Heat Transfer to an Airfoil in Oscillating Flow

1971 ◽  
Vol 93 (4) ◽  
pp. 461-468 ◽  
Author(s):  
J. A. Miller ◽  
P. F. Pucci
Keyword(s):  
Heat Transfer ◽  
Oscillation Frequency ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Oscillating Flow ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Consequent Increase

Local heat transfer coefficients to an airfoil in an oscillating stream have been measured for a range of frequencies and oscillation amplitudes. Results at moderate angles of attack are in agreement with previously reported findings. However, at large angles of attack, including those associated with stall in steady flow, a strong periodic starting vortex shed from the leading edge leads to a dramatic reattachment of the flow and consequent increase in local Nusselt Numbers of as much as five-fold. These effects are shown to be amplified by increasing oscillation frequency and amplitude.

Heat Transfer Enhancement in Triangular Ducts With an Array of Side-Entry Wall/Impinged Jets

1999 ◽  
Author(s):  
J.-J. Hwang ◽  
C.-S. Cheng ◽  
Y.-P. Tsia
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
Inclined Angle

An experimental study has been performed to measure local heat transfer coefficients and static well pressure drops in leading-edge triangular ducts cooled by wall/impinged jets. Coolant provided by an array of equally spaced wall jets is aimed at the leading-edge apex and exits from the radial outlet. Detailed heat transfer coefficients are measured for the two walls forming the apex using transient liquid crystal technique. Secondary-flow structures are visualized to realize the mechanism of heat transfer enhancement by wall/impinged jets. Three right-triangular ducts of the same altitude and different apex angles of β = 30 deg (Duct A), 45 deg (Duct B) and 60 deg (Duct C) are tested for various jet Reynolds numbers (3000≦Rej≦12600) and jet spacings (s/d = 3.0 and 6.0). Results show that an increase in Rej increases the heat transfer on both walls. Local heat transfer on both walls gradually decreases downstream due to the crossflow effect. At the same Rej, the Duct C has the highest wall-averaged heat transfer because of the highest jet center velocity as well as the smallest jet inclined angle. Moreover, the distribution of static pressure drop based on the local through flow rate in the present triangular duct is similar to that that of developing straight pipe flows. Average jet Nusselt numbers on the both walls have been correlated with jet Reynolds number for three different duct shapes.

Influence of High Mainstream Turbulence on Leading Edge Heat Transfer

1991 ◽  
Vol 113 (4) ◽  
pp. 843-850 ◽  
Author(s):  
A. B. Mehendale ◽  
J. C. Han ◽  
S. Ou
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Turbulence Decay ◽  
High Turbulence

The influence of high mainstream turbulence on leading edge heat transfer was studied. High mainstream turbulence was produced by a bar grid (Tu = 3.3–5.1 percent), passive grid (Tu = 7.6–9.7 percent), and jet grid (Tu = 12.9–15.2 percent). Experiments were performed using a blunt body with a semicylinder leading edge and flat sidewalls. The mainstream Reynolds numbers based on leading edge diameter were 25,000, 40,000, and 100,000. Spanwise and streamwise distributions of local heat transfer coefficients on the leading edge and flat sidewall were obtained. The results indicate that the leading edge heat transfer increases significantly with increasing mainstream turbulence intensity, but the effect diminishes at the end of the flat sidewall because of turbulence decay. Stagnation point heat transfer results for high turbulence intensity flows agree with the Lowery and Vachon correlation, but the overall heat transfer results for the leading edge quarter-cylinder region are higher than their overall correlation for the entire circular cylinder region. High mainstream turbulence tends not to shift the location of the separation-reattachment region. The reattachment heat transfer results are about the same regardless of mainstream turbulence levels and are much higher than the turbulent flat plate correlation.

Average Nusselt Number for Pressure and Suction Sides of Squealer Turbine Blade Tip

2011 ◽  
Author(s):  
Chaouki Ghenai
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Turbine Blade ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Cavity Depth ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Blade Tip

Numerical simulations of the flow field and heat transfer of squealer blade tip are performed in this study. The effect of Reynolds number (Re = 10000–40000), the clearance gap to width ratios (C/W = 5%–15%) and the cavity depth to width ratios (D/W = 10%, 20% and 50%) on fluid flow and heat transfer characteristics are obtained. The temperature and velocity distributions inside the cavity, the local heat transfer coefficients, and the average Nusselt numbers for the pressure and suction sides of the turbine blade tip are determined. This paper presents the results of the effects of Reynolds number, clearance gap and width ratios on the Nusslet number for the pressure and suction sides of squealer turbine blade tip. The results show a good agreement with the experimental data obtained by Metzger and Bunker. New correlations for the average Nusselt numbers for turbine blade tip pressure and suction sides are presented.

A Detailed Experimental Investigation of a Perforated Heat Transfer Surface Applied to Gas Turbine Recuperators

2003 ◽  
Author(s):  
Juan C. Adams ◽  
Peter T. Ireland ◽  
Martin Cerza ◽  
James Oswald
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Compact Heat Exchangers ◽  
Heat Transfer Coefficients ◽  
Extended Surfaces

An effort is made to explain and improve the understanding of the mechanisms behind the thermo-hydraulic performance of perforated extended surfaces used in compact heat exchangers in the laminar flow regime (ReD = 400–2500). A transient liquid crystal technique, which uses Helium as operating fluid, together with digital image photographic processing have been used to provide measurements of local heat transfer coefficients for this geometry. This work has found that through the use of perforated surfaces there exists a local heat transfer enhancement benefit. It has also been found that although perforations cause a partial restart of the thermal boundary layer, a significant overall surface heat transfer enhancement may not be achieved over plain surfaces. It was also found that the distance between the fin’s leading edge and the point of last significant enhancement resulting from a perforation, linearly depends on Reynolds number. Local heat transfer coefficient measurements were validated by single blow experimentation of similar geometries. The transient single blow technique used the curve-matching method to compare predicted and experimental temperatures.

Heat Transfer in the Oscillating Turbulent Boundary Layer

1969 ◽  
Vol 91 (4) ◽  
pp. 239-244 ◽  
Author(s):  
James A. Miller
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Mean Velocity ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Local Coefficients

Measurements of local heat-transfer coefficients in the fully established oscillating turbulent boundary layer over a flat plate are reported. In the range of frequencies from 0.1 to 200 cps and amplitudes from 8 to 92 percent of the freestream mean velocity, increases in local Nusselt numbers of 3 to 5 percent were found. It is concluded that substantial increases in local coefficients, sometimes reported in oscillating flows of low standing wave ratio, may be traced to reduced transition Reynolds numbers.

scholarly journals Heat Transfer in the Oscillating Turbulent Boundary Layer

1969 ◽  
Author(s):  
J. A. Miller
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Mean Velocity ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Local Coefficients

Measurements of local heat transfer coefficients in the fully established oscillating turbulent boundary layer over a flat plate are reported. In the range of frequencies from 0.1 to 200 cps and amplitudes from 8 to 92 percent of the freestream mean velocity increases in local Nusselt numbers of 3 to 5 percent were found. It is concluded that substantial increases in local coefficients sometimes reported in oscillating flows of low standing wave ratio may be traced to reduced transition Reynolds numbers.

Effect of Outflow Orientation on Heat Transfer and Pressure Drop in a Triangular Duct With an Array of Tangential Jets

2000 ◽  
Vol 122 (4) ◽  
pp. 669-678 ◽  
Author(s):  
J.-J. Hwang ◽  
B.-Y. Chang
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Loss Coefficient ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Transfer Characteristics

Experiments are conducted to study the heat transfer and pressure drop characteristics in a triangular duct cooled by an array of tangential jets, simulating the leading-edge cooling circuit of a turbine blade. Coolant ejected from a high-pressure plenum through an array of orifices is aimed at the leading-edge apex and exits from the radial outlets. Three different outflow orientations, namely coincident with the entry flow, opposed to the entry flow, and both, are tested for various Reynolds numbers 12600⩽Re⩽42000. A transient liquid crystal technique is used to measure the detailed heat transfer coefficients on two walls forming the leading-edge apex. Flow rate across each jet hole and the crossflow development, which are closely related to the local heat transfer characteristics, are also measured. Results show that increasing Re increases the heat transfer on both walls. The outflow orientation affects significantly the local heat transfer characteristics through influencing the jet flow together with the crossflow in the triangular duct. The triangular duct with two openings is recommended since it has the highest wall-averaged heat transfer and the moderate loss coefficient among the three outflow orientations investigated. Correlations for wall-averaged Nusselt number and loss coefficient in the triangular duct have been developed by considering the Reynolds number for three different outflow orientations. [S0022-1481(00)01204-4]

Enhanced Microchannel Heat Sinks Using Oblique Fins

2009 ◽  
Author(s):  
Yong-Jiun Lee ◽  
Poh-Seng Lee ◽  
Siaw-Kiang Chou
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Secondary Flows ◽  
Heat Sinks ◽  
Microchannel Heat Sink ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

Oblique fins created in a microchannel heat sink can serve to modulate the flow, resulting in local and global heat transfer enhancement. Numerical analysis of laminar flow and heat transfer in such modified microchannel heat sink showed that significant enhancement of heat transfer can be achieved with negligible pressure drop penalty. The breakage of continuous fin into oblique sections causes the thermal boundary layers to be re-initialized at the leading edge of each oblique fin and reduces the boundary-layer thickness. This regeneration of the entrance effect causes the flow to be always in a developing state thus resulting in better heat transfer. In addition, the presence of the smaller oblique channels causes a fraction of the flow to branch into the adjacent main channels. The secondary flows thus created improve fluid mixing which serves to further enhance the heat transfer. The combination of the entrance and secondary flow effect results in a much improved heat transfer performance (the average and local heat transfer coefficients are enhanced by as much as 80%). Both the maximum wall temperature and temperature gradient are substantially decreased as a result.

Analysis of Turbulent Flow and Heat Transfer in Internally Finned Tubes and Annuli

1979 ◽  
Vol 101 (1) ◽  
pp. 29-37 ◽  
Author(s):  
S. V. Patankar ◽  
M. Ivanovic´ ◽  
E. M. Sparrow
Keyword(s):  
Heat Transfer ◽  
Turbulent Flow ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Finned Tubes ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Fully Developed Turbulent Flow

The fully developed turbulent flow and heat transfer characteristics for tubes and annuli with longitudinal internal fins were analyzed via a mixing length model. The model takes account of the proximity of both the fin surfaces and the tube wall as well as of the gradients in the radial and circumferential directions. Application was made to air flows, and a single adjustable constant in the model was fixed by comparisons with experimental data for the friction factor and the circumferential-average Nusselt number for internally finned tubes. The local heat transfer coefficients exhibited a substantial variation along the fin height, with the smallest value (essentially zero) at the base and the largest value at the tip. Lesser and more gradual variations were exhibited by the local heat transfer coefficients on the wall of the tube or annulus. In general, the fins were found to be as effective a heat transfer surface as the wall (per unit area). Average Nusselt numbers and friction factors are presented for both the tube and the annulus.

Sign in / Sign up

Export Citation Format

Share Document