasized the development of terminology that aided in its determination. A method to evaluate the elastic degrees of freedom associated with the flexible segments/links of a compliant mechanism using the pseudo-rigid-body model (PRBM) concept is provided. In this process, two distinct classes of compliant mechanisms are developed involving: (i) Active Compliance and (ii) Passive Compliance. Furthermore, these also aid in a better characterization of the kinematic behavior of a compliant mechanism. A more lucid interpretation of the significance of compliance number is provided. Applications of this method to both active and passive compliant mechanisms are exemplified. Finally, an experimental procedure that aids in visualizing the degrees of freedom as calculated is presented.

Analysis of a Fixed-Guided Compliant Beam With an Inflection Point Using the Pseudo-Rigid-Body Model (PRBM) Concept

2012 ◽  
Author(s):  
Ashok Midha ◽  
Sushrut G. Bapat ◽  
Adarsh Mavanthoor ◽  
Vivekananda Chinta
Keyword(s):  
Boundary Condition ◽  
Boundary Conditions ◽  
Rigid Body ◽  
Inflection Point ◽  
Equilibrium Equations ◽  
Displacement Boundary ◽  
Body Model ◽  
Rigid Body Model ◽  
Domain Concept ◽  
Selection Of

This paper provides an efficient method of analysis for a fixed-guided compliant beam with an inflection point, subjected to beam end load or displacement boundary conditions, or a combination thereof. To enable this, such a beam is modeled as a pair of well-established pseudo-rigid-body models (PRBMs) for fixed-free compliant beam segments. The analysis procedure relies on the properties of inflection in developing the necessary set of static equilibrium equations for solution. The paper further discusses the multiplicity of possible solutions, including displacement configurations, for any two specified beam end boundary conditions, depending on the locations of the effecting force and/or displacement boundary conditions. A unique solution may exist when a third beam end boundary condition is specified; however, this selection is not unconditional. A deflection domain concept is proposed to assist with the selection of the third boundary condition in a more realistic manner.

Dynamic Response of Compliant Mechanisms Using the Pseudo-Rigid-Body Model

1997 ◽  
Author(s):  
Scott M. Lyon ◽  
Mark S. Evans ◽  
Paul A. Erickson ◽  
Larry L. Howell
Keyword(s):  
Dynamic Response ◽  
Rigid Body ◽  
Nonlinear Analysis ◽  
Natural Frequencies ◽  
Compliant Mechanisms ◽  
Experimental Results ◽  
Body Model ◽  
Straight Line ◽  
Model Predictions ◽  
Rigid Body Model

Abstract The pseudo-rigid-body modeling technique is used to simplify the nonlinear analysis of compliant mechanisms. This paper presents the first work that investigates the possibility of using the pseudo-rigid-body model to predict the dynamic response of compliant mechanisms. Four different configurations of the parallel-guiding mechanism are modeled and tested, as well as two configurations of compliant straight-line mechanisms. The model predictions of the first natural frequencies were compared with experimental results for all six mechanism configurations. The model predictions are within 9% of the experimental results for all cases.

Design and Testing of a Compliant Floating-Opposing-Arm (FOA) Centrifugal Clutch

2000 ◽  
Author(s):  
Nathan B. Crane ◽  
Larry L. Howell ◽  
Brent L. Weight
Keyword(s):  
Rigid Body ◽  
Test Data ◽  
Body Model ◽  
Model Predictions ◽  
Rigid Body Model ◽  
Contact Surfaces ◽  
Design And Testing

Abstract A floating-opposing-arm (FOA) centrifugal clutch is presented that uses compliant segments to reduce the part count and increase manufacturability. The clutch performs all of the functions of a centrifugal clutch, but consists of only two pieces. Torque is increased by connecting aggressive and non-aggressive contact surfaces in connected pairs. This arrangement increases the torque output of the FOA clutch by over 100% relative to a commercial one-piece compliant centrifugal clutch design of the same size and material. Yet, since this design is compliant, it remains simple to manufacture. This clutch is presented and modeled using the pseudo-rigid-body-model (PRBM) technique. The model predictions are compared to test data from five prototypes. The FOA clutch is also demonstrated in a gasoline-powered string trimmer.

Prediction of the First Modal Frequency of Compliant Mechanisms Using the Pseudo-Rigid-Body Model

1999 ◽  
Vol 121 (2) ◽  
pp. 309-313 ◽  
Author(s):  
S. M. Lyon ◽  
P. A. Erickson ◽  
M. S. Evans ◽  
L. L. Howell
Keyword(s):  
Rigid Body ◽  
Natural Frequencies ◽  
Compliant Mechanisms ◽  
Experimental Results ◽  
Modal Frequency ◽  
Body Model ◽  
Modal Response ◽  
Straight Line ◽  
Model Predictions ◽  
Rigid Body Model

The pseudo-rigid-body modeling technique is used to simplify the nonlinear analysis of compliant mechanisms. This paper presents the first work that investigates the possibility of using the pseudo-rigid-body model to predict the first modal response of compliant mechanisms. Four different configurations of the parallel-guiding mechanism are modeled and tested, as well as two configurations of compliant straight-line mechanisms. The model predictions of the first natural frequencies were compared with experimental results for all six mechanism configurations. The model predictions are within 9 percent of the experimental results for all cases.

A Simple and Accurate Method for Determining Large Deflections in Compliant Mechanisms Subjected to End Forces and Moments

1998 ◽  
Vol 120 (3) ◽  
pp. 392-400 ◽  
Author(s):  
A. Saxena ◽  
S. N. Kramer
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Elliptic Integral ◽  
Beam Equation ◽  
Large Deflections ◽  
Euler Beam ◽  
Body Model ◽  
Rigid Body Model ◽  
Analysis And Synthesis

Compliant members in flexible link mechanisms undergo large deflections when subjected to external loads. Because of this fact, traditional methods of deflection analysis do not apply. Since the nonlinearities introduced by these large deflections make the system comprising such members difficult to solve, parametric deflection approximations are deemed helpful in the analysis and synthesis of compliant mechanisms. This is accomplished by representing the compliant mechanism as a pseudo-rigid-body model. A wealth of analysis and synthesis techniques available for rigid-body mechanisms thus become amenable to the design of compliant mechanisms. In this paper, a pseudo-rigid-body model is developed and solved for the tip deflection of flexible beams for combined end loads. A numerical integration technique using quadrature formulae has been employed to solve the large deflection Bernoulli-Euler beam equation for the tip deflection. Implementation of this scheme is simpler than the elliptic integral formulation and provides very accurate results. An example for the synthesis of a compliant mechanism using the proposed model is also presented.

A Simple and Accurate Method for Determining Large Deflections in Complaint Mechanisms Subjected to End Forces and Moments

1998 ◽  
Author(s):  
A. Saxena ◽  
Steven N. Kramer
Keyword(s):  
Rigid Body ◽  
Numerical Integration ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Beam Equation ◽  
Integration Scheme ◽  
Large Deflections ◽  
Body Model ◽  
Rigid Body Model ◽  
Analysis And Synthesis

Abstract Compliant members in flexible link mechanisms undergo large deflections when subjected to external loads for which, traditional methods of deflection analysis do not apply Nonlinearities introduced by these large deflections make the system comprising such members difficult to solve Parametric deflection approximations are then deemed helpful in the analysis and synthesis of compliant mechanisms This is accomplished by seeking the pseudo-rigid-body model representation of the compliant mechanism A wealth of analysis and synthesis techniques available for rigid-body mechanisms thus become amenable to the design of compliant mechanisms In this paper, a pseudo-rigid-body model is developed and solved for the tip deflection of flexible beams for combined end loads with positive end moments A numerical integration technique using quadrature formulae has been employed to solve the nonlinear Bernoulli-Euler beam equation for the tip deflection Implementation of this scheme is relatively simpler than the elliptic integral formulation and provides nearly accurate results Results of the numerical integration scheme are compared with the beam finite element analysis An example for the synthesis of a compliant mechanism using the proposed model is also presented.

Sign in / Sign up

Export Citation Format

Share Document